What Lights Should Be Turned On in Time When Driving in Foggy Weather?

2 Answers
OCarlos
07/28/25 7:27pm
When driving in foggy weather, it is necessary to turn on the fog lights, hazard warning flashers, and headlights in time. Safety precautions for driving in foggy weather: 1. Correct use of lights: Turn on fog lights in foggy weather as their light waves can penetrate the fog more easily and illuminate farther. When the fog is extremely thick, you can turn on the hazard warning flashers because yellow light has better penetration through fog. Remember not to use high beams, as their light waves will be reflected back by the fog, similar to shining on a vast white wall. 2. Use the horn for alerts when necessary: Since visibility is poor in foggy weather, it is advisable to honk the horn appropriately when overtaking, turning, or encountering pedestrians to provide a driving signal. 3. Reduce speed and avoid sudden braking: First, slow down. Poor visibility in foggy weather means most vehicles are moving slowly, and high speeds can easily lead to rear-end collisions. Additionally, reducing speed can help avoid sudden braking. It is difficult to judge distances in foggy conditions, and sudden braking can easily cause accidents for vehicles behind. 4. Avoid reckless overtaking: Do not rush to overtake in foggy weather, as low visibility makes it harder to assess the situation ahead of the vehicle in front. Therefore, especially in heavy fog, not only should you turn on the hazard warning flashers, but it is also best to maintain a certain distance and follow the vehicle in front. Only when you can confirm the situation ahead should you honk and pass at a low speed.
Was this review help?
8
0
Share
DelElijah
08/12/25 12:29am
The key to driving in fog is promptly turning on the fog lights, including both front and rear fog lights. I once encountered a dangerous situation while driving in fog when using high beams actually made it harder to see the road because the reflected light created a white wall effect. Fog lights are designed with a low angle and strong penetration, distributing light evenly to illuminate the road nearby without glare. My habit is to activate the fog lights as soon as I enter a foggy area, along with the position lights to enhance side visibility. I reduce speed to 40-50 km/h and maintain a following distance of at least 50 meters. Regularly checking the car lights is crucial—replace aging bulbs promptly. Don’t forget to use the air conditioning to defog the interior, which prevents blurred vision. Safety comes first, and these steps have ensured my safe return home every time I drive in fog. Developing good habits is essential.
Was this review help?
12
5
Share
Expand All
More Forum Discussions

Does the Enclave Need an Underbody Guard?

For urban road driving, installation is not necessary as city roads are generally smooth, and installing an engine guard may impair engine cooling. However, if the vehicle frequently travels on rough or mountainous roads, installation is recommended. Functions of an underbody guard: Keeps the engine compartment clean, preventing road water and dust from entering. Protects the engine from being struck by gravel or hard objects kicked up by tires during driving, as such impacts can damage the engine. Materials for engine guards: Steel plate: Durable and inexpensive, but heavy, which can increase fuel consumption and may interfere with engine drop in collisions. Plastic: Lightweight and cheap, but only effective against mud and sand, offering poor protection and short lifespan. Alloy: Lighter than steel and stronger than plastic, but relatively more expensive. Reinforced resin: Lightweight with good toughness, protects against minor impacts and prevents corrosion of the vehicle's underbody metal in humid conditions, avoiding rust and erosion.
7
5
Share

What is the general temperature for using car air conditioning in winter?

In winter, the car air conditioning temperature is generally set between 18 degrees Celsius and 25 degrees Celsius. Below are detailed introductions to specific components of the car air conditioning system: 1. Air conditioning pressure sensor: Usually installed after the dryer, it is used to detect the hydraulic pressure of liquid refrigerant flowing through the expansion valve. Three wires: detect high pressure and low pressure. In case of refrigerant leakage and compressor oil loss after a car collision, to prevent compressor damage due to lack of oil, once low pressure is detected, the compressor power is quickly cut off. When high pressure is detected, the compressor power needs to be reduced to avoid wasteful energy consumption. 2. Air conditioning temperature sensor: Usually installed inside the temperature sensing package, it is the evaporator temperature sensor. When the temperature drops to a certain level, the compressor needs to be shut down to prevent frosting and eventual ice blockage from further cooling. 3. Air conditioning compressor relay: Usually installed on the compressor, it is used to control the compressor's start, stop, and power switching functions.
20
5
Share

What to Do If a Car Is Not Used for a Long Time?

If a car is not used for an extended period, the following steps should be taken in advance: disconnect the power supply and remove the negative terminal; park it in a garage if available, otherwise find a safe, dry, and shaded location and cover it with a car cover; clean out all items inside the car, especially avoiding leaving snacks inside; maintain sufficient tire pressure by inflating the tires properly. When it's time to drive the car again, follow these steps: 1. Check for tire deformation: If the car remains stationary for a long time, the entire weight of the car is borne by the four tire contact points with the ground, which may cause pressure deformation. Replace the tires if any abnormalities are found. 2. Check tire pressure: Normally, tire pressure may decrease slightly, so it's necessary to inflate them appropriately. 3. Warm up the engine sufficiently: After prolonged parking, the engine oil settles at the bottom of the oil pan, leaving the engine components without lubrication. To allow sufficient time for the oil to lubricate all engine parts and reduce wear, the warm-up time should be slightly longer than usual.
18
1
Share

Where is the stamped VIN number on the Leopaard CS10?

The stamped VIN number on the Leopaard CS10 is located on the outer side of the B-pillar on the passenger side. Below are the specific details about the VIN: 1. First 3 characters: Indicate the country of production, manufacturer, and vehicle type. 2. Characters 4-8: Represent vehicle characteristics, such as vehicle category, body type, engine type, and gross weight rating. 3. The 9th character: Is a check digit used to verify the accuracy of the VIN. 4. The 10th character: Indicates the production year, showing when the vehicle was manufactured. 5. The 11th character: Represents the assembly location, with '0' indicating original factory assembly. 6. Characters 12-17: Are the production sequence number, used for recalls by the manufacturer in case of quality issues.
4
0
Share

Is Visual Carbon Deposit Cleaning Inside the Cylinder Necessary?

Visual carbon deposit cleaning inside the cylinder is necessary. Below is the relevant introduction to visual carbon deposit cleaning inside the cylinder: 1. Cleaning with detergent: Engine detergent is used to remove carbon deposits inside the engine. Generally, for not severe cases, it can achieve good cleaning results. If the carbon deposit is severe, it is recommended that the owner adopts the method of uncovering the cylinder head to clean the valves and cylinder walls. At this time, the operation will be relatively more complicated, so it is suggested that the owner chooses a guaranteed professional 4S store and asks professionals to clean it. 2. Do not use inferior oil: It is necessary to avoid using inferior or fake "three-no" lubricating oil. If inferior oil is used, over time, it will not only fail to achieve the purpose of cleaning the engine carbon deposits but may even damage the engine. Therefore, it is recommended that the owner usually goes to a formal repair shop for maintenance, which is more guaranteed.
20
2
Share

What are the reasons for the poor cooling effect of the Honda XRV air conditioner?

Here are the specific reasons for the poor cooling effect of the Honda XRV air conditioner: 1. Insufficient or low refrigerant: It may be caused by a small refrigerant leak. You can observe it from the sight glass on the dryer tank. When the air conditioner is running normally, if there are continuous bubbles in the sight glass, it indicates insufficient refrigerant. If obvious bubble flipping occurs, it means the refrigerant is severely insufficient. In this case, simply adding refrigerant can solve the problem. 2. Loose drive belt of the car air conditioner compressor: If the drive belt is loose, the compressor will slip during operation, leading to reduced transmission efficiency and a decrease in compressor speed. This results in reduced delivery of compressed refrigerant, causing the car air conditioner to not cool. If the compressor drive belt is too loose, it should be tightened. If it cannot be turned by hand, it indicates the belt is too tight and should be loosened slightly. If tightening is ineffective or the belt shows cracks, aging, or other damage, a new drive belt should be replaced.
8
1
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.