What kind of supercharging does the new LaCrosse use?

1 Answers
ArcherAnn
07/30/25 2:10am
The new LaCrosse uses a 2.0T turbocharger. Introduction to turbochargers: A turbocharger is essentially an air compressor that increases intake air volume by compressing air. It utilizes the inertial momentum of exhaust gases from the engine to drive the turbine in the turbine chamber, which in turn drives the coaxial impeller. The impeller then pressurizes the air delivered through the air filter pipe, forcing it into the cylinders. Structural principle of turbochargers: The exhaust gas turbocharger mainly consists of a pump wheel and turbine, along with some other control components. The pump wheel and turbine are connected by a shaft (called the rotor). The exhaust gases from the engine drive the pump wheel, which then rotates the turbine. The rotating turbine pressurizes the intake system.
Was this review help?
6
1
Share
More Forum Discussions

What does 'lim' mean on a car?

The 'lim' on a car refers to the speed limiter function button. When pressed while the vehicle is stationary, it activates the speed limiter function, which restricts the maximum speed to the set limit. Even if the accelerator is pressed further, the speed will not increase beyond this limit. Typically, pressing this button when the vehicle is stationary defaults the speed limit to 30 km/h. If pressed while driving, the current speed value is set as the speed limit trigger point. If the vehicle exceeds the set speed limit, the system will issue a warning. However, in situations like downhill driving where the speed reaches or exceeds the set limit, the active braking mode will not be engaged. If a speed limit lower than the current speed is set during driving, the vehicle will coast until the speed drops below the limit. The system allows exceeding the speed limit under certain special circumstances, and in such cases, the driver can exceed the limit as needed without triggering an audible warning from the system.
8
2
Share

How to Remove Scratches from Car Dashboard?

First, evenly apply the repair paste to the scratched area, making sure to work in sections—this can be done in three to four passes. Then, wait for 10 minutes. After 10 minutes, use a small piece of lint-free cloth to vigorously rub back and forth for 15 minutes. Note: rub back and forth, not in circular motions. Use a larger piece of non-woven cloth to clean the dashboard surface and observe the repair results. Repeat the above steps if necessary.
3
4
Share

What Are the Solutions for Car Seat Sagging?

Using a seat cushion is undoubtedly the easiest and also a very practical solution. Since the seat's standard itself cannot be measured, it is recommended to have the seat repaired at an auto shop as a better approach. You can purchase a seat of the same specifications online or at a store, allowing you to replace the old seat immediately. Generally, you can get it replaced at an auto repair shop, which is an excellent option for those who do not want to replace the entire seat. Usually, such car issues are covered by warranty, so it might be worth trying to use insurance.
10
0
Share

How to Eliminate the Circle Slash on the Dashboard?

If a circle slash appears on the dashboard, it may indicate that the car's handbrake is engaged. Lowering the handbrake will turn off the light. If this light is on without the handbrake being engaged, it could be due to insufficient brake fluid, which needs to be replenished promptly.
2
3
Share

How to Use Volvo's Parking Air Conditioning Control?

Before getting into the car, open all windows or doors to let the hot air out first. After driving for a while to completely dissipate the hot air, close the windows. The air conditioning usually has an internal and external circulation switch. When using external circulation, the air conditioning draws air from outside the car, while internal circulation reuses the air inside the car. Before parking, turn off the air conditioning first but keep the fan running to dry the ducts, reducing the chance of mold growth.
7
0
Share

How to Repair Cracked Car Leather?

Lay the cracked area flat on a workbench, apply acrylic resin into the crack, align the edges, and dry it with a hair dryer. First, lay the damaged area flat on a workbench. Take a piece of non-woven fabric slightly larger than the damaged area, insert it from the opening, and place it flat beneath the damaged spot. Then, apply leather adhesive into the damaged area and align the edges neatly. Place a layer of cotton cloth over the damaged area and press it with an iron to set the shape. Once the leather surface is smooth, remove the padding cloth and dry it with a hair dryer.
17
0
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.