What kind of car is Biuke?

What is the technique to turn off the daytime running lights on the 2021 Nissan X-Trail?

2021 Nissan X-Trail daytime running lights can be turned off by inserting the car key and turning it to the position where only the radio can be used. Then, pull the switch on the left side of the combination switch towards the driver and push it down simultaneously. It's crucial to hold it in this position without releasing. Here's some related information about daytime running lights: Function: These lights make the vehicle more noticeable during daytime driving. Their purpose is not to help the driver see the road better but to alert others that a vehicle is approaching. Therefore, these are not illumination lights but signal lights. Purpose: The primary goal of daytime running lights is to enhance traffic safety. As a result, many countries have established regulations in recent years to ensure that the production and installation of daytime running lights effectively contribute to safety.

10

2

Share

What are the causes of low engine coolant?

Engine coolant being too low can be caused by the following reasons: 1. Low engine coolant may result from faults in the water temperature gauge and its circuits, damage to the water temperature sensor, a thermostat valve stuck open, failure of the louver to close due to a temperature control switch issue, or faults in the fan motor circuit causing the fan to run continuously. For vehicles equipped with a viscous fan clutch, a malfunction in the viscous clutch can also lead to this issue. 2. The cooling system operates by circulating coolant through the water pump to remove heat from the engine, achieving a cooling effect. If the engine coolant level is too low, it will disrupt the circulation and cooling process, potentially causing engine damage. 3. Coolant is an essential part of a car engine, circulating within the engine cooling system to carry away excess heat generated during engine operation, ensuring the engine operates at its normal working temperature.

13

4

Share

Why does the Audi A4L have higher shift-up RPM when the AC is on?

Audi A4L having higher shift-up RPM when the AC is on is a normal phenomenon. Basis for judgment: Because the vehicle's AC is still connected to the car engine, turning on the AC inherently increases the engine load. The engine also needs to increase its RPM accordingly. If the engine power increases, the temperature will naturally rise. Solutions for excessively high RPM: Under normal circumstances, when the car is idling with the AC on, the engine RPM may increase from about 800 to approximately 1500 RPM. An increase to 2500 RPM is considered excessively high, indicating there might be a fault in the engine control system, and the vehicle should be taken to a repair shop for inspection.

4

3

Share

What type of engine oil is suitable for the Volkswagen Tiguan L?

For both the 1.4T and 2.0T models of the Volkswagen Tiguan L, the recommended engine oil type is 5W40. The functions of engine oil and the meaning of the letters in the oil type are as follows: Functions of engine oil: Engine oil serves to lubricate, clean, seal, cool, cushion, and prevent rust within the engine. Meaning of the letters in the oil type: The 'W' in the oil type stands for 'Winter,' indicating that the oil can be used normally in winter conditions. The number before the 'W' represents the oil's low-temperature flow performance: 0W means the oil can flow normally at -35°C, while 5W indicates normal flow at -30°C. The number after the 'W' represents the oil's high-temperature viscosity—the higher the number, the greater the viscosity.

8

4

Share

Squeaking Sound When Lightly Pressing the Brakes?

The causes of squeaking sounds when lightly pressing the brakes include: installation of new brake pads; presence of small stones or sand between the brake disc and brake pads; or water between the brake pads and brake disc. Here are the solutions for addressing squeaking sounds when braking: 1. Worn or stuck release bearing, loose wear on the release lever pin and pin hole, or loose wear on the drive pin and pin hole; 2. When diagnosing clutch sounds, lightly press the clutch pedal to bring the release bearing into contact with the release lever. The sound from the release bearing may be due to lack of lubrication, looseness, or damage to the bearing; 3. Continuously press and release the clutch pedal. When the clutch is engaged or disengaged, assess the severity of the sound separately. Possible causes include loose wear on the release lever pin hole and support pin, loose rivets on the driven disc assembly, or failure of the vibration damper.

19

3

Share

What gear should be used when stopping at a red light?

What gear to use when stopping at a red light depends on the waiting time. The following are the gear selection scenarios when stopping at a red light: 1. If the red light lasts less than 30 seconds, it is recommended that the driver simply keep the brake pedal pressed. 2. If the red light lasts between 30 seconds and 1 minute, the driver should shift to N (Neutral) gear. 3. If the red light lasts more than one minute, it is recommended to shift directly to P (Park) gear. Additional information: For automatic transmission vehicles, when turning off the engine or idling for an extended period, the gear should be shifted to P (Park). The correct parking method is to first press the brake and shift to N (Neutral) gear, then engage the handbrake and release the brake pedal. Once the vehicle is completely stationary, shift to P (Park) gear.

4

3

Share

What kind of car is Biuke?

What is the technique to turn off the daytime running lights on the 2021 Nissan X-Trail?

What are the causes of low engine coolant?

Why does the Audi A4L have higher shift-up RPM when the AC is on?

What type of engine oil is suitable for the Volkswagen Tiguan L?

Squeaking Sound When Lightly Pressing the Brakes?

What gear should be used when stopping at a red light?

What Are the Effects of Pressing the Accelerator While in P Gear?

Where is the cabin air filter located in the Mercedes-Benz C260L?

Where is the BCM control module located in the ix35 body?

Working Principle of Automotive Urea?