What items need to be done for the second maintenance?

2 Answers
Delaney
07/25/25 1:33pm
The items that need to be done for the second maintenance include: replacing the engine oil and oil filter, replacing or cleaning the air and cabin air filters, and inspecting and maintaining dozens of items across multiple systems such as the engine, transmission, air conditioning system, steering system, braking system, suspension, body, and tires. The precautions for car maintenance are as follows: 1. Regularly check whether antifreeze, brake fluid, windshield washer fluid, etc. are sufficient. Antifreeze ensures normal driving of the vehicle in winter and prevents freezing. Brake fluid is an essential component of the braking system. Windshield washer fluid is used to clean the windshield. All these must be kept sufficient to ensure the normal operation of the vehicle. 2. Perform wheel alignment regularly. 3. Regularly inspect the brake pads. Check the wear degree of the car's brake pads and clutch plates on schedule. When the car is driving on the road, the brake pads and clutch plates are constantly wearing. They need to be replaced when they reach a certain degree of wear, otherwise, there will be great safety hazards.
Was this review help?
10
0
Share
StAriel
08/11/25 8:46pm
New car owners who just completed their second maintenance, let's chat! The second maintenance usually occurs at around 10,000 kilometers or six months, with the basic items being an oil and oil filter change—this is like giving your engine a spa treatment. The air filter also needs to be checked; if it's clogged, it can affect performance and increase fuel consumption. Tires and rims should be inspected carefully, with tire pressure adjusted properly, and front and rear tires rotated to ensure even wear. Brake pad thickness is crucial—if they're too thin, they need replacement. Various fluids, such as brake fluid and coolant, should be checked for levels and condition. Last time, I also found my wiper blades were worn out and replaced them on the spot. Don’t miss out on free inspection items, such as chassis bolt tightening and lighting system adjustments. Before maintenance, remember to check the manual to avoid being upsold unnecessary services.
Was this review help?
4
2
Share
Expand All
More Forum Discussions

What is the method for removing a car tire?

The method for removing a car tire is: 1. Use a socket wrench to loosen the tire's fixing screws in a diagonal sequence; 2. Place the jack into the slot and use it to lift the vehicle; 3. Remove the loosened screws one by one to detach the tire. Situations requiring tire replacement: 1. Tire deformation; 2. Severe damage to the tire body; 3. Severe damage to the tread; 4. Damage to the bead; 5. Bulging or cracking on the tire sidewall; 6. Damage from running flat; 7. Tires patched more than three times; 8. Tires worn to the wear limit; 9. Chemical corrosion; 10. Severe aging and peeling.
4
4
Share

What is the actual measured ground clearance of the Odyssey?

Odyssey ground clearance is 126MM. Introduction to ground clearance: The ground clearance of a vehicle refers to the distance between the ground and the lowest point of the rigid components at the bottom of the vehicle when it is parked horizontally on a level surface. It is also commonly known as the minimum ground clearance. This is an important parameter in automotive design, as the size of the ground clearance directly affects the vehicle's off-road capability and appearance. Large ground clearance: The greater the minimum ground clearance, the stronger the vehicle's ability to pass over obstacles or uneven terrain, but with a higher center of gravity, stability is reduced. Small ground clearance: The smaller the minimum ground clearance, the weaker the vehicle's ability to pass over obstacles or uneven terrain, but with a lower center of gravity, stability can be increased.
2
5
Share

How to Adjust the High and Low Beams of Car Lights?

There are fixed screw holes for the headlights that can be adjusted. Below are the methods to adjust car lights: 1. Adjusting the height and vertical alignment of car headlights: There is a headlight height adjustment knob next to the steering wheel to meet the need for adjusting the headlight height; 2. The height of car lights is usually adjusted at the factory. If the headlights have been repaired or replaced later, it is very likely that the light height may be incorrect. If the height is too high, the low beam may be mistaken for the high beam; if the height is too low, nothing can be seen beyond 10 meters at night; 3. The preparation work for adjusting car light height is to ensure the car is unloaded, with no passengers or heavy items inside, otherwise the body's sinking height will be affected, leading to accuracy issues in adjustment.
3
0
Share

Where is the OBD port located on the Haima S5?

The OBD port of the Haima S5 is located inside the storage compartment below the left side of the steering wheel. Here is some information about OBD: 1. OBD is the abbreviation of On-Board Diagnostics, which translates to "On-board Automatic Diagnostic System" in Chinese. 2. This system continuously monitors the engine's operating conditions to check if the vehicle's emissions exceed the standard. Once exceeded, it will immediately issue a warning. Additional information: 1. OBD not only involves automotive technology itself but is also limited by related conditions such as fuel quality, and it also places higher usage requirements on drivers. 2. The OBD device monitors multiple systems and components, including the engine, catalytic converter, particulate trap, oxygen sensor, emission control system, fuel system, EGR, etc.
20
5
Share

How to Remove Cement Slurry from a Car?

To remove cement slurry from a car, follow these methods: 1. Rinse it off with clean water before the cement slurry hardens; 2. Spray white vinegar or a specialized cement cleaner onto the cement slurry, wait for it to soften, and then rinse it off with clean water; 3. Pour gasoline onto the cement slurry, wait for the car paint to soften, and then rinse the cement slurry off with water. To maintain the car's paint: 1. Wash the car only after the engine has cooled down; 2. Minimize exposure to direct sunlight; 3. Clean any stains on the car body promptly; 4. Rinse the car with clean water after rain to prevent acid rain corrosion; 5. Apply wax or glaze regularly.
10
4
Share

What Does Cold Start Mean for a Car?

Cold start of a car refers to starting the engine when it has been shut down for a period of time, and its internal temperature has reached equilibrium with the ambient temperature. In contrast, there is also engine hot start, which means starting the engine shortly after it has been shut down, while it still retains significant residual heat. Cold starts are more challenging than hot starts, especially in low ambient temperatures and when using diesel fuel. The steps to start a car are: 1. Insert the key and turn it to the second position (power mode), wait for the system to complete self-check; 2. Shift the gear lever from P (Park) to N (Neutral); 3. Release the brake and start the engine; 4. Press the brake pedal, shift the gear lever from N to D (Drive), release the brake, and press the accelerator to begin driving.
18
3
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.