What items are included in the physical examination for a driver's license?

1 Answers
DiTanner
07/30/25 12:26am
The main items for the driver's license physical examination are as follows: 1. Age: 18-70 years old; 2. Height: No restriction; 3. Vision: Naked or corrected vision of both eyes must reach 4.9 or above on the logarithmic visual acuity chart (equivalent to 0.8 on the E-chart); 4. Color discrimination: No red-green color blindness; 5. Hearing: Ability to distinguish the direction of sound sources with each ear at a distance of 50 cm from a tuning fork; 6. Upper limbs: Both thumbs must be intact, and each hand must have at least three other fingers intact with normal movement function; 7. Lower limbs: Normal movement function, with a length difference between the lower limbs not exceeding 5 cm; 8. Trunk and neck: No movement dysfunction.
Was this review help?
7
4
Share
More Forum Discussions

How to Use the Tank Turn Feature on the Land Cruiser?

Land Cruiser tank turn method is as follows: 1. Shift to N gear. 2. Engage low-range four-wheel drive. 3. Shift to D gear. 4. Activate crawl mode and release the brake. 5. Turn the steering wheel to a certain angle. 6. Press the tank turn button and control speed with the speed button. Additional information about the Land Cruiser: 1. The Toyota Land Cruiser is an imported ORV off-road vehicle produced by Toyota. 2. The Land Cruiser's body dimensions are 4670mm in length, 1905mm in width, 1830mm in height, with a wheelbase of 2690mm.
11
0
Share

What is the tire specification for the Lynk & Co 01 Hybrid?

The tire specification for the Lynk & Co 01 Hybrid is 235/50R19. For models equipped with 19-inch wheels, the tire specification is 235/50R19; for models with 18-inch wheels, it is 235/55R18; and for models with 17-inch wheels, it is 235/50R17. The Lynk & Co 01 Hybrid measures 4549mm in length, 1860mm in width, and 1689mm in height, with a wheelbase of 2734mm. It features a 5-door, 5-seat SUV body structure, equipped with a 7-speed dual-clutch transmission and a 1.5T 180-horsepower L3 engine. The maximum power output is 132kW, and the top speed is 205km/h.
20
3
Share

Where is the Tire Pressure Monitoring on Haval H6?

Haval H6's tire pressure monitoring is located on the dashboard. The vehicle comes equipped with a tire pressure monitoring system that automatically alerts the driver without requiring manual operation. When the tire pressure light comes on and needs to be reset, if the tire pressure sensor has not been replaced, the light will automatically turn off after driving a certain distance. If the tire pressure sensor has been replaced, it is necessary to visit a 4S shop for matching with a specialized computer. The tire pressure monitoring system uses wireless transmission technology, employing highly sensitive miniature wireless sensors to collect data on tire pressure and temperature, whether the vehicle is in motion or stationary. This data is then transmitted to the main unit, where it is displayed digitally in real-time, showing relevant data such as tire pressure and temperature. In case of any abnormalities in the tire, the system alerts the driver through beeping sounds or voice prompts. In terms of body dimensions, the Haval H6 measures 4653mm in length, 1886mm in width, 1730mm in height, with a wheelbase of 2738mm.
20
3
Share

What to Do When There Is Water in the Car's Rear Tail Light?

Solutions for water in the car's rear tail light: 1. For minor water ingress, turn on the lights for a while, and the moisture will evaporate through the vent tube with the heat, without damaging the tail light or electrical circuits. 2. For severe water ingress, visit a 4S shop for disassembly and repair as soon as possible. If you have the tools, you can also disassemble it yourself. After opening the lens and drying it, check the tail light surface for any damage or potential water leakage points. If any abnormalities are found, it is recommended to replace the tail light cover seal and vent tube. The car tail light includes the lamps and bulbs in the rear of the car. One function of the lamps is to gather and emit the light from the bulbs, thereby enhancing the brightness and range of the light. The second function is to change the color of the bulb's light through the lamp's color. There are mainly three types of bulbs: halogen car bulbs, HID car bulbs, and the emerging LED car bulbs.
6
3
Share

What are the reasons why the Wuling Hongguang mini cannot be charged?

Wuling Hongguang mini cannot be charged due to: poor contact between the car charger and the charging equipment, unstable voltage of the car charger, or quality issues with the car charger itself. Poor contact between the car charger and the charging equipment. Since the vehicle usually shakes while driving, the charging interface may be shaken loose, resulting in no power connection and inability to charge. The solution is to reconnect it. Unstable voltage of the car charger, causing the battery protection mechanism of the charging equipment to activate, resulting in inability to charge. Sometimes the output of the car charger is not stable enough. Most electronic products have a protection mechanism to avoid damage from fluctuating currents, which can also prevent charging. It is recommended to use the USB interface of the car audio computer system for charging. Quality issues with the car charger itself may cause inability to charge. If you purchase counterfeit products, not only will they fail to charge, but they may also burn out car fuses and digital products, and even pose a risk to personal safety. It is recommended to replace the car charger with a high-quality one.
18
3
Share

What is the method for replacing car shock absorbers?

Car shock absorber replacement method is: 1. Loosen the wheel nuts in a diagonal sequence, but do not remove them completely. Use a lift to raise the vehicle to a height that is convenient for operation; 2. Remove all wheel nuts in a diagonal sequence and take off the wheels. Some models may require removing the brake caliper for easier shock absorber removal. Remove the control arm fixing bolts, then loosen the fixing nut of the spring strut arm; 3. Use a clamp jack to secure the shock absorber arm. Open the engine hood and loosen the upper body fixing nut of the shock absorber. Completely loosen the upper body fixing nut of the shock absorber and remove it; 4. After removing the shock absorber, use a spring compressor to secure the spring. Disassemble and replace damaged components and rubber boots of the shock absorber. Apply grease during reassembly to enhance wear resistance; 5. Secure the upper part of the shock absorber to the car body to prevent it from falling. Use a clamp jack to secure the shock absorber arm and lift it upwards to ensure the lower part can be placed on the front axle support. Then tighten the upper body fixing nut of the shock absorber properly; 6. After replacing the shock absorber, use a wrench to tighten the wheel fixing nuts. The shock absorber replacement is now complete.
3
0
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.