What items are included in the first maintenance of the Vezel?

[Greyson]

The first maintenance at a 4S shop includes the following aspects: changing the engine oil and oil filter, cleaning the air filter; checking the levels of various fluids to ensure they are normal, inspecting the generator belt and wiper blades for damage; checking tire pressure for normalcy and examining tires for uneven wear, bulges, or damage; inspecting the chassis, including brake pads, brake discs, connecting rods, ball joints, CV joints, and checking for scratches, etc.; examining all switches in the vehicle; ensuring all lights are functioning properly. Estimated time: Completing all tasks takes about 2 hours. Items required for the first maintenance include: driver's license; maintenance manual; warranty manual; owner's ID card; vehicle registration certificate; vehicle purchase invoice. Take these to the designated first maintenance facility for the vehicle's first service. Note: Make an appointment with the 4S shop in advance. The first maintenance refers to the initial service after a new car has been driven, with specific timing varying by vehicle, typically after driving 1,000 to 3,000 kilometers. It's essential to attend the first maintenance promptly, neither early nor delayed. The completion of the first maintenance marks the end of the vehicle's break-in period, allowing it to be driven under standard load and normal speeds as required by the vehicle. The timing for the first maintenance is calculated from the date of vehicle pickup. There are two indicator values for the first maintenance: mileage and time. Whichever comes first serves as the standard. The following inspections and replacements must be completed during the first maintenance of a new car: changing the engine oil, cleaning the three filters (oil filter, fuel filter, and air filter); checking the coolant level to ensure it is normal; inspecting the vehicle's brake and clutch fluid levels; checking the power steering fluid level and looking for leaks at all fluid pipe connections; workers should inspect the generator, air conditioning, water pump, and belts for aging and tension; checking tire pressure and wear condition, adjusting tire pressure, or performing tire rotation if there is wear. When changing the oil, the oil filter must also be replaced. The choice of oil must refer to the "Vehicle Use and Maintenance Manual," as different vehicle models specify different oil grades. Maintenance precautions: Do not rinse the interior of the car body with water: Many people clean their cars during holidays, rinsing the body with water and wiping it with a cloth. It's important to note that the interior of the car body should not be directly washed with water. If the floor mats are dirty, use a vacuum cleaner or take them out, scrub with a brush and detergent, dry them, and then put them back. There are many drainage holes under the rubber mats on the cabin floor. If water enters, it won't dry but will flow through the holes to areas like the transmission, causing corrosion. The best practice is to clean with a vacuum and then wipe with a cloth to prevent water accumulation. Do not mix different brands of antifreeze: When the antifreeze in the car is low, it's recommended to drain the existing antifreeze and refill with the same brand from the start. Different brands of antifreeze have varying chemical properties, and the corrosion inhibitors in one brand may corrode those in another. Different brands use different corrosion inhibitors, so they should not be mixed to avoid unnecessary issues. Do not lubricate tire bolts and nuts: When bolts on a car rust, they are often oiled to function properly again. Some people apply lubricant to bolts and nuts to prevent rust, but this can pose safety risks. At high speeds, bolts and nuts may loosen or even fall off, leading to driving hazards. Do not press the accelerator when starting an EFI car: The starter of an EFI car differs from that of a conventional car. Its fuel injection control system can automatically adjust fuel supply based on the starter's temperature and operating conditions, ensuring a smooth start.

[LaJulian]

As someone who cares about car details, I took the Vezel for its first maintenance and learned a lot. It included changing the engine oil and oil filter to remove metal debris generated during the engine break-in period, preventing clogs; checking the levels of coolant, brake fluid, and antifreeze to ensure no shortages affect cooling; testing tire pressure and wear, adjusting to the correct PSI to prevent unstable tire pressure; lighting system checks included adjusting the brightness of headlights and taillights to ensure nighttime safety; they also provided a complimentary exterior wash, which felt quite thoughtful. 4S shops typically inspect brake performance, battery status, and the air filter to prevent potential failures. In summary, these services make the new car run smoother, and you can drive with peace of mind until the next maintenance.