What is the wiper size of the Audi Q2L?

2 Answers
SanTucker
07/24/25 11:00am
The main wiper size of the new Audi Q2L is 24 inches, and the secondary wiper size is 21 inches. Different wiper sizes: The wiper sizes for the driver's side and the passenger's side are different. Generally, the driver's side is longer, and the passenger's side is shorter. In this case, be careful not to install them backward. If both wipers are the same size, it doesn't matter. Wiper installation: Wipers are installed below the windshield. For hatchbacks, the rear door and the rear windshield are integrated, so placing the wiper on the rear door prevents interference between them. For sedans, the rear door and the rear windshield are not integrated, and opening the rear door can cause misalignment between the rear windshield and the wiper.
Was this review help?
16
2
Share
SanOwen
08/11/25 6:00am
I previously drove an Audi Q2L and just replaced the wiper blades myself last year. The original wiper sizes for this model are 26 inches (approximately 65 cm) for the driver side and 18 inches (about 45.5 cm) for the passenger side. When purchasing, make sure to confirm the connector type, as most Audi models use U-hook attachments. Replacing them is quite simple: lift the wiper arm, press the release tab to remove the old blade, then align the new wiper with the slot until it clicks into place. Just be careful not to let the wiper arm snap back and hit the windshield. I recommend buying quality brands like Bosch for more durable rubber blades. Wiper blades are consumables and should be replaced if they streak, chatter, or make unusual noises. By the way, there might be slight variations between different model years, so measuring your original wipers is the safest approach if you're unsure.
Was this review help?
7
5
Share
Expand All
More Forum Discussions

How many years can the battery of Volkswagen Tayron last?

Generally, the service life of a vehicle battery is about 3 years, although this is related to the frequency of vehicle driving and the duration of each trip. To extend the battery's lifespan, avoid using in-car electrical equipment when the vehicle is not started. Below is relevant information: Exterior: The TAYRON adopts the new "Sharp & Stylish" design philosophy, embodying the three key concepts of "Strength, Premium, and Pioneering," which comprehensively indicate the future design direction of Volkswagen SUVs. Interior: The TAYRON's wrap-around cockpit design complements its rugged exterior, enhanced by multiple geometric cutting and folding line designs that emphasize a sense of strength. The Floating design of the center console is simple and elegant, with a clear functional layout and detailed designs that add a sense of quality. Coupled with the extensive use of soft interior materials, it creates a warm and comfortable interior environment for drivers and passengers, conveying a strong sense of technology and comfort, elevating the interior of German SUVs to a new level.
11
0
Share

Why is the airbag warning light on in the Volkswagen Lavida?

The airbag warning light being on in the Volkswagen Lavida indicates a fault in the airbag system. Below is relevant information about Volkswagen: Development History: Volkswagen (German: Volkswagen) is an automobile manufacturing company headquartered in Wolfsburg, Germany, and is the core enterprise of the Volkswagen Group, one of the world's four largest automobile manufacturers. In 2019, it ranked 9th in the Fortune Global 500. Brand Logo: Volkswagen (German: VolksWagenwerk), meaning "the people's car," has undergone several changes in its logo history. The VW in the logo stands for the first letters of the full name. The logo appears to be composed of three "V"s made with the middle and index fingers, symbolizing the victory of Volkswagen and its products.
7
4
Share

How many kilometers should the full synthetic oil of Accord be replaced?

Accord full synthetic oil should be replaced every 8,000 to 10,000 kilometers. Engine oil is known as the blood of the engine. Without engine oil, the engine cannot operate normally. Engine oil needs to be replaced regularly, as its lubricating performance deteriorates over time. If not replaced, it will accelerate engine wear. Here are some related details about engine oil: 1. When replacing the engine oil each time, the oil filter should also be replaced. The oil filter is used to filter the oil. Without it, the oil will become very dirty after some time, affecting the engine's lubrication. 2. When choosing engine oil, it is essential to select the oil viscosity suitable for your car's engine. The oil viscosity should not be too low or too high. If the viscosity is too low, it will increase engine wear; if the viscosity is too high, it will increase the resistance during engine operation, affecting power output and fuel consumption.
19
2
Share

What to do if the trunk light is not working?

Solutions for a non-working trunk light: 1. First, open the trunk. On the left side (near the taillight), carefully use a screwdriver to pry out the lamp holder from one end. You will then see the bulb. Try replacing it with a new one. 2. If the issue is with the wiring or switch, it is recommended to visit a 4S shop or auto repair shop to diagnose the problem. Here is some related knowledge about trunk lights: 1. The trunk light switch is integrated with the trunk switch. It can be considered as a sensor device, usually located near the latch of the trunk door. 2. When the door is closed, it triggers the sensor, and the trunk light turns off, similar to how a refrigerator light turns off when the door is closed. To turn off the trunk light, simply close the trunk.
4
5
Share

How to reset the maintenance wrench light on Arrizo 5?

The following are the manual steps to reset the maintenance light on Arrizo 5: 1. First, turn off the ignition switch and shut down the car; 2. Then locate the "Menu Switch" button on the steering wheel, which is the button with two overlapping squares; 3. Press and hold the "Menu Switch" button, then turn the ignition switch to the "ON" position; 4. After the car is powered on, the vehicle will start self-checking. Keep pressing the "Menu Switch" button during this time. After the self-check is completed, in about 5 seconds, the maintenance light will be reset; 5. Restart the car, and the maintenance light will no longer come on.
2
3
Share

How to Check China V and China VI Emission Standards?

Steps to check China V and China VI emission standards: 1. For new vehicles, the purchase will include a vehicle acceptance form, which states the emission standard. The China V emission standard is marked with a "V", while the China VI emission standard is marked with a "Ⅵ", both using Roman numerals. 2. For used vehicles, the emission standard can be checked by entering the vehicle model number on the environmental protection website. Below is more information about checking on the environmental protection website: 1. First, you need to know the vehicle model number of the car you want to check. The vehicle's nameplate will display the model number. 2. Visit the Motor Vehicle Environmental Protection Website, enter the fuzzy condition (vehicle model number) in the search box, input the correct verification code, and click "Query" to find relevant information about the vehicle, including the emission standard.
15
1
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.