What is the windshield size of the new Santana?

1 Answers
DiAmir
07/29/25 8:35pm
The front windshield size of the new Santana is 1400X700mm, and the rear windshield size is 1350X720mm, with a thickness of 3.2mm-6mm. Detailed information about car windshields is as follows: Precautions for selecting windshields: Choose formal channels and manufacturers to avoid being deceived. Legitimate manufacturers must have 3C certification. The edges of qualified glass are relatively smooth after breaking, while counterfeit glass is very sharp. Precautions after replacing the windshield: Do not wash the car within three days after replacing the windshield. Remove the tape fixing the windshield position after three days. Try to avoid driving on excessively bumpy roads and avoid emergency braking and rapid acceleration to prevent the windshield from shifting.
Was this review help?
19
3
Share
More Forum Discussions

How to Remove the Rear Seats of a Focus?

Method for removing the rear seats of a Focus: 1. Push the clips on both sides of the rear seat cushion inward and lift the cushion; 2. Unscrew the bolts between the seat cushion and the backrest; 3. Remove the seat cushion and the rear backrest; 4. Remove the bolts under the rear backrest; 5. Hold the hooks behind the seat cushion and backrest firmly and lift the rear seats upward. Taking the 2020 Focus as an example, its body dimensions are: length 4378mm, width 1810mm, height 1468mm, wheelbase 2705mm, minimum ground clearance 195mm, fuel tank capacity 53l. It is equipped with a 1.5l naturally aspirated engine, with a maximum horsepower of 122ps, maximum torque of 153nm, and maximum power of 90kw.
4
4
Share

What parts need to be replaced for engine misfire?

Engine misfire requires replacement of cylinder liners, pistons, etc. Causes of cylinder scoring: Severe piston misalignment, cylinder liner roundness and cylindricity tolerances exceeding allowable ranges, greatly reducing the sealing between pistons and cylinder liners. High-temperature gases in the cylinder leak downwards, destroying the oil film between pistons and cylinder walls, leading to cylinder scoring and poor break-in. Engine misfire: Engine misfire refers to insufficient power caused by engine failure, resulting in lack of power where a minority of cylinders in the total number are not functioning. Engine misfire shortens the lubrication oil usage cycle, easily causes sudden stalling, increases fuel consumption, produces black smoke, and results in power loss.
2
3
Share

How to Turn on the Car Air Conditioner for Cold and Hot Air?

Here are the methods to adjust the car air conditioner for cold and hot air: 1. There is a temperature adjustment knob on the car dashboard, with one side red and the other blue. Turning it all the way to the red side will produce hot air, while turning it all the way to the blue side will produce normal-temperature air. To get cold air, you also need to press the compressor magnetic (AC) switch to activate the cooling function. 2. Usually, first locate the temperature button. Above the temperature button, to cool, first turn on the AC switch and rotate towards the blue side to lower the temperature; for heating, there's no need to turn on the AC, just rotate towards the red side to increase the temperature. Gradually adjust the fan speed from 1 to 4. 3. Alternatively, press the AUTO mode, set the temperature, fan speed, and direction, and the system will automatically adjust the fan speed and temperature according to its built-in program.
5
2
Share

Can You Keep Driving When the Car's Water Temperature Is Too High?

You should not continue driving when the car's water temperature is too high. If the car's water temperature rises excessively, you should stop immediately and inspect the issue. Continuing to drive with high water temperature can cause: 1. The engine cylinder gasket to burn out due to overheating; 2. The engine may suffer from cylinder scuffing; 3. Prolonged driving can lead to deformation of the cylinder head and block, causing the engine to stall, piston scuffing, and crankshaft seizure, requiring a major engine overhaul; 4. In severe cases, the engine may be completely ruined. The optimal operating temperature for an engine is typically around 90 degrees Celsius. Common causes of high water temperature include: 1. Insufficient coolant; 2. Radiator leakage; 3. Cooling fan malfunction; 4. Thermostat failure; 5. Water pump failure.
6
0
Share

What is the difference between an independent ignition system and other ignition systems?

The differences between an independent ignition system and other ignition systems: 1. Different installation methods: The coil of an independent ignition system can be directly installed on the spark plug; other ignition systems cannot be directly installed on the spark plug. 2. Different ways to reach the spark plug electrodes: The voltage of an independent ignition system can directly reach the spark plug electrodes without going through a distributor or high-voltage ignition wires; other ignition systems need to pass through a distributor or high-voltage ignition wires to reach the spark plug electrodes. The ignition system is an important component of a gasoline engine, and the performance of the ignition system greatly affects the engine's power, fuel consumption, and exhaust emissions. All equipment that can generate an electric spark between the two electrodes of a spark plug is called the engine ignition system, which consists of a battery, generator, distributor, ignition coil, and spark plug.
11
1
Share

Which Direction to Turn the Spare Tire?

The lug nuts on passenger cars loosen in a counterclockwise direction: place your left hand facing the center of the tire, grip the wrench with your right hand and lift upwards to loosen the nuts. For large trucks, the lug nuts differ on the left and right sides - the left side (driver's side) has reverse threads while the right side has standard threads. This means tightening follows the vehicle's forward rolling direction, while loosening follows the reverse direction. Precautions before changing tires: Before changing a tire, first park the vehicle in a relatively safe and level location. Then engage the parking brake, shift into park, and turn the ignition to the "lock" position. Activate the hazard lights and place a triangular warning sign at a sufficient distance from the vehicle. Checking onboard tools: Next, inspect the onboard jack, tool kit, and spare tire. Depending on the vehicle model, spare tires are typically located: under the trunk floor, suspended beneath the rear of the vehicle, or mounted outside the trunk door.
4
1
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.