What is the wheelbase of the Lavida?

1 Answers
VonKendra
07/30/25 10:44am
The front wheelbase of the Lavida is 1517 mm, and the rear wheelbase is 1493 mm. Introduction to Wheelbase: Wheelbase refers to the distance between the center lines of the tracks left by the wheels on the vehicle's supporting plane (generally the ground). If there are dual wheels at both ends of the axle, the wheelbase is the distance between the center planes of the dual wheels. Generally speaking, the wider the wheelbase, the higher the driving comfort. Function of Wheelbase: Generally, a wider wheelbase provides higher driving comfort and better stability. When the vehicle tilts laterally, the outer wheels can offer better support. In curves, the vehicle's roll angle is smaller, and the limit of the outer wheels appears later. However, some domestic cars lack power steering, and if the front wheelbase is too wide, the steering wheel can feel very 'heavy,' affecting driving comfort. Additionally, wheelbase also influences the vehicle's total width, total weight, and safety.
Was this review help?
3
3
Share
More Forum Discussions

What Are the Consequences of Not Changing Antifreeze for a Long Time?

Antifreeze can expire over time, and expired antifreeze may develop impurities. Antifreeze Replacement Cycle: For vehicles that operate for extended periods, such as taxis, high-quality antifreeze should generally be replaced once a year. For vehicles with shorter operating hours, replacement can be done every two years or every 30,000 kilometers. To prevent excessive foam formation, which reduces the heat exchange efficiency between the antifreeze and engine components, ensure the product is within its validity period when adding it. Long-life antifreeze can last up to three years. If suspended particles, sediment, or signs of deterioration or discoloration are observed in the antifreeze, replace it promptly and clean the system. How to Determine a Lack of Antifreeze: Check the antifreeze warning light on the dashboard. If it lights up, it may indicate a lack of antifreeze, though it could also be due to excessively high cylinder temperatures. Inspect the antifreeze reservoir. If the fluid level is below the minimum mark (MIN), do not continue driving and add antifreeze promptly. Check the water level indicator on the antifreeze tank. The normal antifreeze level should be between the maximum and minimum marks. If the antifreeze level is below the minimum mark, it indicates a shortage.
1
3
Share

Which has higher viscosity between 0w40 and 5w40?

0w40 and 5w40 have the same viscosity. Both 5w-40 and 0w-40 are engine oil grades, where the letter W stands for Winter; the number 40 represents the high-temperature viscosity grade of the oil—the larger the number, the stronger the high-temperature viscosity of the oil. The numbers 5 and 0 indicate the minimum applicable temperature of the oil, or its low-temperature fluidity. 0 means the oil's minimum applicable temperature is -35 degrees Celsius, while 5 means it's -30 degrees Celsius. Below are the functions of engine oil: 1. Friction reduction: A sufficiently thick oil film separates the surfaces of relatively sliding parts, thereby reducing wear. 2. Sealing: Engine oil can form a seal between the piston rings and pistons, reducing gas leakage and preventing external contaminants from entering. 3. Rust prevention: Lubricating oil adheres to part surfaces, preventing contact with water, air, acidic substances, and harmful gases. 4. Cushioning: When the pressure in the engine cylinder rises sharply, suddenly increasing the load on the pistons, piston rings, connecting rods, and crankshaft bearings, this load is transmitted and lubricated through the bearings, cushioning the impact load. 5. Cleaning: Good engine oil can carry carbon deposits, sludge, and worn metal particles from engine parts back to the oil pan through circulation, washing away dirt generated on the working surfaces of parts as the oil flows.
16
5
Share

What kind of air is blown without AC?

Without AC, the air blown is natural air. Here is an introduction to the air conditioning system: 1. Buttons and components: The car AC button is the switch for the car air conditioning cooling system. Pressing the AC button will gradually lower the temperature inside the car. The car air conditioning cooling system consists of a compressor, condenser, receiver-drier, expansion valve, evaporator, and blower, among other components. These parts are connected by copper pipes and high-pressure rubber hoses to form a sealed system. 2. Function: The car air conditioning system can cool, heat, ventilate, and purify the air inside the cabin, providing a comfortable environment for passengers and reducing driver fatigue, thereby improving driving safety. It generally includes a cooling device, heating device, and ventilation device.
19
2
Share

Where is the output speed sensor of the 09g transmission located?

The output speed sensor of the 09g transmission is located at the upper front of the transmission. The automotive transmission is a set of gear-shifting devices used to coordinate the engine speed with the actual driving speed of the wheels, aiming to achieve optimal engine performance. The transmission can produce different gear ratios between the engine and wheels during vehicle operation. Below is an introduction to dual-clutch transmissions: 1. Dual-clutch transmissions come in two types: dry and wet. 2. A wet dual-clutch refers to a multi-plate clutch system where two sets of coaxial clutches (one large and one small) are installed together in a sealed oil chamber filled with hydraulic fluid. Thus, the wet clutch structure offers better adjustment capability and superior thermal performance, enabling it to transmit higher torque. 3. The dry dual-clutch was developed based on the technology of the 6-speed DQ250 wet dual-clutch, with simplified hydraulic systems. 4. The structure of a dual-clutch transmission is very similar to that of a manual transmission, featuring two sets of clutches responsible for shifting even and odd gears respectively, significantly improving shift speed.
14
0
Share

Is a Driving License Required for Car Paint Touch-Up?

Car paint touch-up requires leaving the driving license, and here are the specific reasons: 1. National requirements for vehicle repairs: Qualified shops performing sheet metal painting or repair projects are required by public security authorities to record vehicle information into the public security management system before proceeding with repairs. Failure to record the information in the system will result in corresponding liabilities, primarily to facilitate the tracing of hit-and-run vehicles or illegal activities such as smuggling and theft. Recording the information requires the vehicle's driving license, but the shop should return it promptly after recording. 2. Uploading vehicle information for post-accident repairs: If the paint job is covered by insurance and an immediate damage assessment cannot be made, and the owner is not present to wait, the owner may need to leave the driving license to facilitate the later upload of vehicle information. Many shops handling a high volume of accident vehicles will request the owner to leave the driving license and retrieve it together with the car after repairs. There are also cases where some repair shops retain the owner's driving license to manipulate insurance claims, but such practices are now rare.
5
2
Share

What are the design specifications for non-motorized vehicle ramps?

The ramp width should not be less than 0.30m, the slope should not exceed 1:5, and the ramp length should not exceed 6m. Below is an introduction to ramps: 1. Introduction: Refers to a uniformly inclined walkway or driveway. It serves as an inclined traffic passage connecting areas with elevation differences or floors, as well as vertical traffic and evacuation measures at entrances. 2. Content: When steps cannot be constructed due to usage or other reasons, ramps can be used to address height variations. Public green spaces and public buildings typically require barrier-free access, making ramps an essential element. Ramps are an important method for pedestrians to navigate elevation changes on the ground. 3. Application: Used in various public places such as residential thresholds, hotel corridors, convention centers, shopping malls, supermarket entrances, residential community gates, nursing homes, hospitals, train stations, airports, and more.
8
5
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.