What is the wheelbase of the Bestune X40?

How to Adjust the Idle Speed of a Car?

Car idle speed adjustment method: 1. After fully releasing the throttle handle, leave a certain amount of free play, install the air filter, ensure the performance of other components is intact, start the engine, let it warm up, and first open the choke; 2. Begin the adjustment by first screwing the air adjustment screw all the way in, then reversing it one turn, then adjust the throttle screw to ensure the engine can run at a certain speed even when the throttle handle is fully released; 3. Try to lower the idle speed first, reducing the engine speed as much as possible; 4. Then try to increase the idle speed, also adjusting the air adjustment screw, aiming to make the engine speed as high as possible; 5. Repeat these steps continuously, adjusting several times until you find a satisfactory idle speed.

17

0

Share

What to Do When the Wiper Makes Noise While Wiping the Windshield?

Car wiper noise while wiping the windshield and solutions are as follows: 1. Wiper aging: Due to aging, the rubber part of the wiper may wear off or fall off, causing noise during wiping due to friction. Wiper aging is a normal phenomenon, and it can be resolved by timely replacement. 2. Dry windshield: Using the wiper on a dry windshield without water can lead to noise due to lack of lubrication. Generally, avoid using the wiper on a dry windshield, as it accelerates wear and shortens the wiper's lifespan. 3. Debris on the windshield: If there are hard impurities like sand or small stones on the windshield, they can cause noise due to friction when the wiper operates. In such cases, clean larger debris from the windshield beforehand.

8

4

Share

Does the Avancier have a 7-seater option?

The Avancier does not have a 7-seater option; it is a 5-seater. Taking the 2020 Avancier as an example, it belongs to the midsize SUV category with body dimensions of: length 4585mm, width 1942mm, height 1670mm, a wheelbase of 2820mm, a trunk capacity of 510 liters, and a curb weight of 1708kg. The 2020 Avancier features a MacPherson strut front suspension and a multi-link independent rear suspension. It is equipped with a 1.5T turbocharged engine delivering a maximum horsepower of 193PS, maximum power of 142kW, and maximum torque of 243Nm, paired with a continuously variable transmission (CVT).

11

2

Share

Where is the VIN code located on a sedan?

Sedan VIN codes can be found in: 1. The left side of the instrument panel; 2. The lower left side of the windshield; 3. On the vehicle identification plate; 4. On the body at the upper part of the right front shock absorber; 5. In the trunk area; 6. On the door hinge pillar, door lock pillar, or one of the door edge pillars connected to the door lock pillar. A sedan's VIN consists of 17 characters, containing information about the vehicle's manufacturer, year, model, body type and code, engine code, and assembly location. The functions of the Vehicle Identification Number (VIN) are: 1. To confirm the vehicle's identity; 2. For traffic violation inquiries; 3. To check vehicle batches; 4. For precise parts lookup.

12

4

Share

How to Interpret the Guideline in the Rearview Camera?

You can interpret the guideline in the car's rearview camera as follows: 1. Red line: This can be regarded as a warning line, with the bottom of the line located 30 centimeters from the rear of the car. It is not advisable to continue reversing beyond this point. 2. Yellow line: This can be considered a deceleration line, with the bottom of the line 60 centimeters from the rear of the car. You can continue reversing but should slow down. 3. Green line: This can be seen as a safety line, with the bottom of the line positioned far from the rear of the car. You can continue reversing safely. If the rearview camera displays blue lines, don't be confused, as their meaning is essentially the same as described above. The line closest to the rear of the car is the warning line, and the car will prompt you to stop reversing.

10

0

Share

How to Replace the Taillight on a Lavida?

The method to replace the taillight on a Lavida is as follows: 1. The vehicle taillights are mainly located on both sides of the rear part of the car, with the fastening screws inside the vehicle; 2. Open the tailgate to find two plastic fastening buckles inside, and use tools to remove them; 3. Lift the interior trim panel to expose the fastening screws inside, then remove them directly; 4. When taking out the taillight, be careful not to damage the wiring harness, and properly store the old taillight; 5. Install the new taillight. Taking the 2021 Lavida as an example, it belongs to the compact car category, with body dimensions of length 4670mm, width 1806mm, height 1474mm, a wheelbase of 2688mm, and a fuel tank capacity of 51 liters.

14

4

Share

What is the wheelbase of the Bestune X40?

How to Adjust the Idle Speed of a Car?

What to Do When the Wiper Makes Noise While Wiping the Windshield?

Does the Avancier have a 7-seater option?

Where is the VIN code located on a sedan?

How to Interpret the Guideline in the Rearview Camera?

How to Replace the Taillight on a Lavida?

How to reset the tire pressure light on Roewe 360?

Where is the hazard warning flasher located in a Volkswagen?

What is the minimum ground clearance of a sedan?

How often does a vehicle need an annual inspection?