What is the wheel size of the 10th-generation Civic?

What does 280TGDI mean?

This is the rear emblem of a car. S5 stands for the 'model', 280 represents 'peak torque', and TGDI is the English abbreviation for the engine's highlight technologies, where T stands for turbocharging and GDI stands for gasoline direct injection technology. To put it in simpler terms, it refers to a turbocharged gasoline direct injection engine. Below is an introduction to TGDI: 1. As the most advanced powertrain system currently available, the TGDI engine combines cutting-edge technologies such as turbocharged intercooled TCI and gasoline direct injection GDI, offering numerous advantages including strong power and fuel economy. 2. This technology has now been widely adopted, with international automakers like Mercedes-Benz, BMW, General Motors, and Honda considering TGDI technology as a key competitive advantage in the future automotive market, investing in its development and utilization. 3. TGDI technology has also become an involuntary benchmark for measuring the technical level and R&D capabilities of international automotive companies.

20

5

Share

What Causes Engine Idle Stalling?

Here are the reasons for engine idle stalling: 1. Ignition system failure: Issues with components such as the ignition coil, ignition module, ignition ECU, distributor, ignition signal generator, sensors affecting ignition timing, or high-voltage wires can lead to misfires, weak sparks, or incorrect ignition timing, resulting in poor idle performance. 2. Neutral start switch circuit: In vehicles equipped with automatic transmissions, the ECU adjusts the idle speed based on signals from the neutral start switch. When the gear selector is in reverse or drive, the idle speed is automatically increased; otherwise, it is decreased. A faulty neutral start switch circuit can cause the ECU to receive incorrect signals, leading to excessively high or low idle speeds. 3. Fuel pump and fuel system: The fuel pump and fuel system affect fuel pressure. If the pressure is too low, the actual fuel injection volume decreases under the same energizing time of the injector coil, resulting in poorer spray quality and a lean idle mixture. Conversely, if the pressure is too high, excessive fuel injection occurs, leading to a rich mixture. Fuel system pressure is related to the technical condition of the fuel pressure regulator, fuel pump, fuel pressure solenoid valve, and their circuit operation.

13

5

Share

Which country does Nissan belong to?

Nissan Motor Corporation (NISSAN) is a Japanese automobile manufacturer established in 1933 in Yokohama, Kanagawa Prefecture. Currently, it has vehicle manufacturing bases in twenty countries and regions (including Japan) and provides products and services in over 160 countries and regions worldwide. Its main models include the Teana, Sylphy, X-Trail, and Qashqai. The Nissan logo features a circle representing the sun, with the Japanese phonetic characters for "Nissan" in the middle. The entire design symbolizes "the pursuit of a brighter future for people and automobiles." Key milestones in Nissan's development are as follows: 1933 – Japan Industries Co., Ltd. and Tobata Casting Co., Ltd. jointly registered "Automobile Manufacturing Co., Ltd." 1934 – "Automobile Manufacturing Co., Ltd." was renamed "Nissan Motor Co., Ltd." 1960 – Nissan established Nissan Motor Corporation in U.S.A. for sales operations. 2004 – Nissan's global sales reached 3.388 million vehicles.

7

2

Share

Do You Need to Press the Clutch When Shifting an Automatic Transmission?

Automatic transmission cars do not have a clutch mechanism, so there is no need to press the clutch when shifting gears. Currently, automatic transmissions mainly include hydraulic automatic clutches, CVT continuously variable transmissions, and DSG dual-clutch transmissions, whose structures are completely different from manual transmission clutches. The so-called semi-automatic transmission refers to AMT, which adds an automatic shifter to the manual clutch, meaning it can be understood as a manual clutch with automatic shifting. Below are the correct shifting methods for automatic transmission cars: 1. After starting the engine in P gear, no matter which gear (D, N, R) you want to shift into, you must first press the brake and then push the gear lever into the target gear. If you do not press the brake, the gear lever cannot be moved because the transmission is equipped with a safety lock mechanism. 2. If the vehicle shifts from N to D or R, you must also press the brake. At this time, the vehicle transitions from a stationary state to movement. If you do not press the brake, the vehicle will suddenly lurch forward (or backward), creating a safety hazard and causing significant damage to the vehicle's transmission components. 3. While driving, shifting from D to R requires pressing the brake, but shifting from D to sport mode S does not require pressing the brake. Similarly, shifting into manual mode does not require pressing the brake. When parking, shifting from N to P also requires pressing the brake; otherwise, the gear lever cannot be pushed up.

5

3

Share

What is a China V Vehicle?

China V vehicles refer to those that comply with the 'China V Emission Standard for Motor Vehicles'. The emission standards for motor vehicles are established to implement environmental protection laws, reduce and prevent pollution from vehicle exhaust, protect the ecological environment, and ensure human health. Here are methods to check the emission standard of a vehicle: 1. Look at the front windshield, where the vehicle's environmental protection label is usually clearly marked. 2. Visit the official website of the vehicle environmental protection department for inquiries. 3. Check the documentation provided by the dealer at the time of purchase, typically starting from the vehicle conformity page or the first page of the vehicle certification. 4. If unable to find the information, take the vehicle registration form or a copy to the vehicle management office for verification. 5. Make a rough estimation based on the year the vehicle was registered.

20

2

Share

Are Car OBD Fuel Savers Reliable?

OBD port fuel savers are reliable. Below is relevant information about OBD fuel savers: 1. The OBD fuel saver is a power and fuel optimization device (based on OBD protocol) that can adjust the vehicle according to the driver's habits, remap the car's ECU, and self-regulate. 2. OBD fuel savers can enhance and optimize the car's engine and power, as well as improve fuel efficiency, significantly aiding in reducing the vehicle's fuel consumption. 3. For brand-new cars that have just been purchased, there is no need to install an OBD port fuel saver. Since the car has already been adjusted to optimal parameters at the factory, adding an optimization device would be futile. Moreover, the adjusted data might affect the engine's normal operation, leading to insufficient power. In severe cases, it could even cause knocking or cylinder scoring. Therefore, installing an OBD port fuel saver is only suitable for older cars or those experiencing significant power loss.

9

5

Share

What is the wheel size of the 10th-generation Civic?

What does 280TGDI mean?

What Causes Engine Idle Stalling?

Which country does Nissan belong to?

Do You Need to Press the Clutch When Shifting an Automatic Transmission?

What is a China V Vehicle?

Are Car OBD Fuel Savers Reliable?

Are car coolant and antifreeze the same thing?

How to Avoid Stalling on a Hill Start?

What does the 'a' below the electronic handbrake mean?

Which engine oil is suitable for Civic?