···
Log in / Register

What is the weight of the Changan Oshan X7?

4 Answers
AaliyahAnn
07/30/25 1:56am

Oshan X7 has a curb weight of 1900-2075 kg. Below is the relevant introduction of Oshan X7: 1. Oshan X7 is equipped with a 1.5TGDI engine, delivering a maximum power of 178 horsepower and a maximum torque of 265N.m/1450-4500rpm. It is paired with a wet 7DCT automatic transmission. The vehicle dimensions are 4705/1860/1720mm in length/width/height, with a wheelbase of 2780mm. 2. Changan Oshan X7 features the OnStyle 2.0 Oshan intelligent connectivity system, 5G intelligent vehicle chip IMX8, "Eagle Eye" remote video system, ultra-high-definition 360° panoramic imaging, and a fully automatic parking system.

Was this review help?
12
1
Share
SanFernando
08/15/25 7:51am

I just checked the weight data of the Changan Oshan X7. Its curb weight is approximately 1,620 kg when empty, with slight variations depending on the configuration—lighter for base models and heavier for higher trims. As someone who has studied cars for years, I know that vehicle weight directly impacts driving feel—a heavier SUV feels more stable at high speeds, reducing body float or skidding, especially on mountain roads or windy days, which enhances safety. However, in city traffic, a heavier vehicle consumes more fuel when accelerating, leading to slightly higher fuel consumption compared to lighter cars. Additionally, the increased weight means the suspension system bears more load, so extra attention should be paid to brake pad wear during maintenance to avoid delayed braking. Overall, its moderate weight balances family travel space and daily practicality, making it a good reference for buyers who prioritize spacious interiors.

Was this review help?
6
3
Share
Expand All
MacStephanie
10/21/25 3:21am

I drove my friend's Changan Oushang X7 for a while, which weighs around 1,620 kg. I felt the power response was a bit sluggish when starting in the city, especially when the traffic light turns green—you need to press the accelerator harder, making it less agile compared to compact cars. However, it performs well on highways or when taking curves, offering good stability without much tail swing or body roll. Even when fully loaded with family or luggage, it remains steady. Fuel consumption is slightly higher than sedans, averaging 10-12L per 100 km, especially noticeable when using air conditioning in summer. The weight doesn’t cause much trouble when parking, as the steering is relatively flexible. Plus, the spacious body design makes it suitable for daily commutes or short trips. I’d recommend choosing the version based on your driving habits.

Was this review help?
20
1
Share
Expand All
KylieAnn
12/04/25 3:48am

I pay close attention to vehicle safety performance. The Changan Oshan X7 has a curb weight of around 1,620 kg, which is beneficial for body balance. It feels solid overall with strong rigidity, making it less prone to rollovers or loss of control. The weight helps distribute impact forces better to protect passengers, though braking distances may be slightly longer, requiring earlier deceleration. Daily driving weight also affects fuel economy, but for an SUV, this weight range is reasonable. During maintenance, it's advisable to check tires and suspension more frequently to avoid excessive wear. Overall, the weight design strikes a good balance between safety and practicality.

Was this review help?
13
0
Share
Expand All
More Forum Discussions

how to program car key transponder

Programming a car key transponder is a complex process that typically requires specialized diagnostic equipment and software. For most vehicle owners, the safest and most reliable method is to have it done by a professional locksmith or dealership. While DIY kits exist, they are often model-specific and may not work on all cars, especially newer models with advanced security systems. The process involves syncing the transponder chip's unique electronic code with the car's immobilizer system, a security feature that prevents the engine from starting without a recognized key. The general steps, which vary significantly by manufacturer, often involve: Having a blank transponder key that is correctly cut to match your car's locks. Using a diagnostic tool to access the car's programming mode, often through the OBD-II port. Following a precise sequence of actions (e.g., turning the ignition on and off, pressing buttons) within a specific time frame to register the new key. The table below outlines the key differences between professional and DIY approaches: Aspect Professional (Locksmith/Dealership) DIY Kits Success Rate Very High (uses professional-grade tools) Variable, highly model-dependent Cost $50 - $400+ (depending on car brand and location) $30 - $200 (for kit and key) Time Required Usually 30 minutes to 1 hour 30 minutes to several hours (with learning curve) Tools Needed Professional programmer, key cutter DIY programmer, pre-cut key Risk Factor Low (expertise minimizes risk of errors) High (potential to "lock" the immobilizer system) Best For All vehicles, especially newer or luxury models Older models with simpler systems, tech-savvy owners Attempting this yourself on a modern car can sometimes cause the immobilizer to reject all keys, requiring an expensive tow and dealership reset. The cost of professional programming is often justified by the assurance it's done correctly, preserving your vehicle's security.
9
0
Share

how to program a key fob for a car

Programming a key fob for your car typically involves one of three methods: an onboard procedure you can do yourself, a trip to a dealership, or using specialized diagnostic tools. The simplest method is an onboard programming sequence , which is often detailed in your vehicle's owner's manual. This process usually requires a working key and involves a specific sequence of turning the ignition on and off and pressing buttons on the fob within a set time window. However, this self-service option is not available for all car models, especially many newer vehicles with advanced security systems. For cars with more complex encryption, dealer or locksmith programming is necessary. A dealership will use proprietary software to synchronize the new key fob's unique code with your car's immobilizer system. While this is the most reliable method, it is also the most expensive. An independent auto locksmith with the right diagnostic tools can often perform the same service at a lower cost. The feasibility and cost largely depend on your car's make, model, and year, as shown in the table below. Car Type Typical DIY Availability Average Dealer Programming Cost Average Locksmith Cost Key Notes Older Domestic (pre-2010) High $50 - $100 $30 - $80 Often simple onboard procedure. Modern Economy Sedan Medium $100 - $250 $70 - $150 Some may allow DIY, many require a pro. European Luxury Sedan Low $200 - $500 $150 - $400 Almost always requires professional tools. New EV / Hybrid Very Low $150 - $400 $120 - $350 High security; dealership often required. Truck/SUV (2015+) Medium $100 - $300 $80 - $200 Varies significantly by brand. Before anything, confirm you have a programmable key fob . Blank fobs bought online must be compatible with your Vehicle Identification Number (VIN). The safest first step is always to check your owner's manual or contact a local locksmith for a quote and to verify the correct procedure for your specific vehicle.
14
4
Share

how to neutralize road salt on car

The most effective way to neutralize road salt on your car is through immediate and thorough washing, with a specific focus on the undercarriage. Road salt accelerates rust and corrosion by facilitating electrochemical reactions on your car's metal surfaces. To stop this, you need to physically remove the salt and neutralize its corrosive effects. Immediate Action is Critical As soon as temperatures rise above freezing, head to a touchless car wash that includes a dedicated undercarriage spray . This is non-negotiable during winter. The high-pressure spray is the best way to blast away salt from hard-to-reach areas like frame rails, suspension components, and brake lines. Simply rinsing the visible body panels is not enough. The Neutralizing Wash Process After the initial undercarriage rinse, use a dedicated car wash soap (not household dish detergent, which can strip wax) in a two-bucket method to prevent swirling the paint with grit. Pay close attention to the lower third of the car, wheel wells, and behind the wheels where salt spray accumulates. The Final, Crucial Step: Sealing the Surface Washing removes the salt, but to truly neutralize the threat, you need to protect the paint. After a thorough drying with a microfiber towel, apply a quality spray wax or sealant . This creates a protective barrier that makes it harder for salt and grime to bond to the paint the next time you drive. For the ultimate protection, a semi-permanent ceramic coating applied professionally can provide seasons of defense. For a quick comparison of protection methods: Protection Method Application Frequency Estimated Cost (DIY) Key Benefit Spray Wax Every 2-4 weeks $15 - $25 Quick application, good beading Liquid/Paste Wax Every 2-3 months $20 - $50 Deep gloss, longer-lasting than spray Paint Sealant Every 6 months $25 - $60 Superior durability and chemical resistance Ceramic Coating 2-5 years (professional) $500 - $2000+ Extreme hardness, best overall protection
19
5
Share

how to put on a car window sticker

Applying a car window sticker correctly is a simple process that hinges on thorough cleaning and the "soapy water method" to allow for easy positioning. The key is to create a temporary slip layer between the adhesive and the glass, enabling you to slide the decal into the perfect spot before squeezing out the liquid for a permanent, bubble-free bond. First, gather your materials: the sticker, a spray bottle with a mixture of a few drops of dish soap and water, a squeegee (or a credit card), and a microfiber cloth. Clean the window meticulously with glass cleaner and dry it completely. Any dust or dirt trapped under the vinyl will be permanent. Now for the application. Peel the paper backing off the sticker, leaving the graphic on the application tape. Liberally spray the soapy water onto the clean, dry glass . Also, spray the adhesive side of the sticker . This wet layer is what gives you the freedom to move it around. Carefully place the sticker onto the wet window. You can now slide and adjust it until it's perfectly aligned. Once positioned, start at the center and use the squeegee to firmly push the water and air bubbles out toward the edges. Work methodically from the center out. Be firm to ensure full adhesion. After you've squeegeed the entire surface, slowly peel off the application tape at a sharp angle. If any small corners lift, press them back down. Finally, use the dry microfoth cloth to wipe away any excess moisture from around the edges. Let it cure for 24-48 hours before washing the car. For a quick reference, here are the key variables in the soapy water mixture and their effects: Factor Recommendation Effect on Application Soap-to-Water Ratio 4-5 drops of dish soap per 16oz water Provides optimal slip without hindering final adhesion. Water Temperature Lukewarm Helps soap mix effectively; cold water can reduce slip. Squeegee Pressure Firm, even pressure Essential for removing all liquid and preventing bubbles. Curing Time 24 hours (min) / 48 hours (ideal) Allows adhesive to fully bond before exposure to moisture. Application Temperature 50°F - 90°F (10°C - 32°C) Ensures adhesive and vinyl are pliable for best results.
14
3
Share

how to look up parts by vin number

Looking up parts by your car's VIN (Vehicle Identification Number) is the most accurate method to ensure compatibility. The VIN is a unique 17-digit code that acts as your car's fingerprint, containing specific details about its manufacturer, model, year, engine, trim, and place of production. Using it to search for parts eliminates the guesswork and prevents ordering incorrect components that might not fit, even for the same car model from a different model year. The best places to perform a VIN lookup are directly through official dealership parts departments or reputable online auto parts retailers. Websites like AutoZone, Advance Auto Parts, RockAuto, and OEM (Original Equipment Manufacturer) sites have dedicated VIN search tools. You simply enter the full VIN, and the site filters its catalog to show only parts designed for your specific vehicle. Here’s a typical breakdown of the information encoded in a VIN, which explains why it's so precise: VIN Position What It Typically Encodes Example Data for a 2021 Ford F-150 1-3 (WMI) Country of origin and manufacturer 1FT (USA, Ford Motor Company) 4-8 (VDS) Vehicle attributes (model, body style, engine) FW1E5 (F-150, 4x4 SuperCrew, 3.5L EcoBoost) 9 (Check Digit) Security code to verify VIN authenticity 2 10 (Model Year) The year the vehicle was manufactured L (2021) 11 (Plant Code) Specific assembly plant M (Michigan Truck Plant) 12-17 (VIS) Unique production serial number 123456 To get started, locate your VIN. It's most commonly found on the dashboard near the windshield on the driver's side, on the driver's side doorjamb, or on your vehicle's title and insurance documents. Ensure you copy it correctly, as a single wrong character will lead to inaccurate results. While VIN lookup is highly reliable, always double-check the part number and description against your vehicle's manual or a trusted mechanic for critical components like engine control units or airbags.
9
3
Share

how to know if a car has insurance

The most direct way to know if a car has valid insurance is to ask the driver for their proof of insurance card . In the US, this is a small document issued by the insurance company that must be carried in the vehicle at all times. It lists the policy number, effective dates, and the insured vehicle. If you're considering buying a used car, the seller should provide this information, but you must verify it independently. For a more official verification, you can check the insurance status through your state's Department of Motor Vehicles (DMV) database. This is often linked to the vehicle's license plate or registration. Many states have electronic verification systems where law enforcement can instantly check insurance status during a traffic stop. As a private individual, your access might be limited, but you can often use online DMV services to verify insurance if you have a legitimate reason, like finalizing a sale. When you're driving, a visual clue is the insurance verification sticker on the license plate or windshield, required in some states. However, this is not universal. The most reliable method remains reviewing the physical or digital insurance card. The table below outlines common verification methods and their reliability. Verification Method How It Works Reliability Key Details Proof of Insurance Card Physical or digital card from the insurer. High Must show current effective dates. DMV Database Check Electronic verification via state system. Very High Tied to registration; most official method. Insurance ID Sticker Physical sticker on plate/windshield (state-specific). Medium Not all states use this system. Calling the Insurer Contact the company with VIN and owner's permission. High Confirms active policy directly. Bill of Sale Clause Seller provides proof at time of purchase. Medium Must be verified immediately. Remember, never assume a car is insured. Always get proof before driving a new purchase or if you're in an accident. If you're hit by another driver, politely ask for their insurance card and take a picture of it.
3
2
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.