What is the warranty period for the 2012 Focus dual-clutch transmission?

1 Answers
VanMelanie
07/29/25 11:51pm
Generally, the warranty period for the clutch is 1 year, but it varies depending on the vehicle model. Ford Introduction: The classic Focus, although a family sedan, boasts a race-grade chassis and full independent suspension system that surpasses its peers, delivering smooth and sharp cornering performance. It has earned the reputation of "King of Corners." Paired with a 1.8L all-aluminum reverse-flow engine and an advanced gear-shifting system, it instantly delivers abundant power. Ford Engine: The new Focus is equipped with a 2.0-liter GDI naturally aspirated direct-injection engine featuring Ti-VCT variable timing system, which is the first non-turbocharged engine with fuel direct-injection technology introduced by Ford in China. The fuel direct-injection technology allows each cylinder to intake more air during every working cycle, while fuel is injected directly into the cylinder at a high pressure of 200Bar, achieving better atomization effects.
Was this review help?
3
0
Share
More Forum Discussions

What is the break-in period for a motorcycle in kilometers?

The break-in period for a motorcycle is 500 kilometers. After each new motorcycle leaves the factory, due to the small clearance between engine components and rough moving surfaces, a break-in process is required to achieve optimal fit between gears, pistons and cylinders, shafts and bearings, etc. Precautions during the break-in period: During the break-in period, the maximum speed should be controlled. Generally, the driving speed should be kept below 60 km/h with variable speeds, avoiding prolonged driving at the same speed. It is advisable to drive at different speed ranges appropriately. Try to avoid carrying passengers or cargo during the break-in period: For motorcycles with gears, frequent gear shifting is recommended. After driving 1,000 kilometers, it is advisable to run at high speeds under safe conditions. Note that high-speed runs should be done before and after oil changes. During the break-in period, it is important to avoid aggressive throttle operation, sudden acceleration, and prolonged high-load driving. Applying some load appropriately can help components fit better. There is no need to be overly cautious, as this may not be beneficial for the motorcycle.
20
1
Share

Will the 12123 vehicle moving service call the car owner?

The traffic management 12123 system will automatically compare the information in the vehicle information database and then call the car owner to notify them to move the vehicle. Introduction to the one-click vehicle moving function: The one-click vehicle moving function is a convenient service launched by the 12123 traffic management department. It operates 24 hours a day. When you need to move a vehicle, by using this function, the 12123 system will automatically compare the information in the vehicle information database. Then, it will automatically query and retrieve the vehicle owner's mobile phone number in the background, and the system will send a vehicle moving notification to the vehicle owner via SMS or APP message push. Privacy protection: The two parties involved will not communicate directly, and their phone numbers will not be disclosed, ensuring full privacy protection and security. The one-click vehicle moving service on the 12123 platform can be applied for up to five times per month. Of course, if you encounter difficulties in operation or urgently need to contact the car owner, you can also inquire about the vehicle information at the vehicle management office to get in touch with the owner.
20
3
Share

Why is the tractor emitting white smoke?

The reasons for a tractor emitting white smoke are as follows: White smoke emission: When the diesel engine has delayed fuel injection, low injection pressure, or poor atomization, it can lead to white smoke emission. During cold starts in winter, white smoke from the exhaust pipe is normal and will gradually disappear after running for a while. Poor atomization of the fuel injector: Poor atomization causes incomplete combustion of diesel, resulting in white smoke. Repairing the fuel injector can solve this issue. Low cylinder pressure: Some diesel fuel turns into oil vapor without being burned, leading to white smoke from the exhaust pipe. Damaged cylinder gasket: If the engine has been used for a long time, the cylinder gasket may be damaged or the cylinder itself may be worn out, allowing coolant to enter the cylinder. In this case, replace the cylinder gasket and tighten the cylinder head bolts strictly in order using a torque wrench. It could also be due to uneven contact between the cylinder head and the cylinder block after prolonged use, requiring the cylinder surface to be ground flat with specialized equipment.
4
0
Share

Do I still need to display the vehicle inspection sticker in 2021?

Yes, it is required. According to the Road Traffic Safety Law of the People's Republic of China, it is illegal for motor vehicles to operate on roads without displaying license plates, annual inspection stickers, insurance stickers, or carrying the vehicle registration certificate and driver's license. Placement location: The vehicle inspection sticker must be affixed to the upper right corner of the windshield in a position that does not obstruct the driver's view. Replacement method: If the sticker becomes damaged or lost, you must visit the vehicle management office or traffic management department of the public security authority, or use the traffic management mobile app "12123" to apply for a replacement.
20
0
Share

Does a car purchased in 2015 need to undergo inspection in 2021?

A car purchased in 2015 needs to undergo inspection in 2021. Inspection of automotive components: Check whether the engine, chassis, body, and auxiliary equipment are clean, complete, and functional; whether the paint surface is uniform and aesthetically pleasing; whether any major assemblies have been replaced; and whether these conditions match the initial inspection records. Inspection of automotive functions: Verify whether the vehicle's braking performance, steering control, lighting, exhaust emissions, and other safety features comply with the requirements of the "Technical Conditions for Safe Operation of Motor Vehicles." Inspection for modifications: Check whether the vehicle has undergone any modifications, alterations, or transformations; whether the driving license, license plate, and all vehicle registration records match the actual condition of the vehicle; and whether any changes have been properly approved and documented with the relevant authorities.
3
4
Share

Does a car need antifreeze?

Yes, a car needs antifreeze, and it is essential to use the same brand of antifreeze when adding it. Different brands of antifreeze may have varying production formulas, and if mixed, multiple additives could undergo chemical reactions, rendering them ineffective. The method for replacing antifreeze is as follows: Before completely replacing the antifreeze, conduct a thorough inspection to check for any signs of leakage or cracks in the pipelines, with a particular focus on the five-way water pipe. Antifreeze flows through the five-way pipe and is then distributed to different parts of the car to function. If there is any leakage of antifreeze in this section, the water pipe should be replaced or the connection re-secured as needed. Drain the old antifreeze, then flush the liquid channels with clean water. Add clean water to the antifreeze reservoir, then continue to pour water into the reservoir to allow it to flow continuously through the engine cooling system. Start the engine and let it idle for 3 to 5 minutes to circulate the water. The water initially flowing out of the reservoir will have a faint pink color. Continue adding clean water until the water coming out is clear. Note: Do not forget to remove the heater hose and drain the water from the heater core. After draining for about an hour, add the new antifreeze through the radiator hose. Then, pour another bottle of antifreeze into the antifreeze reservoir until it is nearly full. Start the engine and let it run for about 10 minutes. At this point, the coolant level will drop slightly as air is expelled from the cooling system. Add more antifreeze until the reservoir reaches the maximum mark "MAXT."
13
1
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.