What is the wading depth of the VV7?

2 Answers
LeOlive
07/29/25 12:32am
The maximum wading depth of the VV7 is 350mm. The wading depth of the VV7 is determined by the height of the vehicle's chassis, which is the ground clearance listed in the model's parameter configuration. Generally, the greater the ground clearance, the higher the chassis, and the higher the safety factor when driving through waterlogged roads. Therefore, in terms of safe wading depth, off-road vehicles and SUVs have obvious advantages. However, for most compact and small vehicles with low chassis, the position of the vehicle's air intake should be used as a reference when passing through waterlogged roads. If the air intake of the VV7 is below the water level during wading, water will be sucked into the engine's cylinders. Since water cannot be compressed like air, it can cause severe damage to the engine's mechanical components (such as connecting rods, pistons, crankshafts, etc.). Therefore, the wading depth should not exceed the height of the engine's air intake. Installing a snorkel can also increase the height of the engine's air intake, thereby improving the maximum wading depth. If wading is unavoidable, the following safe and correct operations should be performed: Before driving through water, always turn off the auto start-stop function to prevent the engine from automatically restarting if the vehicle stalls in water, which could cause severe damage due to water ingestion. Assess the underwater road conditions based on the passage of vehicles ahead and choose an appropriate entry point. Observe the path taken by other vehicles and follow their tracks at a low speed, avoiding sudden acceleration or deceleration. On roads prone to water accumulation, use warning water level markers, trees, or reference points like the wheels and doors of other vehicles to estimate the water depth before deciding whether to proceed. Know your vehicle's safe wading depth. If the water depth exceeds half the height of the tires or the engine's air intake, avoid entering the water and choose an alternative route instead.
Was this review help?
5
0
Share
Ibarra
08/12/25 4:46am
I think the WEY VV7 doesn't have an officially announced exact wading depth, but similar city SUVs are generally around 400mm. The position of the air intake is a key factor, as it affects whether water enters the engine. The VV7 has a relatively high chassis design, so it can handle ordinary water accumulation, but don't push it too deep. I've driven through heavy rain and water accumulation before and really didn't dare to venture too far; if the water exceeds the height of the wheels, the engine could get flooded and be ruined, not to mention the risk of short circuits in the electronic systems. When wading through water, drive slowly at low speed, avoid sudden acceleration or braking to prevent splashing water too high. Afterward, check if the air filter is damp and replace it promptly. These tips can help avoid unexpected repair costs—everyone should stay safe.
Was this review help?
10
3
Share
Expand All
More Forum Discussions

Where is the Three-Way Catalytic Converter Located in the Engine?

The three-way catalytic converter is generally installed in the first bulge of the exhaust manifold under the car chassis, resembling a long kettle-shaped device. Here are the functions of the three-way catalytic converter: 1. The three-way catalytic converter is designed to process harmful gases such as CO, HC, and NOx emitted from the vehicle's exhaust. 2. Through oxidation and reduction reactions, these harmful gases are converted into harmless carbon dioxide, water, and nitrogen, thereby purifying the vehicle's exhaust. The working principle of the three-way catalytic converter is as follows: 1. When the engine exhausts gases through the exhaust pipe, CO, HC, and NOx pass through the catalyst in the three-way catalytic converter, which enhances the activity of these gases, facilitating oxidation-reduction chemical reactions. 2. Among them, CO is oxidized into colorless, non-toxic carbon dioxide gas at high temperatures, HC compounds are oxidized into water (H2O) and CO2, and NOx is reduced into nitrogen (N2) and oxygen (O2).
6
3
Share

What are the characteristics of engine cylinder scuffing?

Engine cylinder scuffing has the following characteristics: 1. Normally, the vehicle's power significantly decreases. 2. Abnormal water temperature, the vehicle shows high temperature or even boils shortly after starting. 3. Increased exhaust gas, with blue smoke from the rear exhaust. 4. Abnormal noises during engine operation. 5. The vehicle experiences misfiring or cylinder cut-off after idling for too long or driving for a short time. The main causes of engine cylinder scuffing include the following aspects: 1. The fit clearance between the piston and cylinder is too small. 2. The piston ring end gap is too small. 3. Piston ring breakage. 4. The piston and piston rings tilt to one side, pressing tightly against the cylinder wall. 5. Long-term poor atomization of the fuel injector or carburetor. 6. Faulty piston cooling nozzle. 7. Poor engine cooling or operation at too low temperatures.
4
5
Share

How to Use Hill Start Assist in a Car?

To use the hill start assist function in a car, follow these steps: 1. Ensure the gear lever is not in the P position (for automatic transmission models) and do not press the accelerator pedal. 2. The vehicle must be in a stationary state. 3. The driver should not engage the handbrake (foot brake or electronic brake). 4. When all the above conditions are met, the driver can release the foot from the brake pedal, and the hill start assist system will activate. Additional information: 1. Hill start assist control prevents the vehicle from rolling backward, allowing the driver to start the car easily and operate the pedals calmly. 2. Hill start assist is a function developed based on the ESP system, enabling the vehicle to remain braked for a few seconds after the driver releases the brake pedal, even without using the handbrake, when starting on a slope.
17
3
Share

Is Engine Oxidation Normal for a New Car?

Engine surface oxidation is a normal phenomenon. For imported cars, engine oxidation is common as vehicles are typically transported from overseas to China via sea freight. The air and seawater at sea contain high salt content, which inevitably adheres to the car during transportation, causing some corrosion and leading to engine oxidation. Here is more information about car engine oxidation: 1. The engine casing is usually made of cast iron or aluminum alloy, which undergoes slow oxidation when exposed to air. This oxidation has almost no impact on the engine's performance throughout its lifespan. 2. In fact, surface oxidation of the engine only forms an oxide film, which protects the engine. No special treatment is required; simply keeping the engine surface clean is sufficient. 3. To prevent engine oxidation, you can purchase high-quality antifreeze from the market.
14
0
Share

Is It Harmful to Press the Clutch in Neutral Gear?

Pressing the clutch in neutral gear can damage the car. Here are the reasons why pressing the clutch in neutral gear is harmful: 1. When the clutch pedal is pressed, it activates certain components of the vehicle. The force applied to the clutch pedal pulls the connecting rod, which then transfers the force through the fixed pin to the end of the connecting rod, and finally to the rear end where it contacts the release bearing. This force pushes the release bearing forward, engaging with the clutch disc, effectively putting the clutch in a semi-engaged state. 2. The component most severely affected by frequent use is the clutch release bearing, as it directly contacts the driven plate and is rotated by it. Over time, it may become loose due to wear or seize up due to insufficient lubrication.
5
5
Share

What is the difference between drum brakes and disc brakes?

1. Structural comparison: The principle of drum brakes is to add pistons inside the brake drum, which are pushed by hydraulic pressure to press against the brake drum, generating friction to achieve the braking effect. On the other hand, disc brakes apply hydraulic pressure to the caliper, causing the friction material to clamp the brake disc, thereby achieving the braking effect. 2. Principle comparison: The principle of drum brakes involves hydraulic pressure pushing the pistons, causing the brake shoes on both sides to press against the inner wall of the wheel, thus achieving the braking effect. Due to the forward motion of the wheel, the rolling force generated will react on the brake drum, amplifying the braking force, which affects ride comfort. In contrast, disc brakes use a hydraulic pump to push the brake caliper, thereby applying force to the brake pads to achieve the braking effect. Therefore, the braking force directly depends on the pressure of the brake caliper and is not amplified like drum brakes, resulting in inherently smaller braking force. 3. Advantage comparison: Drum brakes provide greater braking force, allowing for timely stopping in emergencies and effectively avoiding accidents. Due to the large inertia of heavy trucks, which require higher braking strength, drum brakes have an irreplaceable position in heavy trucks. Disc brakes, being an external braking system, offer good heat dissipation and easy control, allowing for high-frequency intermittent braking and integration with ABS intermittent braking.
9
0
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.