What is the wading depth of the Trumpchi GS4?

2 Answers
PaisleeLee
09/03/25 6:56am
The wading depth of the Trumpchi GS4 is 400mm. The wading depth of the Trumpchi GS4 is determined by the height of the vehicle's chassis, which is the ground clearance listed in the model's parameter configuration table. Generally, the greater the ground clearance, the higher the chassis, and the higher the safety factor when passing through waterlogged roads. Therefore, in terms of safe wading depth, off-road vehicles and SUVs have obvious advantages. However, for most compact cars and small cars with low chassis, the position of the vehicle's air intake should be used as a benchmark when passing through waterlogged roads. If the air intake of the Trumpchi GS4 is below the water level during wading, water will be sucked into the engine's cylinders. Since water cannot be compressed like air, it will cause severe damage to the engine's mechanical structure (connecting rods, pistons, crankshaft, etc.). Therefore, the wading depth must not exceed the height of the engine's air intake. The height of the engine's air intake, and thus the maximum wading depth, can also be increased by installing a snorkel. If wading is unavoidable, the following safe and correct operations should be performed: Before the vehicle enters the water, the auto start-stop function must be turned off to prevent the vehicle from automatically restarting after stalling in the water, which could cause severe damage if water enters the engine. Judge the underwater road conditions based on the passage of the vehicle ahead and choose a suitable entry point. Observe the path taken by other vehicles and follow their tracks at low speed, avoiding sudden acceleration or deceleration. On roads prone to water accumulation, observe warning water level markers, trees, and other reference points such as the wheels and doors of other vehicles to estimate the water depth before deciding whether to proceed. Know your vehicle's safe wading depth. If the water depth exceeds half the height of the tires or the engine's air intake, do not enter the water recklessly; choose an alternative route instead.
Was this review help?
17
3
Share
OSimon
09/15/25 8:16am
Regarding the wading depth of the Trumpchi GS4, I've driven this car for a while and know many people are concerned about whether it can handle deep water during the rainy season, but the official hasn't provided specific numbers. Generally speaking, the wading depth of this type of urban SUV is around 300 to 400 millimeters, roughly meaning the water level shouldn't exceed the center of the wheels. Otherwise, water entering the engine intake could cause serious problems. I remember one time when I drove through deep water, it was too high, and the electrical circuit shorted out, costing me thousands in repairs. If you really need to wade through water, you should first assess the water conditions, drive slowly, avoid sudden acceleration to prevent splashing water onto critical components. After wading, check the air filter and undercarriage wiring to avoid rust and corrosion. Overall, this car isn't suited for hardcore off-roading but handles daily road conditions fine. Safety first.
Was this review help?
19
1
Share
Expand All
More Forum Discussions

How to Reset the Tire Pressure on a Land Rover Range Rover?

Method to reset the tire pressure on a Land Rover Range Rover: First, adjust the tire pressure to light load in the settings on the dashboard. After setting it to light load, inflate the front tires to 2.3 bar and the rear tires to 2.5 bar. Then drive for a while. If no fault is reported, the tire pressure is normal, and the reset is complete. The Land Rover Range Rover has a length of 5000 mm, width of 2073 mm, height of 1869 mm, wheelbase of 2922 mm, front track of 1693 mm, rear track of 1685 mm, and minimum ground clearance of 220 mm. It is a mid-to-large SUV equipped with full-time four-wheel drive.
15
4
Share

What does a faucet symbol in the car indicate?

A faucet symbol in the car indicates the engine malfunction indicator light. When this light illuminates, it signifies that the engine has encountered a fault. If the engine malfunction light comes on while driving, it is likely due to poor combustion conditions in the engine, which may result from issues such as engine knocking or carbon buildup. This could be caused by the use of low-quality fuel or internal engine contamination, leading to the illumination of the engine malfunction light. Once the engine malfunction light is on, it will not disappear automatically. The engine fault signal is emitted by the ECU (Engine Control Unit), which controls all the electronic components of the engine. When the engine malfunctions, components such as the electronic throttle, fuel injectors, alternator, and fuel pump may be affected, causing the engine to operate abnormally.
7
4
Share

Will I get points deducted for driving at 50 in a 30 speed limit zone?

Driving at 50 in a 30 speed limit zone will not result in points deduction. According to the guidelines on traffic violations, driving a motor vehicle in violation of speed limits without causing any consequences will result in a warning from the traffic management department of the public security authorities: 1. Exceeding the speed limit by less than 50% on roads with a speed limit below 60 kilometers per hour; 2. Driving medium-sized or larger passenger or cargo vehicles, school buses, or hazardous chemical transport vehicles at speeds exceeding the limit by less than 10% on roads other than highways or urban expressways; 3. Driving vehicles other than medium-sized or larger passenger or cargo vehicles, school buses, or hazardous chemical transport vehicles at speeds exceeding the limit by less than 10%; 4. Driving a motor vehicle on a highway at a speed less than 20% below the prescribed speed limit.
3
3
Share

How to Determine When Car Brake Pads Need Replacement

Methods to check if car brake pads need replacement: 1. The vehicle dashboard has a brake pad wear limit warning light; generally, when this light comes on, it reminds the owner to replace the brake pads. 2. The thickness of brake pads is between 1 to 1.5 cm (may vary by manufacturer). When the wear thickness is less than 3 mm, the brake pads should be replaced promptly. 3. If there is brake caliper leakage, contaminating the brake pads and soaking into them, and oil stains are still found after sanding with sandpaper, the pads must be replaced regardless of thickness. 4. A decrease in brake fluid in the brake fluid reservoir. 5. Hearing a squeaking sound when braking is a reminder for the owner to replace the brake pads promptly.
6
3
Share

What is the method for adjusting the height of car lights?

Method for adjusting the height of car lights: Low beam: Position the car vertically facing a wall, about 1 meter away. Adjust the low beams so that both lights are at the same height. Mark two focal points on the wall, with the distance between them approximately equal to the distance between the car's headlights. Slowly reverse the car and observe if the center points shift. Adjust so that the two points always align with the marks. High beam: Position the car vertically facing a wall, about 1 meter away, ensuring both lights are at the same height. Mark two focal points on the wall, with the distance between them approximately equal to the distance between the car's headlights. Slowly reverse the car and adjust so that the two points gradually converge towards the center. At a distance of about 30 to 100 meters, they should merge into a single point. High beams can focus more intensely at 30 to 100 meters, illuminating farther distances with less divergence.
4
5
Share

How many chances are there for each driving test subject two exam?

Each driving test subject two exam has five chances, including one initial exam and one make-up exam on the spot if failed, totaling up to 10 exam opportunities. According to traffic laws, if an applicant cannot attend the exam at the scheduled time, they must apply to cancel the appointment one day in advance. Subject two, also known as the small road test, is part of the motor vehicle driver's license assessment and is the abbreviation for the field driving skills test subject. The C1 and C2 car test items include five mandatory tests: reversing into a garage, parallel parking, stopping and starting on a slope, turning at a right angle, and driving on a curve. Subject two has a full score of 100 points, with evaluation criteria set for disqualification, deduction of 20 points, deduction of 10 points, and deduction of 5 points.
15
1
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.