What is the wading depth of the Sagitar?

1 Answers
McGenesis
07/30/25 5:00am
The wading depth of the Sagitar is 300mm. The wading depth of the Sagitar is determined by the height of the vehicle's chassis, which is the ground clearance listed in the model's parameter configuration table. Generally, the greater the ground clearance, the higher the chassis, and the higher the safety factor when passing through waterlogged roads. Therefore, in terms of safe wading depth, off-road vehicles and SUVs have obvious advantages. However, for most compact and small cars with low chassis, the position of the vehicle's air intake should be used as a benchmark when passing through waterlogged roads. If the air intake of the Sagitar is below the water level during wading, water will be sucked into the engine's cylinders. Since water cannot be compressed like air, it can cause severe damage to the engine's mechanical components (such as connecting rods, pistons, crankshafts, etc.). Therefore, the wading depth should not exceed the height of the engine's air intake. The height of the engine's air intake, and thus the maximum wading depth, can also be increased by installing a snorkel. If wading is unavoidable, the following safe and correct operations should be performed: Before the vehicle enters the water, always turn off the auto start-stop function to prevent the engine from automatically restarting after stalling in the water, which could cause severe damage due to water ingestion. Assess the underwater road conditions based on the passage of vehicles ahead and choose an appropriate entry point. Observe the paths taken by other vehicles and follow their tracks at low speed, avoiding sudden acceleration or deceleration. On roads prone to water accumulation, use warning water level markers, trees, or the wheels and doors of other vehicles as reference points to estimate the water depth before deciding whether to proceed. Be aware of your vehicle's safe wading depth. If the water depth exceeds half the height of the tires or the engine's air intake, do not proceed and consider an alternative route.
Was this review help?
2
4
Share
More Forum Discussions

How to Open the Passenger Door of a Ferrari?

Ferrari passenger door opening method: The butterfly doors do not have obvious handles. You need to pull upward from the lower side of the door to open it. Ferrari is a renowned manufacturer of racing and sports cars, headquartered in Maranello, Italy, primarily producing Formula 1 race cars, competition vehicles, and high-performance sports cars. The Ferrari 488 is positioned as a mid-size sports car, with dimensions of 4605mm in length, 1975mm in width, and 1206mm in height, a wheelbase of 2650mm, and seating for two. In terms of interior design, this model largely continues the 468's design philosophy, featuring a black-and-red color scheme that exudes wild passion. Additionally, the gear shift buttons adopt a completely new design style.
16
0
Share

What Causes the Malfunction Light to Illuminate and Lack of Power When Accelerating?

The reasons for the malfunction light illuminating and lack of power when accelerating may include a faulty oxygen sensor or substandard fuel quality. When the engine malfunction light comes on, it indicates that the engine parameters have changed, with poor fuel combustion being the primary cause of these parameter variations. The engine malfunction signal is issued by the ECU, which controls all electronic components of the engine, such as the electronic throttle, fuel injectors, fuel pump, etc., covering various systems including intake, fuel, and ignition. After the engine malfunction light illuminates, it is essential to safely pull the vehicle over to the roadside, turn on the hazard warning lights, place a warning triangle 100 to 150 meters behind the vehicle, and contact a relevant repair shop or 4S store.
12
5
Share

What Does Fault Code 0751 Mean?

Fault code 0751 indicates an issue with Shift Solenoid A performance/stuck in the fully closed position. It is recommended to visit a 4S shop for transmission repair. Possible causes of this fault code include low transmission fluid level, dirty transmission fluid, mechanical failure of the shift solenoid, circuit issues, connector problems, or a malfunction in the Transmission Control Module (TCM). Below is detailed information about fault codes: 1. Modern cars are electronically controlled vehicles equipped with numerous electrical control components. When these components or their circuits malfunction, the computer stores the fault internally as a fault code. If the computer detects a fault code, it will illuminate the malfunction indicator lamp to alert the driver to inspect and repair the vehicle promptly. 2. Faults are categorized into intermittent faults and non-intermittent faults. Intermittent faults occur sporadically and may resolve on their own, while non-intermittent faults are persistent and require attention. Intermittent faults can be cleared using a diagnostic scanner. 3. For non-intermittent faults, use a diagnostic scanner to read the fault code and proceed with inspection and repair based on the code's indication. Solution: Connect the diagnostic scanner to the engine control unit, read the fault code, and perform the necessary checks and repairs as prompted. 4. Intermittent faults can be resolved by simply clearing the fault code, whereas non-intermittent faults require reading the fault code and conducting inspections and repairs based on the code's guidance.
2
0
Share

Does the Viloran have independent suspension?

The Viloran features independent suspension, with a MacPherson independent suspension at the front and a multi-link independent suspension at the rear. The Viloran is a mid-to-large-sized MPV under the Volkswagen brand, with dimensions of 5346mm in length, 1976mm in width, and 1781mm in height, and a wheelbase of 3180mm. The Viloran is equipped with two types of engines: a low-power version of the 2.0-liter turbocharged engine and a high-power version of the 2.0-liter turbocharged engine. The low-power version delivers a maximum power of 137kW and a maximum torque of 320Nm, while the high-power version offers a maximum power of 162kW and a maximum torque of 350Nm.
8
0
Share

Is the Corolla equipped with independent suspension?

The all-new Corolla adopts a front MacPherson independent suspension and a rear torsion beam non-independent suspension combination, which is the most widely used suspension setup in compact cars. The chassis is not covered with plastic guards but treated with a coating that is uniformly thick and covers a large area. Both front and rear wheel arches are wrapped with coating and plastic guards. The fuel lines have poor protection, being mostly exposed, but the exhaust pipe is surrounded by heat insulation tiles, which is quite considerate. Here are more details: 1. The front suspension of the new Corolla features a MacPherson independent suspension structure, an extremely common front suspension design for cars, offering advantages such as compact structure, lightweight, responsive handling, and good controllability. The front suspension lower control arm is made of forged steel, and the front suspension bearing seat is made of cast iron. The front suspension subframe of the new Corolla is an 'H'-shaped steel subframe; there is no engine underguard protection. The front suspension lower control arm is connected to the subframe via regular bushings; the front suspension lower control arm is connected to the bearing seat via rubber bushings. The benefit of not using bolt rigid connections is to reduce the impact force between components. 2. The rear suspension of the Corolla is a torsion beam semi-independent suspension, with both the torsion bar and spring base made of forged steel. The rear suspension torsion bar is connected to the body via regular bushings.
13
1
Share

How to turn on the air conditioning in the Roewe RX5?

Method to turn on the air conditioning in the Roewe RX5: Use the control switches on the air conditioning panel to activate the system. To turn on the cold air, press the AC switch, then rotate the temperature knob to the cold air mode. Next, adjust the fan speed knob to set the desired airflow for the cold air mode. The Roewe RX5 features Blue Core high-efficiency power technology, equipped with two turbocharged direct injection engines: a 2.0T and a 1.5T. The 2.0T engine delivers a maximum power of 220 horsepower and a peak torque of 350 Nm, while the 1.5T engine offers a maximum power of 169 horsepower and a peak torque of 250 Nm.
8
5
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.