What is the wading depth of the Elysion Hybrid?

1 Answers
ElliotLynn
07/24/25 11:27pm
The maximum wading depth of the Elysion Hybrid is 135mm. The wading depth of the Elysion Hybrid is determined by the height of the vehicle's chassis, which is the ground clearance listed in the model's parameter configuration. Generally, the greater the ground clearance, the higher the chassis, and the higher the safety factor when passing through waterlogged roads. Therefore, in terms of safe wading depth, the advantages of off-road vehicles and SUVs are obvious. However, for most compact and small cars with low chassis, the position of the vehicle's air intake should be used as a benchmark when passing through waterlogged roads. If the air intake of the Elysion Hybrid is below the water level during wading, water will be sucked into the engine's cylinders. Since water cannot be compressed like air, it can cause severe damage to the engine's mechanical components (such as connecting rods, pistons, crankshafts, etc.). Therefore, the wading depth must not exceed the height of the engine's air intake. The height of the engine's air intake, and thus the maximum wading depth, can also be increased by installing a snorkel. If wading is unavoidable, the following safe and correct procedures should be followed: Before wading, always turn off the auto start-stop function to prevent the engine from automatically restarting if the vehicle stalls in water, which could cause severe damage due to water ingress. Assess the underwater road conditions based on the passage of preceding vehicles and choose an appropriate entry point. Observe the path taken by other vehicles and follow it at a low speed, avoiding sudden acceleration or deceleration. On roads prone to water accumulation, use warning water level markers, trees, or the wheels and doors of other vehicles as reference points to estimate water depth before deciding whether to proceed. Be aware of your vehicle's safe wading depth. If the water depth exceeds half the height of the tires or the engine's air intake, do not proceed and choose an alternative route.
Was this review help?
19
0
Share
More Forum Discussions

Is the Elantra's body size small?

The length, width, and height dimensions of the Elantra are 4610mm/1800mm/1450mm, which are official data. The length of the Elantra refers to the distance between two vertical planes perpendicular to the vehicle's longitudinal symmetry plane and touching the outermost protruding parts at the front and rear of the car; the width refers to the distance between two planes parallel to the vehicle's longitudinal symmetry plane and touching the outermost rigid fixed protruding parts on both sides of the vehicle; the height refers to the distance between the highest point of the vehicle and the supporting plane of the vehicle. The naturally aspirated engine of the Elantra has a maximum power of 84.5kw and a maximum torque of 143.9 Nm. This engine reaches its maximum power at 6300 rpm and its maximum torque at 4500 rpm. It is equipped with multi-point electronic fuel injection technology and uses an aluminum alloy cylinder head and block. This engine is paired with a manual transmission (MT). The state has relevant regulations regarding vehicle dimensions. According to the national standard 'GB1589-89,' the total width of a vehicle does not include side mirrors. The limitation on vehicle width is to provide sufficient lateral clearance for overtaking between adjacent lanes. In other words, the significance of vehicle width data in the national standard is to ensure enough space during overtaking, preventing accidents due to excessive width or situations where road markings are narrower than the vehicle's width. Additionally, the national standard stipulates that the total width of a vehicle must not exceed 2.5m to meet the usage requirements of public roads.
11
1
Share

What brand is the Exeed LX?

Exeed LX is a brand under Chery. Here are the relevant details: 1. The Exeed LX is a compact SUV, equipped with a 1.6-liter turbocharged engine across the entire lineup. The engine has a maximum power of 145 kW, a maximum torque of 290 Nm, a maximum power speed of 5500 rpm, and a maximum torque speed ranging from 2000 to 4000 rpm. 2. The Exeed LX's engine features direct fuel injection technology and uses an aluminum alloy cylinder head and block. The engine is paired with a 7-speed dual-clutch transmission.
4
2
Share

Is the engine of Dongfeng Fengshen AX7 domestically produced or imported?

Dongfeng Fengshen AX7's engine is imported. Here are the relevant details: 1. Dongfeng Fengshen AX7 is a brand of the French PSA company. 2. Dongfeng Fengshen AX7 is equipped with 2.0L and 2.3L engines from the French PSA Group. In terms of performance parameters, the 2.0L engine has a maximum power of 108kW and a peak torque of 200Nm; the 2.3L engine has a maximum power of 126kW and a peak torque of 230Nm. The 2.0L model can be matched with a 5-speed manual transmission and Aisin's second-generation 6-speed automatic manual transmission, while the 2.3L model only offers a 6-speed automatic manual transmission. Dongfeng Fengshen AX7 is built based on Dongfeng's 'Dongfeng Military Industry Platform No. 2', utilizing Dongfeng's military resources to create a civilian SUV model. Whether in terms of exterior styling, body size, or power performance, it surpasses SUVs in the same class.
5
3
Share

How to Remove the Verna Universal Joint?

Verna universal joint removal and installation steps are as follows: 1. Remove the half-shaft lock nut. 2. Lift the vehicle on a hoist and raise it to an appropriate height. 3. Loosen the six fixing bolts of the inner CV joint. 4. Remove the control arm ball joint from the steering knuckle, then detach the half-shaft from the outer CV joint side, taking care not to damage the half-shaft dust boot during removal. 5. Disassemble the half-shaft and CV joint: Loosen the clamps on both sides of the CV joint dust boot, remove the dust boot and inspect it for damage or aging. Remove the snap ring: If the snap ring is installed on the outer side of the CV joint, use external snap ring pliers to expand and remove the outer CV joint. If the snap ring is installed on the inner side, use a hammer to strike the outer race of the CV joint to separate it from the half-shaft. 6. Disassemble the CV joint: Use a copper hammer to strike the inner race of the CV joint to make the CV joint and inner race perpendicular to the outer race, then remove the inner race, CV joint, and steel balls. 7. Reassemble in reverse order of disassembly to complete the replacement.
11
2
Share

What level does the CX-5 belong to?

The Mazda CX-5 is an urban off-road vehicle, classified as a compact SUV. Below is the relevant content introduction: 1. In terms of appearance, the facelifted new Mazda CX-5 continues the previous KODO design, still featuring a blackened honeycomb chrome grille paired with stylish daytime running lights. 2. For the interior, it largely retains the design style of the older model. The dashboard continues with the cannon-style design, the floating central control screen is small yet refined, and the polygonal air vents are symmetrically distributed. Compared to the trendy exterior design, the CX-5's interior design appears more conventional. 3. The CX-5 is equipped with two engines: one is a 2.0-liter naturally aspirated engine, and the other is a 2.5-liter naturally aspirated engine. The 2.0-liter naturally aspirated engine has a maximum power of 114 kW and a maximum torque of 200 N•m. The 2.5-liter naturally aspirated engine has a maximum power of 144 kW and a maximum torque of 252 N•m. Both engines are equipped with direct fuel injection technology and use aluminum alloy cylinder heads and blocks.
19
2
Share

How to Set the Cruise Control on Volkswagen Passat?

Passat cruise control usage is as follows: 1. Press the marked button to activate cruise control, and the corresponding indicator will appear on the instrument panel display. 2. When reaching the desired speed, press the set button at the end of the lever. Precautions for using cruise control: 1. Cruise control requires the driver to apply brakes, while adaptive cruise control enables automation. 2. When the driver presses the brake pedal, cruise control deactivates. The set speed value is retained and can be manually resumed. 3. Using cruise control may be hazardous on winding, steep, bumpy, slippery roads or in heavy traffic. Disable cruise and drive manually with caution. 4. When descending steep slopes, the vehicle may exceed the set speed. Always use brake assistance or deactivate cruise control completely.
3
4
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.