What is the wading depth of the Edge?

1 Answers
OIsabella
07/30/25 5:06am
The wading depth of the Edge is approximately 30cm. Below is an introduction to water-damaged vehicles: Definition of water-damaged vehicles: Water begins to accumulate in the vehicle, and internal components are damaged due to the water. Water-damaged vehicles are classified into different flood levels. Classification of flood levels for water-damaged vehicles: Flood level 1: Water just reaches the vehicle's chassis. Flood level 2: Water reaches halfway up the wheels. Flood level 3: Water almost completely submerges the tires. Flood level 4: Water reaches the engine hood. Flood level 5: Water completely submerges the engine hood. Flood level 6: Water submerges the roof.
Was this review help?
18
4
Share
More Forum Discussions

What are the symptoms of a bad rear shock absorber?

Damaged shock absorbers will leak oil. More relevant information is as follows: 1. In actual use, shock absorbers may produce noise. This is mainly due to collisions between the shock absorber and the leaf spring, frame, or bearings, damaged or detached rubber pads, deformation of the shock absorber dust cover, or insufficient fluid, among other reasons. This situation is relatively common. 2. After the car shock absorber is damaged, abnormal noises may also occur, specifically manifested as the shock absorber making noises when passing over bumpy roads. Additionally, uneven tire wear may occur, and the vehicle may experience unstable vibrations during driving, wheel tilting, and increased bump discomfort.
3
1
Share

Is a car tire temperature of 55 degrees normal?

A tire temperature of 55 degrees is relatively dangerous and requires attention. When the ambient temperature exceeds 30 degrees, the air pressure inside the tire can increase by 10% to 12%, making the tire more prone to bulging. Hazards of high tire temperature: When tire temperature is high, internal pressure increases, which can affect the vehicle's braking efficiency, the adhesion coefficient between the tire and the road surface, and the tire's rolling resistance. In severe cases, it may even lead to a tire blowout. Daily maintenance methods for car tires: Check the air pressure of all tires, including the spare tire, at least once a month when they are cold; do not exceed the reasonable speed limits required by driving conditions and legal regulations; regular wheel alignment and balancing are essential for ensuring driving safety and achieving optimal mileage; protect tires from sunlight, oil, acid, and hydrocarbon erosion. Daily tire usage precautions: Regularly check tire pressure. The standard tire pressure is approximately 2.2~2.6 bar. Excessive pressure can increase tire wear and may cause a blowout, while insufficient pressure can increase fuel consumption and make the ride bumpier. Generally, it is advisable to keep the pressure slightly lower, and slightly higher in winter.
10
2
Share

Audi A6 Starter Not Responding

Audi A6 starter not responding may be due to a car malfunction and requires timely inspection at a repair shop. Below are the reasons for the starter not responding: 1. The battery is dead or has weak power, causing the starter to fail to rotate or rotate slowly. 2. Loose or detached starter wiring, or a failed switch or solenoid switch, preventing the starter from responding. 3. Worn brushes or misaligned brush surfaces, weak springs causing poor commutator contact, resulting in the starter not functioning properly. 4. Short circuit or open circuit in the field coil or armature coil. 5. Dirty commutator or protruding mica sheets, causing poor contact between the brushes and the commutator, leading to the starter not working properly.
2
5
Share

What Brand of Car is Z?

There are two car brands with the letter Z as their logo, namely Opel and Zotye, one being domestic and the other foreign. Below are the brand introductions: Opel, known as Opel in Mainland China and Opel in Taiwan, is a German automobile company and a subsidiary of the American General Motors (GM), serving as GM's window in Europe. It was founded by Adam Opel and has a history of over a hundred years. In 1862, Adam Opel established the Opel company in Rüsselsheim, initially producing sewing machines and bicycles. The company began manufacturing cars in 1897. By 1924, Opel had built Germany's first automobile assembly line, significantly increasing production. In 1929, the company sold 80% of its shares to General Motors, making Opel a subsidiary of GM in Germany. Zotye Holding Group is a large private enterprise group focused on the research, development, and manufacturing of complete vehicles, engines, transmissions, and other key components. It currently has two major vehicle production bases in Zhejiang and Hunan, and two vehicle brands: Zotye Auto and Jiangnan Auto.
12
1
Share

Can I Replace Just One Car Shock Absorber?

It is not advisable to replace just one shock absorber; it's best to replace them in pairs on the same axle. If only one is replaced, the lifespan of the other will be shortened, and it may fail soon. More information about the car shock absorber system is as follows: 1. The shock absorber system consists of two parts: the shock absorber and the spring. Shock absorbers typically need to be replaced after about 100,000 kilometers. Even if the shock absorber is not broken or leaking oil, its damping effectiveness will be significantly reduced. 2. As long as the car is moving, the shock absorber is constantly working. Unlike other car parts, shock absorbers can last for a long time.
3
3
Share

What Causes Engine Oil Leaks?

Engine oil leaks can be caused by the following reasons: 1. Damaged or displaced sealing gaskets; 2. Improper installation of sealing components not following specified procedures; 3. Overfilling of lubricating oil or using incorrect oil type; 4. Prolonged engine use leading to aging and failure of sealing components; 5. Excessive pressure difference between engine interior and exterior. Solutions include: 1. Tightening various fastening nuts as required and according to specifications; 2. Timely replacement of failed sealing components; 3. Proper oil maintenance to prevent sludge buildup that may clog internal check valves or breather valves; 4. Ensuring proper sealing of external connecting pipes. Frequent disassembly may cause fastening rings to loosen/break or rubber parts to stretch, reducing sealing effectiveness and leading to oil seepage.
15
5
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.