What is the wading depth of the BYD Han?

1 Answers
OJesse
07/30/25 5:20am
The maximum wading depth of the BYD Han is 250mm. The wading depth of the BYD Han is determined by the height of the vehicle's chassis, which is the ground clearance listed in the model's parameter configuration table. Generally speaking, the greater the ground clearance, the higher the chassis, and the higher the safety factor when driving through waterlogged roads. Therefore, in terms of safe wading depth, the advantages of off-road vehicles and SUVs are obvious. However, for most compact and small cars with low chassis, the position of the vehicle's air intake should be used as a reference when passing through waterlogged roads. If the air intake of the BYD Han is below the water level during wading, water will be sucked into the engine's cylinders. Since water cannot be compressed like air, it will cause serious damage to the engine's mechanical components (such as connecting rods, pistons, crankshafts, etc.). Therefore, the wading depth must not exceed the height of the engine's air intake. The height of the engine's air intake, and thus the maximum wading depth, can also be increased by installing a snorkel. If wading is unavoidable, the following safe and correct operations should be performed: Before wading, be sure to turn off the auto start-stop function to prevent the vehicle from automatically restarting after stalling in the water, which could cause serious damage to the engine due to water ingress. Judge the underwater road conditions based on the passage of the vehicle ahead and choose a suitable entry point. Observe the path taken by other vehicles and follow their tracks at low speed, avoiding sudden acceleration or deceleration. On roads prone to water accumulation, observe warning water level markers, trees, and reference points such as the wheels and doors of other vehicles to judge the water depth before deciding whether to proceed. Know your vehicle's safe wading depth. If the water depth exceeds half the height of the tires or the engine's air intake, do not proceed recklessly; choose an alternative route instead.
Was this review help?
4
0
Share
More Forum Discussions

Is the Engine Ticking Sound Indicative of Cylinder Scoring?

Engine ticking is not necessarily indicative of cylinder scoring. The causes of engine ticking can include aging or loosening of engine mounts, excessively rich air-fuel mixture, or malfunction of the high-pressure fuel pump. For engines with high mileage, excessive clearance between the camshaft and hydraulic lifters can also produce such sounds. An engine is a machine capable of converting other forms of energy into mechanical energy. It can refer to either a power generation device or the entire machine including the power unit. Types of engines include internal combustion engines, external combustion engines, gas turbines, and electric motors. The basic structure of an automotive engine consists of components such as the water pump housing, connecting flange or pulley, water pump shaft and bearings or integrated bearing units, water pump impeller, and sealing devices, making it a fundamental part of the automobile.
20
3
Share

What to Do When the Car Turn Signal Suddenly Flashes Faster?

The solution to the sudden increase in the flashing speed of the car turn signal is: it may be due to a malfunction in the vehicle's turn signal flasher, and replacing the flasher should resolve the issue. The turn signal is an important indicator light that is activated when a motor vehicle turns to alert surrounding vehicles and pedestrians. The turn signal bulb uses a xenon tube, controlled by a microcontroller circuit, with left and right alternating flashes working continuously. The turn signal employs a flasher to achieve the blinking effect, which can be mainly categorized into three types: resistance wire type, capacitor type, and electronic type. Precautions for using turn signals include: 1. Activate the turn signal in advance when making a turn; 2. Use the left turn signal when overtaking and the right turn signal when returning to the original lane; 3. When activating the turn signal, pay attention to observing pedestrians and passing vehicles before performing any vehicle maneuvers.
14
1
Share

What is the use of the Lexus hold button?

The function of the Lexus hold button is: After using this function, it allows the car's transmission to operate the automatic transmission like a manual transmission. After pressing the button, the car enters the hold mode, and the hold mode indicator light will illuminate. Pressing the button again will turn off the indicator light, and the car will return to the normal driving mode. Taking the Lexus ES 2020 300h Excellence Edition as an example, it belongs to the mid-to-large car category, with body dimensions of: length 4975mm, width 1866mm, height 1447mm, a wheelbase of 2870mm, a fuel tank capacity of 49.3 liters, and a curb weight of 1720kg.
20
3
Share

Does the Tiguan L380 Have a Particulate Filter?

The Tiguan L380 is equipped with a particulate filter. A particulate filter is a ceramic filter installed in the diesel engine's emission system, which captures particulate emissions before they enter the atmosphere. Functions of the Particulate Filter: The particulate filter can reduce the soot produced by the diesel engine by more than 90%. The captured particulate emissions are subsequently burned off during vehicle operation. To check whether a vehicle has a particulate filter, you can use the following three methods: 1. Refer to the and to see if there is a particulate filter function. Additionally, carefully check the fault codes in the manual to see if there is a "Particulate Filter" warning light indicator. 2. Check the label on the oil filler cap. If the oil cap clearly states 0W-20 grade oil, it indicates the presence of a particulate filter. 3. Look behind the three-way catalytic converter on the exhaust pipe for a cylindrical section. If present, that is the particulate filter.
1
3
Share

Do You Need to Wait for a Red Light When Making a U-Turn?

If the U-turn signal light is red, you must wait to make a U-turn; otherwise, it will be considered running a red light. According to the "Road Traffic Safety Law," this violation incurs a penalty of 6 demerit points and a fine of 200 RMB. If there is no dedicated U-turn signal light, and the gap is marked with a dashed line, the U-turn is not affected by the traffic light and does not require crossing the pedestrian crossing. However, if the gap is marked with a solid line, the U-turn must cross the pedestrian crossing and is subject to the left-turn signal light. Making a U-turn directly without following these rules may result in being photographed or penalized by on-site traffic police. When making a U-turn that requires crossing a pedestrian crossing, yielding to pedestrians is mandatory: 1. If pedestrians are walking on the right side of the crosswalk and have not reached the centerline of the road, vehicles on the left side must slow down and allow them to pass safely. 2. If pedestrians are waiting outside the boundary of the motorized and non-motorized lanes and have not entered the roadway, vehicles should slow down and let them pass safely. 3. If pedestrians have crossed the boundary between motorized and non-motorized lanes, failing to stop for them is a violation and punishable. 4. If pedestrians enter the motorized lane (Lane A) from the crosswalk, vehicles in Lane B must slow down and allow them to pass safely. Failing to stop for pedestrians in Lane A is a violation and punishable. 5. If pedestrians are waiting at the centerline of the road but have not entered the motorized lane, failing to stop for them is a violation and punishable. 6. If pedestrians cross the centerline and enter the motorized lane, failing to stop for them is a violation and punishable. 7. If the road is divided by a median with greenery, and pedestrians are waiting in the central stopping area, vehicles must slow down and allow them to pass safely. Permissible U-turn scenarios: 1. If an intersection has a U-turn sign, a U-turn is allowed. If there is a U-turn signal light, follow its instructions. If no signal light exists, make the U-turn without obstructing other vehicles or pedestrians. 2. If there is no explicit "No U-Turn" or "No Left Turn" sign at an intersection, a U-turn is allowed. The absence of such signs, along with no solid centerline, means you can proceed with the U-turn. 3. U-turns are also permitted in yellow grid zones. These zones are no-parking areas marked at intersections prone to congestion or near important facilities. While stopping in these zones is prohibited, making a U-turn is allowed unless a median barrier is present. 4. If a U-turn signal light is present, follow its instructions—only proceed on green. 5. If a "No Left Turn" sign coexists with a "U-Turn Permitted" sign, U-turns are allowed, but left turns are not. Note that "No U-Turn" and "No Left Turn" are not the same. Key considerations when making a U-turn: 1. Observe road markings—if a solid line is present, U-turns are prohibited under any circumstances. Continue driving to find a suitable location. 2. If a "No Left Turn" sign is posted, U-turns are also prohibited at that intersection, as U-turns inherently involve a left-turn maneuver. 3. U-turns must be made from the innermost left-turn lane. If you are in the second left-turn lane, a U-turn is not permitted. 4. Always yield to oncoming traffic when making a U-turn. Failing to do so may result in bearing full liability for any accidents. 5. Near intersection stop lines, lane arrows guide vehicle positioning. Not all leftmost lanes are for left turns—some may have straight arrows. Even if no explicit "No U-Turn" signs are present, U-turns are prohibited in such lanes.
18
2
Share

How to Remove Anti-Theft License Plate Screw Caps?

The method to remove anti-theft license plate screw caps is: Use a flathead screwdriver and a hammer. Insert the screwdriver into the seam and strike the head of the screwdriver with the hammer to remove it. License plate screw caps serve an anti-theft sealing function. The screws on license plates have anti-theft measures; if you want to remove the license plate, you can only destroy the anti-theft device. The first Chinese character on a vehicle license plate represents the abbreviation of the province or municipality directly under the central government. The uppercase letter following the Chinese character indicates the city or district. License plates are hard-coded number plates issued by vehicle management authorities after reviewing, inspecting, and registering vehicles that have applied for license plates. Vehicle license plates are the legal certificates permitting cars to drive on the road.
7
2
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.