What is the voltage of the battery in the Bora?

1 Answers
BrynleeMarie
07/29/25 10:30pm
Volkswagen Bora series batteries are 12V, while buses and trucks use 24V batteries. The car battery should avoid being parked in an open parking lot for a long time. If parking for an extended period, remove the battery and take it with you to prevent freezing and damage. In winter, the engine is harder to start. Each engine start attempt should not exceed 5 seconds, and the interval between restarts should be no less than 15 seconds. If the engine fails to start after multiple ignition attempts, check for specific reasons in other areas such as the circuit, ignition coil, or fuel system. Avoid repeatedly starting the engine without interruption, as this can cause the battery to burn out due to excessive discharge. Car batteries should be charged frequently. If left unused for a long time, the battery will gradually self-discharge until it becomes unusable. Therefore, start the car periodically to charge the battery. However, the car battery is connected to the alternator in the entire circuit. As soon as the car starts, the alternator can charge the battery. Therefore, in most cases, the battery operates in a fully charged state. This operating state is called float charging, where the power source and battery are connected in parallel in the circuit, with the power source providing a small current to compensate for the battery's loss, keeping it in a fully charged state.
Was this review help?
10
2
Share
More Forum Discussions

How to Replace the Brake Light Bulb on a Langdong?

Method for replacing the rear brake light on a Langdong: Remove the upper trim panel in the trunk, pinch the clips on both sides to release them, then pull out the old bulb and insert the new one. Below is some related information: 1. Brake Light: The brake light is primarily red in color to enhance light penetration, making it easier for vehicles behind to notice when the front vehicle brakes, even in low visibility conditions, thereby helping to prevent rear-end collisions. 2. Installation Location: The brake light is part of the car's taillights and is usually integrated with other car lights. There are two common installation positions: (1) Brake lights installed at both ends of the rear of the car, which are a type of taillight. (2) High-mounted brake lights, installed on the upper part of the rear of the car.
10
0
Share

What is the reason why the reversing camera of Mercedes-Benz suddenly stops working?

The reason why the reversing camera of Mercedes-Benz suddenly stops working is that the host system is stuck. In this case, the vehicle needs to be restarted. If the problem persists after restarting the vehicle, it is necessary to go to a repair shop or a 4S store for professional inspection and repair. Most of the cars on the market are equipped with a reversing camera function. Although the reversing camera can facilitate people's driving, it also has a certain failure rate. The body size of the new Mercedes-Benz C-Class is 4786mm in length, 1810mm in width, and 1457mm in height, with a wheelbase of 2920mm. In terms of interior, it is equipped with a 10.25-inch central control LCD screen and a new-style three-spoke multifunctional steering wheel. In terms of power, it is equipped with a 1.6T engine, a 1.5T engine, and a 2.0T engine.
9
3
Share

What is the issue with abnormal post-processing wiring harness?

The main causes of abnormal post-processing wiring harness include the following aspects: 1. Natural factors: The wiring harness has exceeded its service life, leading to aging of the wires, damage to the insulation layer, and inadequate mechanical strength, resulting in short circuits, open circuits, and grounding between circuits, which can burn out the wiring harness. Many cases of electrical equipment malfunction are caused by poor contact, often due to oxidation or deformation at the wiring harness terminals. 2. Equipment failure causing damage to the wiring harness: Malfunctions in electrical equipment can easily damage the wiring harness, with common issues including short circuits and open circuits. 3. Subjective human factors: During the assembly or repair of automotive components, metal objects may crush the wiring harness, causing the insulation layer to rupture; improper positioning of the wiring harness; incorrect connection of electrical equipment leads; reversed connection of the battery's positive and negative leads; and during the repair of problematic circuits, haphazard wiring connections or cutting of wires can affect electrical equipment and even burn out the wiring harness.
17
5
Share

What is the function of the fuel pump return valve?

The function of the fuel pump return valve is to automatically maintain the fuel pressure in the entire oil pressure system at a certain value, ensuring that the difference between the oil pressure in the fuel supply pipe and the intake manifold pressure remains constant (generally 250-300 kPa). Below is a detailed introduction to the fuel pump return valve: 1. Concept: The fuel pressure regulator, also known as the return valve, is the part of the fuel system responsible for regulating internal fuel pressure, controlled by the system oil pressure and intake manifold pressure (negative pressure). 2. Importance: If the fuel pressure regulator malfunctions, it will directly affect the accuracy of fuel injection. Low fuel pressure can cause low idle speed in the vehicle, a feeling of insufficient fuel supply at high speeds, and in severe cases, difficulty starting or even failure to start. In summer, it may lead to insufficient power for operating the air conditioning. High fuel pressure, on the other hand, can result in high idle speed and overly sensitive accelerator pedal response.
10
0
Share

Is the jl476zqcf engine a Blue Whale?

The Changan jl476zqcf model engine is a Blue Whale engine. More information about the Blue Whale engine is as follows: 1. The Blue Whale engine is independently developed by Changan and belongs to domestic technology. The maximum power of the Blue Whale engine is 233 horsepower (171 kilowatts), and the maximum torque is 360 Newton-meters. 2. In addition to its strong power, the Blue Whale engine also demonstrates low fuel consumption and was one of China's Top 10 Engines in 2017. Established in 2006, "China's Annual Top 10 Engines," "Ward's Annual 10 Best Engines," and "International Engine of the Year" are ranked as the world's top three engine awards.
16
3
Share

How to turn on the heating in BYD S6?

Method to turn on the heating in BYD S6: Rotate the temperature control knob to the red zone, then turn on the fan speed switch. Note that the AC button does not need to be pressed for heating. The car's heating system plays a significant role, especially in winter when it becomes crucial. The heating system not only increases the interior temperature but also helps defog the windows. There are techniques for using the heating system in winter. Particularly when the car is cold-started, the engine temperature is very low. Suddenly turning on the heater will increase engine load, lead to higher fuel consumption, and prolong the time for the coolant temperature to rise. Starting the AC without any preheating will reduce engine efficiency and cause significant damage to the engine itself. The BYD S6 is positioned as a mid-to-high-end domestic SUV, with body dimensions of 4810mm in length, 1855mm in width, and 1680mm in height, a wheelbase of 2720mm, and front-engine, front-wheel-drive configuration.
11
1
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.