What is the tutorial for replacing the low beam headlight of Baojun 730?

[MacMiguel]

The steps for replacing the low beam headlight of Baojun 730 are: 1. Open the engine hood; 2. Open the headlight cover; 3. Park the car on a flat surface; 4. Secure the car and turn the light switch to the 0 position; 5. Move the turn signal lever to the middle position, and wait for a while after turning off the headlights to allow the bulb to fully cool; 6. When replacing the bulb, be sure to follow the instructions, and the replacement bulb model must match the car's bulb model. The bulb specifications are usually marked on the bulb glass or the bulb base. Be careful not to touch the bulb glass with your fingers during the operation. Baojun 730 is a car product under SAIC-GM-Wuling Baojun. The car's body dimensions are 4780mm, 1820mm, and 1755mm, with a maximum cargo space of 1680L, a top speed of 150 km/h, a fuel tank capacity of 52 liters, and a weight of 1420kg.

[SabrinaLynn]

I'm quite familiar with changing low beam headlights! The Baojun 730 uses H7 halogen bulbs, and it's no problem to replace them yourself. Just prepare new bulbs, a long-handled screwdriver, and gloves. First, open the hood, and there's a round cover at the back of the headlight assembly—unscrew it counterclockwise. Note that the wire connector has clips; press both sides to remove it. For the old bulb's base retainer, use the screwdriver to press the spring clip and then push it open. When installing the new bulb, be sure to wear gloves and avoid touching the glass. Align it with the slot, place it properly, and then fasten the clip securely. After reconnecting the plug, test the light first to see if it works before putting the cover back on. Pay special attention to the angle and avoid forcing any parts. The whole process takes just over ten minutes, with careful operation being the key.

[SanAnastasia]

Last time I replaced the bulbs on my 730 myself, here's my experience: First, buy H7 halogen bulbs, around 40 yuan online. Before starting, turn off the light switch and open the hood to locate the rear of the headlight. The black plastic cover can be removed by turning it counterclockwise 90 degrees. Then you'll see the wire connected to the bulb; carefully unplug it by pressing the clips on both sides of the connector. The bulb is held by a metal clip; press the spring clip with your thumb and push it sideways to remove the bulb. When installing the new bulb, make sure the three tabs on the base align with the notches in the socket. After installation, secure the clip firmly. Don't forget to test the lights after reassembly to avoid rework. I saved 200 yuan in labor costs by doing it myself—definitely worth a try.

[DiCamila]

As a mechanic with ten years of experience, here are some key reminders: The low beam bulb model for the Baojun 730 must be H7. Always wear gloves during the operation, as skin oils can cause the bulb to burn out prematurely. When removing or installing, be careful not to lose the dust-proof rubber ring on the back cover, otherwise, moisture may enter during rainy days. Before installing the bulb, take a photo of the base position with your phone to avoid incorrect installation. If the light does not focus during testing, it is likely that the bulb is not properly seated. To switch to LED, an additional decoder is required; modifying the original lamp socket directly may trigger fault codes. It is recommended to retain the original halogen bulbs for their affordability and reliability.

[MilesRose]

Money-Saving Tips for Baojun 730 Owners! Replacing Bulbs in Just Three Steps: Purchase the same model H7 halogen bulb - only 25 RMB with free shipping on Taobao. Open the engine hood and locate the black rotating cap at the rear of the headlight, then unscrew it to the left. When unplugging the connector, press the metal tabs on both sides of the interface—avoid pulling forcefully. Gently press the bulb's retaining clip to release it before replacement. Use your phone's flashlight for better visibility throughout the process. After installation, always test the high and low beams before closing the cover. If upgrading to LED, note: the original dust cover may not fit, so buy a dedicated extended cover; low-quality LEDs may flicker, so opt for reputable brands with cooling fans. This method saves you 300 RMB compared to visiting a 4S shop!