What is the trunk size of the Volkswagen Sharan?

2 Answers
AlanaAnn
08/27/25 2:12am
The trunk capacity of the Volkswagen Sharan can be flexibly adjusted between 375 liters, 711 liters, 1167 liters, and 2297 liters. With all seats upright, the trunk capacity is 375 liters. When the seats are folded down, the maximum trunk capacity can reach up to 2297 liters. Below is an introduction to the hidden design features of the trunk. Escape Switch: This device is located at the lock cylinder of the trunk latch. On the trunk lid, you will find a small cover in black or another color. Inside the cover, there is a white pull tab, pull cord, or crescent-shaped switch. Although the forms vary, the principle is the same. By pulling this tab forcefully, the trunk can be opened, allowing access from inside the vehicle when needed. Small Hooks: Hooks can be found in the trunks of most vehicles, though their positions and forms may differ. Some lower-trim models may not come with hooks but have pre-installed slots for adding hooks later, making it convenient to hang items. First Aid Kit: Many vehicle models come equipped with an in-car first aid kit from the factory, containing commonly used emergency tools such as gauze, scissors, and adhesive tape. Some models' first aid kits also include instructions for proper usage in emergencies. Luggage Compartment Partition: Most hatchbacks, SUVs, and some MPV models have a partition in the trunk area, which is a factory-installed accessory. The vehicle is designed with a reserved installation spot for this partition. It not only enhances the privacy and security of the luggage but also clearly separates the trunk from the passenger compartment. It is advisable not to place items on top of the partition, as they may obstruct the driver's rearview and could potentially be thrown into the passenger compartment during braking, posing a risk to occupants.
Was this review help?
9
4
Share
ONathan
09/08/25 8:56am
The trunk capacity of the Sharan is approximately 710 liters in standard configuration, which is quite spacious and can accommodate several large suitcases or camping gear. When the rear seats are folded down, it can expand to around 2297 liters, offering an astonishing amount of space—I've even managed to fit an entire sofa in there. With a height of about 90 cm and a width of 1.1 meters, it's suitable for transporting tall items. The large opening makes loading and unloading convenient, and the low threshold is great for moving heavy items. It's a bit more practical than the Toyota Sienna, but be careful not to overload it to avoid instability. This MPV is reliable for both daily use and travel.
Was this review help?
14
4
Share
Expand All
More Forum Discussions

What is traffic violation code 1039B?

Violation code 1039B means: Driving a non-motor vehicle in violation of traffic control, restricted passage, or prohibited passage regulations. According to the relevant provisions of the "Road Traffic Safety Law of the People's Republic of China", the penalty includes: Demerit points (deduction): 0 points; Fine amount: 50 yuan; Other penalties: None. Traffic violation codes consist of four to five digits, classified according to the principles of the traffic law. The sequence from left to right is: the first digit represents the behavior classification code, the second digit represents the demerit point classification code, the third and fourth digits are sequential numbers, and the fifth digit indicates the specific item number. First digit: Behavior classification code, indicating the category in the Road Traffic Law; Second digit: Demerit point classification code, indicating the category of demerit points for the traffic violation; Third, fourth, and fifth digits: Sequential code, indicating the order of the violation within the same behavior category. For example: 13035—"1" indicates a motor vehicle violation, the second digit "3" indicates 3 demerit points, and "035" indicates the fifth item of the third violation in the 3-point deduction category. Behavior classification code violation descriptions: Codes starting with "1" indicate motor vehicle violations, e.g., 1003. Codes starting with "2" indicate non-motor vehicle violations, e.g., 2002. Codes starting with "3" indicate pedestrian or passenger violations, e.g., 3030. Codes starting with "4" indicate highway violations, e.g., 4002. Codes starting with "5" indicate other regulations, e.g., 5005. Codes starting with "7" indicate provincial, autonomous region, or municipal implementation rules, e.g., 7008. Codes starting with "8" indicate local regulations of cities (prefectures, autonomous prefectures, or leagues), e.g., 8606. There are four common methods to check motor vehicle violations: Visit the office halls of traffic branches in various districts and counties to query through touch terminals; Log in to the external service website of the local Public Security Bureau's Traffic Management Bureau, find the vehicle violation query section, enter the license plate number and engine number, and click to query; Call the hotline (area code + 114) to query: Follow the operator's instructions to enter the license plate number and engine number for query. The operator will announce the results via voice, which is a quick query method. Use the Traffic Management 12123 app (V2.8.1B437 for iOS 15+ or V2.8.1B274 for Android 12+) to query. For example, on an Android device: Open the Traffic Management 12123 app on an Android phone, log in, and view recent violation records on the homepage.
6
5
Share

What Causes the Engine Warning Light with an Exclamation Mark?

There are 7 main reasons why the engine warning light may illuminate: Sensor Malfunction: This includes sensors such as coolant temperature, crankshaft position, air flow, intake air temperature, and oxygen sensors. When these sensors are damaged, have poor connections, or their signals are interrupted, the vehicle's ECU cannot accurately obtain engine data, which triggers the engine warning light. Fuel or Oil Quality Issues: If fuel or engine oil is not added according to the manufacturer's specifications, it may cause engine wear and trigger the warning light. Poor Combustion of Air-Fuel Mixture: Poor combustion can lead to engine carbon buildup or knocking. When detected by the oxygen sensor and reported to the ECU, the warning light will illuminate as a warning. Issues such as faulty spark plugs, ignition coils, fuel pumps, or clogged fuel lines can cause poor combustion. Turbocharger Problems: Issues with the intake boost piping or turbocharger can also trigger the engine warning light. The most common problem is turbocharger damage, which may also be accompanied by symptoms such as oil leaks, excessive oil consumption, reduced power, metallic noises, or blue/black smoke from the exhaust. Intake Problems: If the vehicle's intake system malfunctions, it may lead to blocked engine pipes, and in severe cases, trigger the engine warning light. A dirty air filter that is not cleaned regularly can cause intake issues. Exhaust Problems: Exhaust system faults can also cause the engine warning light to illuminate. Common causes include faulty rear oxygen sensors, catalytic converters, exhaust camshafts, or bearings, with the catalytic converter being the most frequent issue. Using leaded gasoline, lead- or silicon-containing lubricant additives, physical damage to the catalytic converter, or fuel system malfunctions can all lead to catalytic converter failure. Anti-Theft System Malfunction: If the vehicle's electronic anti-theft system fails or if the anti-theft controller does not match the engine's electronic controller, the anti-theft system may prevent the engine from operating normally and trigger the warning light. If the engine warning light illuminates, follow these steps: First, check whether the engine is running normally. If there are issues such as shaking or smoke, avoid restarting the engine. Note: Do not restart the engine if the red warning light is on. If the engine can be started, turn it off and wait 5-10 minutes. Without pressing the brake pedal, press the start button once or turn the key halfway to the "ON" position (without pressing the clutch). The vehicle will perform a self-check after powering on. Observe whether the warning light turns off after 5-10 seconds. If the warning light remains on, visit a service center as soon as possible. Technicians can use a portable diagnostic tool to read the trouble codes, identify the issue, and perform targeted repairs.
16
4
Share

What is the difference between 15w40 and 10w40?

The main difference between 15w40 and 10w40 engine oils lies in their low-temperature fluidity. Engine oil primarily serves the following functions: 1. It effectively protects internal engine components, reducing wear and preventing aging. 2. Inside the engine, it minimizes mechanical friction resistance, ensuring smoother operation. 3. It helps lower the internal temperature of the engine, aids in heat dissipation, prevents rust and aging of internal parts, and extends the engine's service life.
2
0
Share

What is BFGOOD tire?

BFGOOD is the BFGoodrich tire brand under Michelin, known for its strong traction, excellent grip, flexible steering control, and stylish tread design. Car tires are one of the important components of a vehicle, directly contacting the road surface and working together with the car suspension to mitigate shocks during driving. The functions of car tires include: ensuring good ride comfort and smooth driving; maintaining excellent adhesion between the wheels and the road; improving the vehicle's traction, braking, and off-road capability; and bearing the weight of the car. The critical role tires play in automobiles has gained increasing attention.
1
0
Share

How to reset the tire pressure light on an Audi Q3?

Here are the steps to reset the tire pressure on an Audi Q3: 1. First, power on the car and press the CAR button on the MMI system; 2. Press the return button, then use the knob to select the Tire Pressure Monitoring System; 3. Next, press 'Store Tire Pressure' and select 'Store Now' to complete the process. Additional information: Most cars are equipped with a tire pressure monitoring system, which typically uses wheel speed sensors to monitor the rotation speed of the wheels. Tires are the only part of the car that comes into contact with the ground, making tire pressure critically important for tire performance.
1
2
Share

What does HOLD mean on the automatic gear lever of the Sylphy?

HOLD on the automatic gear lever of the Sylphy refers to the gear hold function. More details about HOLD are as follows: 1. HOLD means "hold." When this button is pressed, the automatic transmission enters "hold mode," and the "hold mode indicator light" on the dashboard illuminates. Pressing the HOLD button again returns the transmission to the normal automatic shifting mode, and the "hold mode indicator light" on the dashboard turns off. 2. In hold mode, the transmission remains in a specific gear, making the automatic transmission operate similarly to a manual transmission.
16
5
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.