What is the trunk capacity of the Civic?

How to Check All Your Driver's License Test Scores?

Driver's license test scores are usually available immediately after the exam. If you forget your scores and want to check all of them, you can visit the traffic management website for inquiries. Related information: 1. Introduction: The content and passing standards of the test subjects are unified nationwide. The test sequence follows Subject 1, Subject 2, Subject 3, and Subject 4, which are theoretical knowledge, field driving skills, road driving skills, and civilized driving knowledge, respectively. You can only proceed to the next subject after passing the previous one. 2. Additional Information: The driver's license test, also known as the driving test, is conducted to obtain a motor vehicle driver's license. The content and passing standards of the test subjects are unified nationwide. The basic process of the driver's license test includes form filling, physical examination, application acceptance, fee payment, examination, and certificate issuance.

6

1

Share

How to Reset Tire Pressure on the Tiguan?

Tiguan's tire pressure reset methods are: 1. Press and hold the tire pressure reset button in front of the gear shift for five seconds to reset; 2. Select tire pressure through the multifunction steering wheel on the instrument panel and then store it. The Tiguan is a compact SUV produced by Shanghai Volkswagen, with a body length, width, and height of 4506mm, 1809mm, and 1685mm respectively, and a wheelbase of 2684mm. The Tiguan is equipped with Volkswagen's mainstream 1.8TSI and 2.0TSI engines, which deliver excellent performance in both power and fuel economy, matched with a 6-speed manual transmission or an Aisin 6-speed automatic transmission.

10

5

Share

How to Check Engine Oil Pressure?

Engine oil pressure should be measured and checked using a dedicated oil pressure gauge. The measurement method is as follows: 1. Disconnect the wiring harness plug of the oil pressure sensor and remove the oil pressure sensor; 2. Screw the hose connector of the oil pressure gauge into the threaded hole where the oil pressure sensor is installed and tighten the connector; 3. Place the oil pressure gauge in a location where it will not come into contact with rotating or high-temperature engine components; 4. Start the engine and check for oil leaks at the oil pressure gauge connector. If there is any leakage, turn off the engine and retighten the connector; 5. Run the engine until it reaches normal operating temperature, then check the oil pressure gauge readings at both idle and 2000 rpm, comparing them with the standard pressure values.

6

3

Share

What does the 'a' on the electronic handbrake mean?

The 'a' on the electronic handbrake represents the vehicle's auto-hold function. Vehicles equipped with electronic handbrakes typically come with this feature, which is not enabled by default and requires manual activation by the driver. Once the auto-hold function is activated, it eliminates the need for frequent operation of the handbrake or electronic handbrake. For automatic transmission models, it also reduces the need for frequent shifting between D to N or D to P. When the vehicle comes to a complete stop during driving, even if the brake pedal is released, the vehicle will not move forward automatically. It will only resume driving when the accelerator pedal is pressed again.

4

2

Share

What Causes Shaking When Braking in D Gear?

If the shaking when braking in D gear is slight, it is a normal phenomenon. However, if the shaking is severe, it may be caused by damage to the engine mounts. The engine mounts, usually made of rubber, are located where the engine connects to the frame and serve to cushion the engine's vibrations. D gear, also known as the drive gear, engages the corresponding forward gear hydraulic circuit automatically based on throttle opening and vehicle speed signals when the gear selector is in this position. Automatic transmission cars use an automatic transmission to adjust speed, where the transmission's control system automatically selects the appropriate gear based on engine speed and load, replacing the driver's subjective judgment and manual gear shifting.

17

5

Share

What does the oil grade 10w40 mean?

The oil grade 10w40 refers to the viscosity of the oil being 10w40. The number before the 'w' represents the cold start performance, with smaller numbers indicating easier engine starting in cold weather. Common grades include 0W, 5W, 10W, and 15W. The '40' indicates the oil's viscosity characteristics at high temperatures. High-viscosity oils (with higher values) may be more suitable for high-speed driving or heavily loaded vehicles. Engine oil, also known as motor lubricant, serves functions such as lubrication and wear reduction, auxiliary cooling, rust and corrosion prevention, and shock absorption. Engine oil consists of base oil and additives. The base oil is the main component of the lubricant, determining its fundamental properties, while additives compensate for and improve any shortcomings in the base oil's performance.

9

2

Share

What is the trunk capacity of the Civic?

How to Check All Your Driver's License Test Scores?

How to Reset Tire Pressure on the Tiguan?

How to Check Engine Oil Pressure?

What does the 'a' on the electronic handbrake mean?

What Causes Shaking When Braking in D Gear?

What does the oil grade 10w40 mean?

Is It Advisable to Purchase a New Energy Vehicle That Has Been in Inventory for Two Years?

How Many Points Are Deducted for Carrying Passengers on a Light Motorcycle?

What to Do When the Car Body Shakes Severely with AC On?

How long can a National V emission standard car still be driven?