What is the trunk capacity of the BYD Han?

1 Answers
Joseph
07/30/25 3:39am
The trunk depth of the BYD Han is 1000mm, the width ranges from 920mm to 1260mm, and the height is 470mm. Below is relevant information about the BYD Han: 1. Exterior: Dimensions are 4980×1910×1495mm with a wheelbase of 2920mm. The front face features a closed design approach, presenting a clean and elegant appearance. The design elements transform the dragon mouth into a flat design, complemented by horizontal lines for enhanced aesthetics. 2. Powertrain: The BYD Han is equipped with BYD's self-developed lithium iron phosphate blade battery, offering two range versions: the Super Long Range version and the Four-Wheel Drive High-Performance version. The Super Long Range version is powered by a permanent magnet synchronous single motor delivering a maximum power of 163kW and a maximum torque of 330N·m, with a maximum range of 605km.
Was this review help?
4
2
Share
More Forum Discussions

What is the difference between 0W20 and 0W40 engine oil?

OW20 and OW40 are viscosity grades of engine oil, where higher numbers indicate higher viscosity. The specific differences are as follows: 1. The base viscosity of 0W20 and 0W40 engine oils differs. 0W40 engine oil has a higher viscosity than 0W20, meaning that at the same temperature, 0W40 flows much less easily than 0W20. 2. The high-temperature shear resistance of OW20 and OW40 engine oils varies. 0W40 engine oil has higher shear resistance than 0W20, providing a stronger and thicker oil film. 0W-40 offers better high-temperature protection due to its higher kinematic viscosity.
2
3
Share

How to Adjust the Rearview Mirror of the Buick Excelle?

Rearview mirrors should not be adjusted randomly. Here are the specific steps to adjust the rearview mirrors of the Buick Excelle: 1. Enter the car and check if the rearview mirror angle is appropriate. 2. Locate the rearview mirror adjustment switch on the left side of the central air conditioning panel. 3. Turn the knob to the middle "0" position to deactivate the mirror adjustment function. 4. Rotate the knob to the "R" position to select the right rearview mirror for adjustment. 5. Rotate the knob to the "L" position to select the left rearview mirror for adjustment. 6. Press the knob in different directions to adjust the mirror's orientation accordingly.
7
5
Share

What Causes the Brake Warning Light to Illuminate?

The brake warning light illuminates due to insufficient brake fluid, a malfunctioning or unreset brake switch, or severely worn brake pads. Insufficient Brake Fluid: Brake fluid is an essential component of the vehicle's braking system. When the driver presses the brake pedal, the force is transmitted via the master cylinder piston through the brake fluid to the wheel cylinders at each wheel, causing the brake pads to engage the wheels and stop the vehicle. If the brake fluid is low, it must be replenished promptly. Check for a Malfunctioning or Unreset Brake Switch: Inspect the brake wiring for poor contact or short circuits. Examine the brake pedal pad for integrity, check if the brake rubber ring is severely worn, and determine whether the brake switch is damaged. Address any identified issues immediately. Severely Worn Brake Pads: The warning light may stay on if the brake pads are excessively worn. Replacing the brake pads will resolve this issue.
19
5
Share

How often should the spark plugs be replaced on a Golf 7?

The spark plugs on a Golf 7 should be replaced every 30,000 to 50,000 kilometers, with the exact interval varying depending on the material of the spark plugs. Under normal maintenance conditions, they should be replaced between 40,000 and 60,000 kilometers. However, this may differ based on the brand and engine type, so it's recommended to follow the owner's manual. Here are some general guidelines for replacement: platinum spark plugs should be replaced at 40,000 kilometers, standard nickel alloy spark plugs at 20,000 kilometers, and iridium spark plugs at 60,000 to 80,000 kilometers. Steps for replacing spark plugs: Open the hood, lift the plastic engine cover, and remove the high-voltage ignition wires. Mark each wire according to its corresponding cylinder position to avoid confusion. Use a spark plug socket to remove each spark plug one by one. While removing them, check for any debris like leaves or dust around the area and clean it thoroughly. Insert the new spark plug into the spark plug hole, hand-tighten it a few turns, and then use the socket to tighten it further. Reinstall the high-voltage ignition wires in the correct firing order, reattach the engine cover, and finally start the vehicle to check if the spark plugs are functioning properly.
2
4
Share

Where is the rear wiper switch for the Volkswagen Tiguan?

Volkswagen Tiguan rear wiper switch is located on the wiper stalk on the right side of the steering wheel. The front wipers are controlled by moving the stalk up and down, while the rear wiper is controlled by pushing or pulling the stalk. Here is some information about the rear wiper: 1. The rear wiper is the wiper for the rear windshield, commonly equipped on SUVs, MPVs, hatchbacks, and some liftback vehicles. 2. The rear window of a sedan has a relatively large inclination angle, while that of a hatchback has a smaller one. The front wipers are located behind the engine hood, so when high-speed airflow passes over the front of the car, the front wipers are shielded by the hood and remain unaffected. However, the rear wiper lacks such protection, so the impact of high-speed airflow must be considered during installation.
8
5
Share

Can vehicles be inspected in another city?

Nowadays, vehicle inspection can be conducted nationwide, allowing for out-of-town inspections. The following are the required procedures for vehicle inspection: 1. For vehicles within six years of age, bring the vehicle registration certificate and the valid compulsory traffic insurance policy to the designated postal bank inspection agency for direct processing. 2. For vehicles over six years of age, drive to the nearest vehicle inspection station with the registration certificate and valid compulsory traffic insurance policy for on-site testing. Below are the specific items for out-of-town vehicle inspection: 1. Check whether the engine, chassis, body, and their auxiliary equipment are clean, complete, and effective, whether the paint surface is uniform and aesthetically pleasing, whether the main assemblies have been replaced, and whether they match the initial inspection records. 2. Verify whether the vehicle's braking system, lights, exhaust, and other safety performance meet the requirements of relevant regulations. 3. Check whether the vehicle has been modified or altered, and whether the registration certificate, license plate, and vehicle records match the actual condition of the vehicle. 4. Inspect whether the license plate, registration certificate, and the enlarged license plate markings on the vehicle are damaged, altered, or unclear, and whether replacement is needed.
11
3
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.