What is the trick to maintaining clutch control in Subject 2?

1 Answers
KinsleyDella
07/29/25 1:21pm
Subject 2 maintaining clutch control trick is to press the clutch pedal all the way down after getting in the car, shift into first gear, and then gently release the clutch. The following is a related introduction to the Subject 2 test: Test content: includes five mandatory items: reversing into a garage, parallel parking, stopping and starting on a slope, turning at a right angle, and driving on a curved path. Passing standard: According to the "Regulations on the Application and Use of Motor Vehicle Driving Licenses", the Subject 2 test for C1 and C2 driving licenses has a total score of 100 points. Each item has deduction standards for failure (directly deducting 100 points), deducting 20 points, deducting 10 points, and deducting 5 points. A total score of over 80 points is considered a pass.
Was this review help?
20
2
Share
More Forum Discussions

What is the simplest and most accurate method for reverse parking?

Reverse parking simplest and most accurate method: Align the car body: First, align the car body properly, maintaining a distance of about 1 meter from the adjacent car. Reverse parking: Next, start the reverse parking process. Use the right rear wheel to locate the tire point. Once the tire passes the tire point at the upper right corner of the parking space, immediately turn the steering wheel fully. Once the car body is properly aligned, straighten the steering wheel and continue reversing until the car is completely inside the parking space. During the reversing process, make sure to position your head at the middle of the car's width, using your eyes to align the midpoint of the rear of the car with the midpoint of the back of the parking space. This ensures the direction is correct. If you notice the rear of the car gradually drifting to one side, it means the steering wheel hasn't been straightened. Precautions for reverse parking: After getting into the car, adjust the seat and rearview mirrors to ensure the reference points are correct; avoid driving too fast, as high speed may make it difficult to turn the steering wheel in time, increasing the risk of crossing the line.
20
1
Share

What Vehicles Can a C1 Driver's License Drive?

C1 driver's license allows driving small and mini passenger vehicles, light and mini cargo vehicles, light, small, and mini special operation vehicles, as well as the vehicle types permitted by C2 and C3 licenses. C1 Driver's License Exam Subjects: The C1 driver's license is one of the codes for motor vehicle driving licenses. Its exam subjects include four items: traffic regulations and related knowledge, field driving, road driving, and safe and civilized driving common sense. A driver's license is a certificate required by law for motor vehicle drivers. Precautions: Driving a motor vehicle requires certain driving skills. Without these skills, driving a motor vehicle arbitrarily may lead to traffic accidents. Generally, people without a license cannot drive on the road.
9
1
Share

Is driving at 100 km/h on a highway with an 80 km/h speed limit considered speeding?

Driving at 100 km/h on a highway with an 80 km/h speed limit is considered speeding. For roads with two lanes in the same direction, the minimum speed for the left lane is 100 km/h; for roads with three or more lanes in the same direction, the minimum speed for the left lane is 110 km/h, and the minimum speed for the middle lane is 90 km/h. If the speed limit indicated by road signs conflicts with the aforementioned lane speed regulations, drivers should adhere to the speed limit indicated by the road signs. On highways, the speed of small passenger vehicles must not exceed 120 km/h, other motor vehicles must not exceed 100 km/h, and motorcycles must not exceed 80 km/h.
7
4
Share

What are the reasons for the engine oil pressure warning light to come on?

The reasons for the engine oil pressure warning light to come on include insufficient oil quantity, low oil viscosity, clogged oil passages, and electrical circuit faults. Insufficient oil quantity: When the oil reserve in the oil pan is low, the oil pump may contain air and fail to pump oil, leading to a drop in oil pressure. If the engine's oil storage is too low, the lubrication system will have little or no oil, resulting in low oil pressure. Solution: Add oil to the engine. Low oil viscosity: The higher the viscosity of the oil, the higher the oil pressure; conversely, the lower the viscosity, the lower the oil pressure. Solution: Replace the engine oil. Clogged oil passages: If the oil passages are blocked by sludge or other debris, the oil pressure may decrease. Solution: Clean the oil passages. Electrical circuit faults: Faults in the oil pressure sensor, pressure gauge, or electrical circuit can cause low oil pressure. Solution: Replace the oil pressure sensor, pressure gauge, or circuit. The above summarizes the main causes of low engine oil pressure and their solutions. Car users can refer to this article for troubleshooting during vehicle maintenance.
6
3
Share

Where is the radar control box located in the Santa Fe?

The radar control box of the Santa Fe is located on the right side of the trunk. The reverse radar, also known as the 'reverse collision avoidance radar' or 'parking assist device,' mainly consists of ultrasonic sensors, a controller, and a display. When reversing, it utilizes the principle of ultrasound. The sensor installed on the rear bumper emits ultrasonic waves that reflect off obstacles, and the system calculates the actual distance between the vehicle and the obstacle, then alerts the driver, making parking or reversing easier and safer. Relevant information is as follows: 1. The main function of the ultrasonic sensor is to send and receive ultrasonic signals, which are then input into the main unit and displayed on the display device. 2. The controller processes the signals to calculate the distance and direction between the vehicle and the obstacle. 3. The display or buzzer alerts the driver when the sensor detects that the distance between the car and the obstacle reaches a dangerous level, issuing warnings through the display and buzzer.
9
4
Share

How to use the Volkswagen Bora auto start-stop function?

The Volkswagen Bora auto start-stop switch is located at the lower left of the gear lever button area, using a mechanical button. To turn it off, simply press the button. Tips for using the Volkswagen Bora auto start-stop function: 1. The auto start-stop function needs to be manually turned off by the driver each time the car is started. If you want to permanently disable it, you need to visit a 4S dealership for settings. 2. Disable the auto start-stop function when starting on a slope, as the slow response may cause the car to roll back, creating a hazard. Additional notes on using auto start-stop and auto hold: 1. The auto start-stop function temporarily turns off the engine, during which you must keep your foot on the brake pedal. Once the pedal is released, the engine restarts. 2. The auto hold function compensates for the shortcomings of auto start-stop by locking the wheels, eliminating the need to keep your foot on the brake. When you press the accelerator, the auto hold effect is released, and the car will continue moving.
2
2
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.