What is the top speed of the Haval H6?

2 Answers
LeEvan
07/28/25 7:55pm
The top speed of the Haval H6 is 190km/h. The top speed refers to the maximum driving speed that a car can achieve on a well-leveled road surface (concrete or asphalt). It is the speed at which the driving resistance and driving force are balanced under windless conditions on a flat road surface, and it is one of the three evaluation indicators of a car's dynamic performance. Factors affecting the top speed: The top speed is obtained on a flat and windless road surface with zero acceleration, so the gradient resistance and acceleration resistance are zero. Therefore, the main resistance factors affecting the top speed are air resistance and rolling resistance. The point of top speed: When the driving force is balanced with the rolling resistance and air resistance, the car reaches its top speed. Therefore, the intersection point of the driving force line and the resistance line corresponds to the top speed.
Was this review help?
7
5
Share
NadiaLee
08/12/25 12:46am
I remember my Haval H6 has a claimed top speed between 170 to 180 km/h, depending on the model configuration - like the 1.5T turbocharged version. But as a veteran driver who's owned this car for years, I rarely push it to the limit since 120 km/h is sufficient for daily highway use. Speeding carries too many risks - loss of control, longer braking distances, and potential tickets. The car maintains decent stability at high speeds, though wind noise becomes noticeably louder and fuel consumption spikes. Safe driving habits matter more; I always anticipate road conditions and maintain reasonable speeds. Ultimately, top speed is just a number - never let the pursuit of speed compromise safety fundamentals.
Was this review help?
9
4
Share
Expand All
More Forum Discussions

Where is the BMW X1 battery located?

The battery of the BMW X1 is located under the hood of the car. Open the hood and you can see it in the upper left corner. The working principle of the battery is to convert chemical energy into electrical energy. It is a battery that mainly uses lead and its oxides as electrodes and sulfuric acid solution as the electrolyte. You can find the battery by following these steps: 1. Park the vehicle steadily to avoid rolling. 2. Press the one-touch start button to turn off the engine. 3. Confirm that the engine has stopped running. 4. Open the driver's side door. 5. Pull the hood release lever twice. 6. Open the front hood. 7. The battery is located near the air filter.
10
3
Share

What are the differences between Borui and Borui GE?

Borui and Borui GE are similarly priced, but Borui has slightly better configurations than Borui GE. The differences between the two are as follows: 1. The exterior design of Borui GE is consistent with Borui, but the interior of Borui GE has undergone significant changes: Borui GE features a full LCD instrument panel and is equipped with a yacht-style electronic gear lever. 2. Different models: Borui GE is a hybrid model, while Borui is a pure fuel version. 3. Different transmissions: Borui GE is equipped with a 7-speed dual-clutch transmission across the entire lineup, while Borui is equipped with a more stable 6-speed automatic transmission. 4. Different body dimensions: The body dimensions of Borui are 4956/1861/1513mm in length, width, and height, with a wheelbase of 2850mm. The body dimensions of Borui GE are 4986/1861/1513mm in length, width, and height, with a wheelbase of 2870mm. Borui GE has a longer body and a longer wheelbase.
14
5
Share

How to Open the Trunk of a Malibu?

The trunk can be opened or closed either electrically or via remote control. There are four steps to open the trunk of a Malibu: 1. Locate the trunk switch at the lower left corner of the driver's compartment. 2. Pull the trunk switch upward to open the vehicle's trunk. 3. Press the button on the car's remote key to also open the trunk. Below is additional information about the Malibu: 1. Body dimensions, with a wheelbase of 2.7 meters. 2. In terms of power, it is equipped with an Ecotec 2.0L or 2.4L SIDI direct-injection naturally aspirated engine, paired with a 6-speed automatic transmission.
1
2
Share

Where is the USB port of Trumpchi GM8?

There are two USB ports in the Trumpchi GS8, one in the front and one in the rear. The specific locations are as follows: 1. The front USB port is located below the center console, in front of the gear lever. 2. The rear USB port is located behind the armrest box. Precautions for using the USB port are as follows: 1. Charging is only possible when the car engine is started to avoid damage to electrical devices due to unstable power supply. 2. Do not connect too many electrical devices to avoid overloading and damaging the car battery and generator. 3. Do not use the USB port during thunderstorms to avoid lightning accidents. 4. Do not use the USB port in humid environments. Rust or water stains may cause the USB drive to fail to connect properly.
1
2
Share

Where is the Cabin Air Filter of the Soueast DX7 Located?

The cabin air filter of the Soueast DX7 is located inside the glove box on the passenger side. After opening the glove box, you can see the cabin air filter, which has the model number LAK948. Generally, it should be replaced every 8,000 to 10,000 kilometers. Below is some relevant information about the cabin air filter: It is a filter used for air purification inside the car cabin, made of highly efficient adsorption materials, such as activated carbon composite fabric combined with long-fiber non-woven fabric. The compact structure effectively filters smoke odors, pollen, dust, harmful gases, and various odors. The filter can also efficiently filter and adsorb particulate impurities, achieving oil filtration and air purification while effectively removing organic gases such as TVOC, benzene, phenol, ammonia, formaldehyde, xylene, and styrene.
10
1
Share

How to Replace the Battery of a Bestune B70 Key?

Here are the steps to replace the battery of a Bestune B70 car key: 1. Press the circular button on the side of the car key and pull out the mechanical key. 2. Use a screwdriver to pry open the gap at the top of the key. 3. Take out the key circuit board, remove the old battery, place the new battery with the positive side facing up into the slot, and gently push the battery until it is completely secured. 4. Cover the key circuit board back onto the key, align the two separated halves of the key properly, press both sides of the key with your hands until the upper and lower parts are completely fitted together, then insert the mechanical key back into the key gap to complete the process.
19
1
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.