What is the tire pressure for Volkswagen Lavida?

2 Answers
RyanAnn
07/24/25 11:16pm
Volkswagen Lavida's tire pressure ranges from 2.3 to 2.5 bar. You can check the standard tire pressure for Lavida on the back of the fuel filler cap. Both over-inflation and under-inflation can shorten the tire's lifespan. Under-inflation increases tire deformation, leading to sidewall cracks, excessive heat, rubber aging, increased tire contact area, and accelerated shoulder wear. Over-inflation causes excessive stretching of the tire cords, reducing elasticity and increasing the load on the car while driving. The dimensions of the Volkswagen Lavida are 4605mm in length, 1765mm in width, 1460mm in height, with a wheelbase of 2610mm.
Was this review help?
4
0
Share
StDawson
08/10/25 3:20pm
The tire pressure of the Volkswagen Lavida is generally around 2.2 to 2.4 bar, equivalent to 32 to 35 psi, depending on your car's configuration and usage. The most common place to check the standard value is on the label attached to the inside of the driver's door frame, which will list recommendations for different conditions like unloaded and fully loaded. If the tire pressure is too high, driving feels stiff and bumpy, and it can cause excessive wear on the center of the tire; if it's too low, steering becomes sluggish, and the car is more prone to skidding in wet conditions. With over ten years of driving experience, I make it a habit to check the pressure monthly with a simple gauge, preferably when the tires are cold, as temperature changes can affect the readings. Don’t underestimate this detail—proper tire pressure can extend tire life by a year or two and even save fuel. Pay extra attention to adjustments during seasonal changes, especially in summer or winter.
Was this review help?
19
4
Share
Expand All
More Forum Discussions

Where is the internal and external circulation of the 2017 Lavida?

The internal and external circulation of the 2017 Lavida is located next to the air conditioning control panel on the dashboard. The following is an introduction to the car's internal and external circulation: Introduction to external circulation: It uses a fan to draw air from outside the car into the interior, meaning the air passages between the outside and inside of the car are connected. The air blown by the fan comes from outside the car, and even if the fan is not turned on, airflow is still drawn into the car while driving, replenishing fresh air inside the car. Introduction to internal circulation: It closes the airflow passage between the inside and outside of the car. Without the fan, there is no airflow circulation, and when the fan is turned on, the airflow drawn in comes only from inside the car, forming an internal airflow circulation within the vehicle.
12
0
Share

What are the restrictions of Wuling sealed window vans?

Wuling sealed window vans have an obvious exterior restriction - all windows except the first row are completely sealed, hence the name "sealed window van". Essentially a cargo-type microvan, but compared to regular microvans, the sealed window version is longer and uses heavier-duty rear leaf springs than standard microvans to better handle heavy loads. Here's an extended introduction: Window introduction: Car windows are an essential component of the vehicle body, designed to meet requirements for interior lighting, ventilation, and visibility for drivers and passengers. Windows are categorized by installation position: front/rear windshields, side windows, and door windows. The design structure and quality of windows significantly impact driver visibility, passenger comfort, exterior aesthetics, and aerodynamic characteristics. Window structures are typically curved and sealed, with rubber sealing strips connecting the window frame to the glass. These seals provide both sealing and cushioning functions to prevent windshield damage when body forces cause frame deformation.
19
1
Share

Where is the urea nozzle located?

Urea nozzle is located on the exhaust pipe of diesel vehicles. The function of urea nozzle: quantitative injection of urea aqueous solution for exhaust after-treatment, which can reduce the emission of nitrogen oxides. Urea nozzle is a vulnerable part and needs to be cleaned and replaced frequently. Methods for cleaning urea nozzle: 1. Ultrasonic cleaning, using a small ultrasonic cleaning machine; 2. It is recommended to use hot water as cleaning liquid, and immerse the injection end into the liquid; 3. The cleaning time should be more than 15 minutes; 4. Perform functional test to drive the nozzle while cleaning it with ultrasonic, the cleaning effect will be better. In addition to mastering the correct method of cleaning urea nozzle, it is also important to remember not to use inferior urea solution. Because when the purity of urea solution is not enough, and there are impurities such as particles, heavy metal ions, and minerals, it will cause nozzle blockage failure and bring unnecessary economic losses.
9
1
Share

What Causes Sudden Stalling at Low Speeds?

Reasons for sudden stalling at low speeds: 1. Throttle sticking or deformation due to external force can easily cause stalling; 2. Open circuit, short circuit, or burn-out aging of the stepper motor can lead to low-speed stalling; 3. Fuel system issues, such as insufficient fuel pressure or fuel pump failure, may also result in stalling; 4. Clogged fuel injectors, which lead to poor fuel atomization and abnormal engine operation, can cause stalling; 5. Igniter burn-out, due to ignition voltage reaching tens of thousands of volts and oil accumulation at the ignition coil end, can cause abnormal ignition and stalling. If stalling occurs during deceleration or braking, you can increase braking force while paying attention to the surrounding situation. If possible, change lanes to bypass obstacles ahead. Since there is no power steering at this time, steering will feel heavier.
10
4
Share

Can red and blue antifreeze be used together?

Different colors should not be mixed randomly, and they should never be mixed with other maintenance fluids like windshield washer fluid. Here is some relevant information about antifreeze: 1. Antifreeze has five functions: cooling, antifreeze, anticorrosion, lubrication, and cleaning. Among these, the primary functions are antifreeze and cooling, which maintain the engine at normal operating temperatures and prevent freezing in extremely cold weather. To meet these working conditions, antifreeze is manufactured with various combinations of ingredients and additives. 2. During the manufacturing process, manufacturers add different colored dyes to antifreeze to distinguish between different formulations. This serves not only to remind users that antifreeze is toxic and should not be ingested but also to warn against mixing different types. Different colors represent different formulations, and when antifreeze of different formulations is mixed, the chemical stability of the mixture may change once the engine reaches high operating temperatures. This can lead to reduced cooling and antifreeze performance, corrosion or crystallization in the cooling system, and in some cases, even the release of toxic gases.
15
5
Share

Can a Car Battery Charge at Idle Speed?

Yes, a car can charge its battery while idling in place. When the battery charging indicator light on the dashboard is off, it indicates that the car is charging. If the light stays on, it signifies a charging fault, and the vehicle should be taken to a repair shop for inspection. Here are the relevant details: 1. The car charging process essentially involves the engine driving the alternator (generator) to generate electricity, which is then rectified and regulated to provide a certain voltage to the battery. Typically, this voltage is slightly higher than the battery voltage (e.g., 14V, whereas a normal battery is usually 12V), enabling constant voltage charging. 2. At idle speed, although the engine speed is low, it still drives the alternator to work, producing a stable DC voltage. Since the battery power is relatively not that large, charging is possible at idle speed, albeit at a slightly slower rate.
6
4
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.