What is the tire model specification of the Zhijun?

2 Answers
DeCarlos
07/29/25 1:12pm
Zhijun's original tire configuration model is 195/60R14. The first number 195 indicates that the tire width is 195MM, 60 means the aspect ratio of the tire section is 60%, that is, the section height is 60% of the width, the letter R stands for radial tire, and 14 represents the rim diameter is 14 inches. Zhijun has a top speed of 187km/h, accelerates from 0 to 100km/h in 12.5 seconds, and has a fuel consumption of 7.9L per 100km. In addition to the model, the tire is also marked with the following common data: Tire cord material: represented by Chinese pinyin, such as M-cotton cord, R-rayon cord, N-nylon cord, G-steel cord, ZG-steel radial cord tire. Speed rating: indicates the maximum speed at which the tire can carry the specified load under specified conditions. Letters A to Z represent the certified speed ratings of tires from 4.8km/h to 300km/h. Commonly used speed ratings are: Q: 160km/h; H: 210km/h; V: 240km/h; W: 270km/h; Y: 300km/h; Rim specification: indicates the rim specification that matches the tire. For practical use, such as standard rim 5.00F.
Was this review help?
7
1
Share
Daedalus
08/14/25 3:04am
I've been driving a Volkswagen Santana for almost ten years and am very familiar with its tires. The factory standard size is 195/65 R15, which means the tire width is 195 millimeters, the height is 65% of the width, and the wheel diameter is 15 inches. This size provides good stability—no drifting on highways and easy handling in turns. For daily driving, I make it a habit to check the tire pressure every month, adjusting it to around 2.2 bar as indicated on the door frame. Too high or too low pressure increases fuel consumption and risks. When the tread depth falls below 1.6 mm, it's time to replace the tires. Last time I replaced them, I chose a durable brand in the same specification, which was both cost-effective and hassle-free. If upgrading to larger wheels, like 16 inches, the size must be adjusted accordingly to avoid speedometer inaccuracies and safety issues. For rainy conditions, tires with better drainage patterns are recommended for added confidence on wet roads.
Was this review help?
19
1
Share
Expand All
More Forum Discussions

What Causes the Metallic Clanking Sound When Front Wheels Go Over Potholes?

The reasons for the metallic clanking sound when front wheels go over potholes: 1. Engine noise: There are many possible sources of abnormal noise in the engine compartment. Most people can identify it as coming from the engine compartment based on the sound, usually presenting as a sharp metallic screech or a howling noise. 2. Transmission noise: If there is a 'rustling' sound inside the transmission while driving, which disappears when the clutch or accelerator is pressed, and there is a whistling-like sound during gear shifts. 3. Wear-related noise: When pressing the accelerator or brake while driving, there may be some minor abnormal noises from certain parts of the vehicle. These sounds are usually not loud and do not affect normal driving, but they can cause slight concern about potential faults.
9
2
Share

What to Pay Attention to When Rescuing Fracture Victims?

Do not move the fractured part of the body. Below is an introduction to Subject 4: 1. Exam Content: The exam content of Subject 4 mainly includes safe and civilized driving operation requirements, safe driving knowledge under adverse weather and complex road conditions, emergency handling methods for situations like tire blowouts, and post-accident handling knowledge. Subject 4 is also known as the Subject 4 theory test or driver theory test, assessing 'driving ethics.' 2. Exam Scoring: The questions for Subject 4 are selected from a pool of 1,240 questions, with 50 questions chosen proportionally for the exam, including 22 true/false questions, 23 single-choice questions, and 5 multiple-choice questions. The questions are mainly presented in the form of cases, pictures, animations, etc. The total score is 100, with each question worth 2 points, and a passing score of 90. The exam duration is 45 minutes.
6
4
Share

What Causes Antifreeze to Fade in Color?

The reasons for antifreeze fading in color include prolonged use leading to oxidation reactions, contamination by other liquids, or deterioration and impurity accumulation in the antifreeze. When antifreeze color fading is observed, it is recommended to replace the antifreeze. A lightened color indicates that the antifreeze has begun to deteriorate. The main components of antifreeze are 50% pure water, 40% methanol, and 10% other substances. Antifreeze is generally categorized into three types: ethanol-water, glycerol-water, and ethylene glycol-water. Method for replacing antifreeze: Before completely replacing the antifreeze, conduct a thorough inspection to check for any signs of leakage or cracks in the pipes, with particular attention to the five-way hose. The five-way hose is named for its five connections to various parts, and antifreeze is distributed to different parts of the car through this hose to perform its function. If there is any leakage of antifreeze in this section, replace the hose or resecure the connections as needed. Drain the old antifreeze, then flush the liquid channels with clean water. Add clean water to the antifreeze reservoir, then continuously flush the engine cooling system with water. Start the engine and let it idle for 3 to 5 minutes to circulate the water. Initially, the water draining from the reservoir may have a faint pink color. Continue adding clean water until the outflowing water is clear. Remember to remove the heater hose and drain the water from the heater core. After draining for about an hour, add the new antifreeze through the radiator hose to allow it to flow quickly into the radiator. Then, add another container of antifreeze to the antifreeze reservoir until it is nearly full. Start the engine and let it run for about 10 minutes. As some air is expelled from the cooling system, the fluid level will drop. Add more antifreeze until it reaches the "MAXT" mark on the reservoir.
15
5
Share

Should the front radar be installed with 2 or 4 sensors?

Two front sensors are sufficient, and high-end original vehicles typically come with two. Below is additional information about radar: 1. Automotive Radar: Consists of ultrasonic sensors (commonly known as probes), a controller, and a display (or buzzer). It informs the driver about surrounding obstacles through sound or more intuitive displays, alleviating the difficulties caused by checking front, rear, left, and right when parking, reversing, or starting the vehicle. It also helps eliminate blind spots and unclear vision, enhancing driving safety. 2. Function of Front Radar: The front radar sensors are installed on the front bumper, radiating at approximately a 45-degree angle to search for targets in all directions. The biggest advantage is the ability to detect obstacles below the bumper that are difficult for the driver to see from inside the car, such as flower beds or playing children, and provide an alert.
12
5
Share

What is that blinking light after the car is turned off?

That is the anti-theft indicator light, which flashes when the vehicle's anti-theft system is activated. The flashing of the anti-theft indicator light indicates that the vehicle's anti-theft system is active and operational. Generally, when the owner presses the lock button on the smart key, the car's anti-theft system is activated, and the anti-theft light will flash. Here are the details: How the car anti-theft light works: If the car engine anti-theft light flashes at a frequency of once every 1 to 2 seconds, it is normal. This means that the car's engine has entered the anti-theft state, and the engine anti-theft system is functioning. This is a normal phenomenon, and the owner does not need to deactivate it. Moreover, the power consumption is minimal, and it poses no problem for the battery.
17
0
Share

Which button is for car air conditioning cooling?

The AC button inside the car is the cooling switch. The AC button controls the air conditioning compressor. In summer, when using air conditioning, press the AC button to activate cool air. However, the heating system simply utilizes the car's internal heat circulation and does not require the air conditioning compressor to be activated. Therefore, to turn on the heating, you only need to adjust the air conditioning controls without pressing the AC button. Below is more information about car air conditioning: 1. Function: The car air conditioning system (air-conditioning-device), referred to as car AC, is used to adjust and control the temperature, humidity, air cleanliness, and airflow inside the car cabin to optimal conditions, providing a comfortable environment for passengers and reducing travel fatigue. 2. AC layout: Different types of air conditioning systems have varying layouts. Currently, most cars use an integrated heating and cooling air conditioning system. This layout combines the evaporator, heater radiator, centrifugal blower, and control mechanism into a single unit, known as the air conditioning assembly. 3. AC components: Modern air conditioning systems consist of a refrigeration system, heating system, ventilation and air purification devices, and a control system.
17
3
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.