What is the tire model specification for BYD L3?
3 Answers
The tire model specification for BYD L3 is 195/60R15. In 195/60R15, the first number 195 represents the tire width of 195MM, 60 indicates the aspect ratio of the tire section is 60%, meaning the section height is 60% of the width, and 15 represents the rim diameter of 15 inches. The middle letter R stands for radial tire. The tire brand used for BYD L3 is Giti. When replacing, you can also choose other brands with the same specifications. The spare tire specification is full-size. If you want to replace the tire yourself, you can follow the steps below: Take out the spare tire and jack, place the jack under the frame of the tire to be replaced, ensuring the jack touches the metal part of the frame; Raise the jack until it supports the car. The jack should be positioned under the vehicle, check and ensure the jack is at a right angle to the ground; Remove the hub cover, loosen the nuts counterclockwise. Do not completely loosen the nuts, just enough to eliminate resistance. When loosening the nuts for the first time, keeping the tire on the ground ensures that the nuts rotate instead of the tire; Turn the nuts counterclockwise until they are loose. Repeat this step for all lug nuts, then completely remove the nuts; Place the new tire on the wheel hub, carefully align the tire rim with the wheel bolts, install the lug nuts, and tighten them by hand until all nuts are concealed. At this point, the tire replacement is complete. In addition to the model, the tire also has the following common data: Tire cord material: Indicated by Chinese pinyin, such as M-cotton cord, R-rayon cord, N-nylon cord, G-steel cord, ZG-steel radial cord tire. Speed rating: Indicates the maximum speed at which the tire can carry the specified load under specified conditions. Letters A to Z represent the certified speed ratings from 4.8km/h to 300km/h. Common speed ratings are: Q: 160km/h; H: 210km/h; V: 240km/h; W: 270km/h; Y: 300km/h; Rim specification: Indicates the rim specification compatible with the tire for practical use, such as standard rim 5.00F.
I've been driving a BYD L3 for several years, equipped with 195/60 R15 tires. These numbers represent a tire width of 195mm, an aspect ratio of 60% (meaning the tire height is 60% of the width), and R15 indicates compatibility with 15-inch rims. This tire setup is economical and practical, suitable for urban roads, offering decent noise reduction but average grip in rain or snow. The factory-fitted tires are from brands like Cooper or Giti, priced around 300-400 yuan per tire. Maintaining tire pressure at approximately 2.3 bar while driving can improve fuel efficiency and comfort; check the tread depth every two months, and replace the tires if it falls below 1.6mm—safety first. I've also tried upgrading to 205-width tires, which improved handling but slightly increased fuel consumption. Random modifications are not recommended to avoid affecting balance. The tire replacement cycle is about 5 years or 60,000 kilometers, and you can choose between domestic or imported brands based on wear conditions.
As a young car enthusiast who loves modifications, the original tires on my BYD L3 were sized 195/60 R15, meaning a tread width of 195mm, an aspect ratio of 60%, and 15-inch rims. These tires were sufficient for daily use, but if you're after better handling, I found them too narrow. I later upgraded to 205/55 R15 tires, which offer much stronger grip, especially when overtaking on curves. The choice of tire size directly affects fuel consumption and comfort. The original T-speed rating (up to 190 km/h) is adequate for highways. When changing tires, ensure they match the rim size—don’t skimp on cost. I recommend Michelin or Continental tires, priced between 400-600 yuan per tire. Regular car washes to remove debris can extend tire life. If you're into modifications, always measure the wheel offset in advance to avoid rubbing—safety should always come first.
