What is the tire model of the Dongfeng Peugeot 301?

1 Answers
ThomasAnn
07/29/25 7:47pm
Peugeot 301 tire model specifications: 195/55R16, 195mm. The following is an introduction about tires: 1. The international standard tire code represents the section height and aspect ratio in millimeters as a percentage. It is followed by: tire type code, rim diameter (inches), load index (allowable load mass code), and allowable speed code. 2. Tire size is printed on the sidewall, and there are two representation methods, such as 34*7 or 7.50-20. The former is for high-pressure tires, and the latter is for low-pressure tires. There are also many other markings, for example, D is used for light vehicles, F for medium vehicles, G for standard vehicles, and H, L, J for large luxury and high-performance vehicles. 3. If an R is printed on the sidewall, such as 175R13, it indicates that the tire is a radial tire, with a width of 175mm (6.9 inches), mounted on a wheel with a rim diameter of 13 inches (330mm), and the word RADIAL is usually also engraved.
Was this review help?
5
3
Share
More Forum Discussions

What is the best engine oil for Buick Envision?

Buick Envision's original engine oil specification is 5W-30. For later maintenance, you can choose Castrol, Shell, or Mobil 1 Silver, all of which are fully synthetic oils. The viscosity of engine oil changes with temperature, so special attention should be paid to its performance under both low and high temperatures. For example, in 5W-30, the first number indicates low-temperature fluidity: 5W means it can withstand temperatures as low as -30°C. The smaller this number, the better the low-temperature fluidity, making cold starts smoother. The latter number represents the oil's kinematic viscosity at 100°C. The higher this number, the better the oil maintains its viscosity at high temperatures, which can also be understood as better lubrication performance under high-temperature conditions. The method for changing the engine oil in a Buick Envision is as follows: Wait for the engine temperature to drop, allowing the oil to flow back into the oil pan. Use a wrench to loosen the oil drain plug and place an oil pan underneath to catch the old oil until it stops flowing. Start the engine and let it run for 30 seconds to allow the oil in the main oil passages to drain out. Use a specialized wrench to remove the oil filter. Apply oil to the seal of the new oil filter and tighten it clockwise by hand. Add the new oil through the engine's valve cover oil filler port, typically filling about three-quarters of the oil container. Start the engine and let it run for 5 minutes, then check for any leaks around the oil drain plug and oil filter. If leaks are found, repairs should be made. After stopping the engine, pull out the dipstick to check that the oil level is within the standard range.
13
4
Share

How many liters of engine oil does the Edge require?

The Edge 2.0T requires 5.5 liters of engine oil, while the 2.7T requires 6.5 liters. The Edge uses Ford's specialized engine oil, with the original factory specification being 5W30 semi-synthetic oil. The viscosity of engine oil changes with temperature, so special attention should be paid to its performance under low and high temperatures. For example, in 5W-30, the first number indicates low-temperature fluidity. 5W means it can withstand temperatures as low as -30°C. The smaller this number, the better the low-temperature fluidity, resulting in smoother cold starts for the car. The second number represents the kinematic viscosity of the oil at 100°C. A higher number means the oil can maintain its viscosity index better at high temperatures, which can also be understood as better lubrication performance under high-temperature conditions. The method for changing the Edge's engine oil is as follows: Wait for the engine temperature to drop, allowing the oil to flow back into the oil pan. Use a wrench to loosen the oil drain plug and place an oil pan underneath to catch the old oil until it stops flowing. Start the engine and let it run for 30 seconds to allow the oil in the main oil passage to drain out. Use a specialized wrench to remove the oil filter. Apply oil to the seal of the new oil filter and tighten it clockwise by hand. Pour the new oil into the engine through the valve cover oil filler port, typically filling about three-quarters of the oil bottle. Start the engine and let it run for 5 minutes, checking for leaks around the oil drain plug and oil filter. If any leaks are found, repairs should be made. After stopping the engine, pull out the dipstick to ensure the oil level is within the standard range.
2
0
Share

Where is the USB port in the Golf?

The USB port in the Golf is located inside the storage compartment on the front center console. Since the vehicle provides relatively low voltage, the car charger only requires an overload protection circuit. A fuse is designed at the front end of the car charger socket, which immediately blows when the current exceeds the capacity of the overload protection circuit, thereby providing protection. The Golf is a classic hatchback compact family car launched by FAW-Volkswagen, with dimensions of 4199mm in length, 1786mm in width, and 1479mm in height, and a wheelbase of 2578mm. The car features a functional electric sunroof, a three-spoke genuine leather multifunction steering wheel, and advanced noise-reduction silent design technology.
2
1
Share

Is the fuel consumption of the Changan CS75 Plus high?

The comprehensive fuel consumption of the Changan CS75 Plus is 6.5-8.1L/100km. Currently, there are 5 models of the Changan CS75 Plus on sale. The automatic flagship model and automatic navigation model have a comprehensive fuel consumption of 8.1L/100km. The automatic premium model, automatic luxury model, and automatic elite model have a comprehensive fuel consumption of 6.5L/100km. The above figures are the NEDC comprehensive fuel consumption, which is the fuel consumption data measured under the NEDC test procedure. The actual fuel consumption is higher than this value, ranging from 9.2-12.0L/100km. The level of a car's fuel consumption is directly related to five major factors: driving habits, the car itself, road conditions, natural wind, and environmental temperature. Specific factors that can increase a car's fuel consumption are as follows: Driving habits: Aggressive driving, such as sudden acceleration, frequent overtaking, and not easing off the throttle before encountering a red light, can increase fuel consumption. The car itself: Cars with larger displacements generally consume more fuel than those with smaller displacements because larger displacements usually mean greater power, requiring more gasoline to burn and perform work. Cars with greater weight also consume more fuel because greater weight requires more driving torque. Road conditions: Driving on dirt roads, muddy roads, soft surfaces, or mountainous roads increases resistance and fuel consumption. Natural wind: Driving against the wind or on windy days increases the car's resistance and fuel consumption. Low environmental temperature: When the engine block temperature is low during a cold start, the injected gasoline is less likely to atomize, requiring more gasoline to be injected for combustion, thus increasing fuel consumption. Additionally, at low temperatures, the engine's computer will control the engine to run at higher RPMs to warm up, which also increases fuel consumption.
4
2
Share

What is the reason for the fuel gauge not displaying the fuel level?

The reasons for the fuel gauge not displaying the fuel level are: 1. Abnormalities in the fuel float and ignition wire; 2. Computer signal failure; Solutions: 1. Turn the key off and on again. If this doesn't work, replace the fuel float; 2. It is recommended to go to a repair shop for maintenance. The method to check the fuel gauge is: 1. On the dashboard, the fuel gauge is commonly found in pointer or electronic forms; 2. The letters F and E are marked at both ends. Pointing to F indicates the fuel tank is full, pointing to E indicates the fuel is empty, and pointing to the middle indicates there is half of the fuel left; 3. When the fuel gauge light comes on, the fuel gauge is already pointing close to the letter E.
12
0
Share

What are the details and techniques for the B2 Subject 3 driving test?

Here are the relevant details and techniques for the B2 Subject 3 test: Starting: Before starting, check if the doors are fully closed, adjust the seat and mirrors, fasten the seatbelt, check the parking brake and gear, then start the engine. Check the dashboard, observe the interior and exterior mirrors, turn your head to observe the traffic behind, turn on the turn signal, shift gears, release the parking brake, and start moving. The starting process should be smooth, without jerking, rolling backward, or stalling. Changing lanes: Before changing lanes, correctly turn on the turn signal, observe the traffic behind through the interior and exterior mirrors, and change lanes only when it is safe to do so. After completing the lane change, turn off the turn signal. When changing lanes, judge the safe distance of the vehicle, control the driving speed, and do not hinder the normal driving of other vehicles.
20
3
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.