What is the tire model for the 2021 Honda CR-V?

2 Answers
McGabrielle
09/07/25 5:33am
2021 Honda CR-V comes with three tire models: 235/65R17, 235/60R18, and 235/55R19. Precautions for tire usage: Regularly inspect the tire surface for cracks, deformations, or other defects; park on level ground and avoid parking on roads with large, sharp, or pointed stones; do not use water to cool overheated tires—tires can overheat during prolonged or high-speed driving in summer, leading to increased pressure. In such cases, park to allow the tires to cool naturally. Never release air to reduce pressure or splash water to cool them, as this can cause abnormal aging of the tire rubber; avoid sudden braking—maintain appropriate speed, pay attention to road conditions, pedestrians, and other vehicles, and prepare for braking to reduce frequent or emergency stops; choose good road surfaces—when driving through road construction zones, proceed slowly at low speed while carefully selecting the path. Precautions for tire maintenance: Avoid rapid acceleration or deceleration with new tires, and refrain from excessive steering, as these actions can shorten tire lifespan; keep tires clean; develop a habit of checking tire condition before driving; remember to inflate tires when pressure is insufficient.
Was this review help?
15
1
Share
Colton
09/19/25 4:49am
As an owner of a 2021 Honda CR-V, I did thorough research when changing tires last year. Base models typically use 225/65 R17 tires, while higher trims may upgrade to 235/60 R18. These specifications are indicated on the door jamb label - 225 represents the width in millimeters, 65 is the aspect ratio, and R17 means 17-inch rims. I chose Michelin tires which are quite wear-resistant; after two years of urban driving, the tread depth remains sufficient. If you frequently drive on highways or rough roads, remember to check wear every 10,000 km by inserting a coin into the tread grooves to measure depth. It's advisable to switch to winter tires when snow falls, as insufficient traction may cause skidding and safety risks. Maintain tire pressure around 35 psi during monthly inflation checks - this can extend tire life and reduce fuel consumption by approximately 5%.
Was this review help?
11
2
Share
Expand All
More Forum Discussions

What to do if the Volkswagen Polo steering wheel is locked?

The solution for a locked Volkswagen Polo steering wheel: 1. Start the engine and activate all the vehicle's electronic systems; 2. Press the top of the toggle lever located on the right side of the steering wheel, hold it down without releasing, and continue holding for more than 5 seconds until the steering wheel unlocks. A locked car steering wheel is an emergency response of the car's active anti-theft security system. The Volkswagen Polo is a compact car produced by SAIC Volkswagen. Taking the Polo 2021 Plus 1.5L Manual Panorama Enjoyment Edition as an example, its body dimensions are 4053mm in length, 1740mm in width, and 1449mm in height, with a wheelbase of 2564mm. The body adopts a 5-door, 5-seat hatchback structure, with a fuel tank capacity of 42.5 liters and a curb weight of 1145kg.
2
4
Share

How to Use the Paddle Shifters in the 2020 Buick Regal?

2020 Buick Regal paddle shifter usage method: First, select manual mode, then shift the gear lever to D, and use the paddle shifters to upshift or downshift. The paddle shifters primarily feature a semi-automatic clutch, a gear-shifting device installed in the car. When switched to manual mode, the driver does not need to press the clutch pedal but can shift gears directly via the paddle shifters, making the operation very simple. The Regal is a mid-size sedan under SAIC-GM Buick. Taking the 2020 Regal 552T Elite as an example, its powertrain is equipped with a 1.5L inline four-cylinder turbocharged engine with an aluminum alloy structure, delivering a maximum power of 124kW and a maximum torque of 250Nm, paired with a 9-speed automatic manual transmission.
3
4
Share

Why does only one reverse light illuminate on the 2021 Corolla?

The 2021 Corolla has only one reverse light because this design is intended to better capture the driver's attention. Symmetrical lighting on both sides might cause a numbing effect, leading drivers to mistakenly perceive an oncoming vehicle as moving in reverse. Typically, the reverse light is positioned with the left fog light and right reverse light. This configuration is due to the driver's seat being on the left side in China, allowing better visibility of oncoming vehicles with the fog light on the left, while the right-side reverse light facilitates nighttime parking maneuvers on the right side of the road. The Corolla is a compact car under FAW Toyota. Taking the 2021 Corolla 1.2T S-CVT Pioneer PLUS edition as an example, it is powered by a 1.2L inline four-cylinder turbocharged engine with an aluminum alloy structure, delivering a maximum power of 85kW and a maximum torque of 185Nm, paired with a 10-speed continuously variable transmission.
12
3
Share

Why is shifting from P to R gear very tight?

The reason why shifting from P to R gear is very tight is due to incorrect parking methods: Before the last parking and engine shutdown, because the engine was still running, when the owner shifted from D or R gear to P gear, they had to pass through R gear, which caused the gears to jam. Therefore, when the owner needs to move out of P gear again, it becomes very tight. Solutions for tight shifting from P to R gear: 1. Press the brake to stop, keep the brake pressed, shift from D to N gear, then engage the handbrake with the left foot, release the right foot brake, shift from D to P gear, turn off the engine, and exit the vehicle; 2. When driving, press the foot brake, start the engine, and shift gears to solve the issue. The correct method for parking an automatic transmission car is: 1. Press the brake to slow down and stop; 2. After stopping completely, shift into N gear; 3. Tighten the handbrake; 4. Release the foot brake and confirm the vehicle is stable; 5. Press the foot brake again, shift into P gear, and turn off the engine.
2
1
Share

What is the problem when the rear brake of a motorcycle does not rebound?

Motorcycle rear brake does not rebound due to: rust on the brake rocker arm shaft or brake cable, excessive wear of the brake shoe block, damage to the brake cable wire, deformation or jamming of the brake pedal or handle, or excessive dirt or deformation in the brake lower pump. Braking, also known as stopping, refers to the action of stopping or reducing the speed of running locomotives, vehicles, other means of transport, or machinery. Motorcycles are driven by gasoline engines and are two- or three-wheeled vehicles that rely on handlebars to steer the front wheels. They are lightweight, flexible, and fast, widely used for patrol, passenger and cargo transportation, and also serve as sports equipment. Broadly speaking, motorcycles are divided into street bikes, road racing motorcycles, off-road motorcycles, cruisers, and touring bikes.
7
4
Share

Why does the motorcycle always stall when stopping?

Reasons why the motorcycle always stalls when stopping: 1. There is air leakage in the engine; 2. Incorrect spark plug electrode gap; 3. Clogged idle jet in the carburetor. Solutions: Adjust the throttle adjustment screw and air adjustment screw. If there is still no idle, remove and open the carburetor, use a steel wire with a diameter less than 0.4mm to clean the idle jet and idle air passage, then use an air pump to blow out all the holes, or check if the fuel level in the carburetor float chamber is too low or if there is air leakage in the reed valve or crankcase. A motorcycle is a two-wheeled or three-wheeled vehicle driven by a gasoline engine, steered by handlebars, lightweight and flexible, fast-moving, widely used for patrol, passenger and cargo transportation, and also used as sports equipment. Generally speaking, motorcycles are divided into street bikes, road racing motorcycles, off-road motorcycles, cruisers, and touring bikes.
19
5
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.