What is the thrust of the RD180?

1 Answers
ValerieLee
07/29/25 2:56pm
RD180 rocket engine has a thrust of up to 400 tons. The following are the specific details of the RD180 rocket engine: 1. Working principle: The RD180 rocket engine is a dual-combustion chamber, dual-nozzle rocket engine developed and produced by the Soviet Union/Russia. The RD180 uses kerosene and liquid oxygen as propellants and employs a high-pressure staged combustion cycle. Inheriting the oxygen-rich preburner design from its predecessor, the RD170, the RD180 achieves higher engine efficiency. The movement of the nozzle is supported by four hydraulic cylinders. 2. Application: It is primarily used in the first stage of the Soviet Union's 'Energia' heavy-lift launch vehicle.
Was this review help?
12
5
Share
More Forum Discussions

What is the difference between antifreeze and coolant?

The differences between antifreeze and coolant are: 1. Nature: The full name of antifreeze is antifreeze coolant. It is a type of coolant containing special additives, mainly used in liquid-cooled engine cooling systems. Antifreeze is not entirely equivalent to coolant. Coolant refers to any liquid that can cool the engine, which can be either water or antifreeze. Water, being highly limited by temperature, is considered a very low-grade coolant. 2. Location: Antifreeze and coolant are not added to the same place. Antifreeze is added to the radiator, while coolant is added to the small reservoir next to it, also known as the overflow tank. 3. Function: Besides preventing freezing, antifreeze has other functions such as rust prevention, corrosion inhibition, lubrication, a high boiling point, and minimal scaling, which are features that coolant does not possess.
5
5
Share

What maintenance is required at 80,000 kilometers?

Here are the maintenance items for a car at 80,000 kilometers: 1. Replace engine oil and the three filters. 2. Replace transmission fluid. 3. Replace the generator and fan belts. 4. Replace spark plugs. 5. Replace brake fluid. 6. Replace power steering fluid. 7. Replace the fuel filter. Here is the classification of maintenance levels: 1. Primary maintenance (around 5,000 kilometers): Maintenance operations focused on tightening and lubrication for vehicles that have traveled a certain mileage. Includes checking and tightening bolts and nuts on exposed parts of the vehicle; adding lubricants to specified lubrication points; checking the oil level in various assemblies and topping up lubricants; cleaning air filters, etc. 2. Secondary maintenance (around 10,000 kilometers): Maintenance operations focused on inspection and adjustment for vehicles that have traveled a certain mileage. The scope includes all primary maintenance items, plus inspecting and adjusting the engine and electrical equipment, dismantling and cleaning the oil pan and oil filter, inspecting and adjusting steering and braking mechanisms, dismantling and cleaning front and rear wheel hub bearings, adding lubricants, dismantling and inspecting tires, and performing tire rotation. 3. Tertiary maintenance (around 20,000 kilometers): Maintenance operations focused on disassembly, cleaning, inspection, adjustment, and elimination of potential hazards for vehicles. The scope includes all primary and secondary maintenance items, plus dismantling and inspecting the engine to remove carbon deposits, gum, and cooling system contaminants; disassembling, cleaning, inspecting, and adjusting chassis assemblies as needed to eliminate potential hazards; inspecting the frame and body, or performing rust removal and touch-up painting.
11
3
Share

Will running a yellow light be photographed?

Running a yellow light will be photographed. Regulation introduction: The "Road Traffic Safety Law" stipulates that a yellow light serves as a warning, and motor vehicles should slow down when approaching an intersection. If a vehicle has already crossed the stop line when the yellow light turns on, it may continue to pass. If it has not yet crossed the stop line, it should slow down and stop. The act of rushing through a yellow light is considered a violation of traffic signal rules, and the driver will be fined and penalized with 6 demerit points. Legal basis: According to Article 38 of the "Regulations for the Implementation of the Road Traffic Safety Law," when the green light is on, vehicles are permitted to pass, but turning vehicles must not obstruct the passage of through traffic or pedestrians. When the yellow light is on, vehicles that have already crossed the stop line may continue to pass.
18
4
Share

Is the BYD Qin a hybrid?

BYD Qin offers two models: pure electric and hybrid. Below are the specific details about the BYD Qin: Body dimensions: The length, width, and height are 4765mm, 1837mm, and 1495mm respectively, with a wheelbase of 2718mm. Powertrain: Equipped with a 1.5L naturally aspirated engine, which delivers a maximum power of 81kW at 6000 rpm and a maximum torque of 135 Nm at 4500 rpm. This engine features multi-point fuel injection technology and uses an aluminum alloy cylinder head and block. Suspension: The front suspension employs a MacPherson independent suspension, while the rear suspension uses a torsion beam non-independent suspension.
15
2
Share

What is the fuel consumption of the Mazda Atenza 2.0 and 2.5?

2020 Mazda Atenza 2.0L with 6-speed automatic transmission has a MIIT combined fuel consumption of 6.3-6.4L/100km. 2020 Mazda Atenza 2.5L with 6-speed automatic transmission has a MIIT combined fuel consumption of 7.0-7.1L/100km. Below are the related details: Fuel consumption differences: Poor driving skills can lead to increased fuel consumption. The same car driven by different people will have different fuel consumption. Only by summarizing experience and improving driving skills can the high fuel consumption problem caused by driving techniques be resolved. Precautions: If the fuel consumption is abnormally high, you should promptly visit a repair shop for maintenance, including checking the engine, cylinders, and pistons to identify the specific cause.
19
5
Share

How to Restore Automatic Transmission to Factory Settings?

Here are the steps to restore the automatic transmission to factory settings: 1. Gently press the start button to power on when the engine is cold; 2. With the power on, press the accelerator pedal all the way down and hold for 5 to 10 seconds; 3. Gently press the start button to power off, and do not release the accelerator during the power-off process; 4. After powering off, release the accelerator and wait a few minutes. The transmission will automatically complete the reset. Additional Information: 1. The function of transmission fluid is to keep the shifting system clean and lubricate the transmission components. 2. Symptoms of not changing transmission fluid include decreased power, sluggish response during acceleration, louder engine noise without corresponding speed increase, difficulty starting, and short travel distance when pressing the accelerator at low gears.
19
5
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.