What is the throttle matching channel number for Volkswagen?

1 Answers
GiaAnn
07/29/25 8:03pm
Volkswagen throttle matching channel number is 060. Note: Throttle adjustment matching is only suitable for Volkswagen vehicles equipped with electronic throttle engine systems, and the Santana GLi is not within the matching range. The following is an extended introduction: 1. Basic setting content: When the ignition switch is turned on, adaptive learning can be performed between the throttle control unit and the engine control unit. 2. Basic setting process: During the throttle basic setting, the throttle actuator moves from the maximum position to the minimum position in emergency operation. The engine control unit learns the stop position of the throttle control unit and the comparison curve between the throttle potentiometer and the throttle controller sensor through adaptive learning.
Was this review help?
15
0
Share
More Forum Discussions

How to Handle the Dashboard Display of Vehicle Condition Check in Passat?

When the Passat dashboard displays a vehicle condition check, it indicates that the vehicle requires maintenance. It is best to visit a 4S shop and use a specialized diagnostic computer to reset the maintenance code to 0 in order to clear this display. The manual method to clear the display is as follows: 1. Turn off the ignition. 2. Press and hold the 0.0 button at the bottom right corner with your left hand. 3. Turn on the ignition with your right hand (note: do not release the left hand). 4. At this point, a non-flashing wrench symbol will appear on the dashboard. 5. Release the left hand. 6. Press the button at the bottom left corner once. 7. The wrench symbol will disappear.
19
5
Share

How to Replace the Battery in a Volkswagen Lavida Car Key?

Replacing the battery involves the following steps: 1. Prepare the necessary tools for battery replacement: a flat-head screwdriver, the car key, and the battery. 2. Locate the round button on the side of the car key. Press the round button with one hand while pulling out the mechanical key with the other hand. 3. Hold the key with one hand and the flat-head screwdriver with the other. Find the gap in the middle of the key's top end and insert the flat-head screwdriver into it. Pry the key up and down until a gap is created. 4. Remove the key circuit board, gently push one side of the battery with your finger, and take out the old battery. Place the new battery with the positive side facing up into the battery slot on the key, and gently push it until it is fully secured. 5. Cover the key circuit board back onto the key, align the two separated halves of the key properly, and press both sides of the key with your hands until the upper and lower parts are completely fitted together. Finally, insert the mechanical key back into the key slot.
17
0
Share

How to turn on the high beam on the Sylphy?

The method to turn on the high beam on the Sylphy is as follows: 1. Turn the end of the light control lever forward to the first position—position lights. 2. Turn the end of the light control lever forward to the second position—low beam. 3. In the low beam state, gently push the light control lever forward—switch to high beam (when kept on for a long time, the high beam indicator will appear on the dashboard until switched back to low beam); pull it back—return to low beam. Here is the difference between high beam and low beam: 1. High beam has a higher angle and longer distance, while low beam has a lower angle and shorter distance. 2. You can use high beam when driving on highways or in rural areas without streetlights to expand the field of vision. In urban areas, it is recommended to use low beam.
3
2
Share

What does the exclamation mark inside a triangle displayed on the car represent?

A triangle with an exclamation mark indicates a malfunction in the vehicle's general performance, components, or functions. Common issues include parking sensor failure, fuel cut-off system intervention or malfunction, external light failure, or engine oil pressure sensor failure. Solution: It is necessary to visit a 4S shop for inspection to identify the source of the fault. The exclamation mark is a common fault indicator in vehicles. In addition to the triangle with an exclamation mark, there are four other forms of exclamation mark indicators: a yellow gear with an exclamation mark, a red circle with parentheses and an exclamation mark in the middle, a yellow bracket with a horizontal line and an exclamation mark in the middle, and a yellow bulb with an exclamation mark. Below is a detailed analysis of these four scenarios: Automatic transmission fault: A yellow gear with an exclamation mark is the automatic transmission fault warning light, indicating a transmission fault or transmission lubricant level below the normal range. Transmission fluid should be replaced promptly. Brake system fault: A circle with parentheses and an exclamation mark in the middle represents a brake system warning, mainly indicating a brake system malfunction or low brake fluid level. The brake system should be inspected immediately to avoid accidents. Tire pressure anomaly: A bracket with a horizontal line and an exclamation mark in the middle represents the tire pressure monitoring warning light, which illuminates when the tire pressure is too low. Check the vehicle's tire pressure and restore it to the normal range. Lighting fault: A yellow bulb with an exclamation mark is the lighting fault indicator, signaling a malfunction in the vehicle's lights. Solution: Visit a 4S shop for inspection as soon as possible, or conduct a self-check focusing on commonly used bulbs such as turn signals, fog lights, and interior lighting to identify the issue.
3
0
Share

What is the marking for China V vehicles?

China V emission standard is marked with a "V", which can be found on the vehicle's factory certificate or environmental standard list. Below are specific details about the China V standard: 1. The China Fifth Stage Motor Vehicle Pollutant Emission Standard, abbreviated as "China V Standard", has emission control levels equivalent to the European Union's currently implemented Euro 5 emission standard. 2. China V imposes stricter limits on vehicle emissions such as nitrogen oxides, hydrocarbons, carbon monoxide, and particulate matter. From China I to China IV, each upgrade in the standard reduces single-vehicle pollution by 30% to 50%.
19
5
Share

What Are the Fuel-Saving Tips for Automatic Transmission Cars?

Here are some fuel-saving tips for automatic transmission cars: 1. Gentle Start: After starting the car, let it warm up for about a minute (longer in winter), then gradually accelerate until the temperature normalizes before driving. 2. At Red Lights, Don't Stay in 'D' Gear: Shift to 'N' gear (neutral) when waiting at red lights, which can save about 0.2% fuel. 3. Accelerate Gradually: Avoid flooring the accelerator pedal. 4. Regular Maintenance: Schedule maintenance every 5,000 kilometers at a 4S shop.
12
0
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.