What is the Three Touches in Subject 3?

1 Answers
LeHector
07/30/25 7:57am
The "Three Touches" in the Subject 3 driving test refer to: touching the sensor of the center rearview mirror, the sensor of the left rearview mirror, and the sensor under the seat, while adjusting the seat properly. Below are some tips for the Subject 3 test: 1. Follow the instructions: Listen carefully to the voice prompts during the Subject 3 test and follow them accordingly. Remember not to perform any actions before the voice prompt ends; always wait until the prompt is complete before proceeding. 2. Pay attention to special zones: In many areas, the voice prompts no longer remind candidates of special zones such as school areas, bus stops, and crosswalks. However, candidates must perform corresponding deceleration or yielding actions based on the project signs and road markings. For school zones, apply the brakes within 10 meters of the sign, keeping the speed below 30 km/h. For bus stops, apply the brakes within 10 meters of the sign, keeping the speed below 30 km/h. For crosswalks, apply the brakes to decelerate within 30 meters before the crossing, and stop to yield if pedestrians are passing.
Was this review help?
8
1
Share
More Forum Discussions

How to Remove License Plate Screws?

Method for removing license plate screws: 1. Prepare the tools needed for the removal process; 2. Before removal, check if the cutting disc of the angle grinder is intact and undamaged, then install the cutting disc onto the angle grinder; 3. Plug in the power cord of the angle grinder, hold the handle of the angle grinder with both hands, turn on the angle grinder with your right hand, and make a straight cut on the license plate cover using the angle grinder; 4. Use a flat-head screwdriver to pry off the license plate cover by inserting it into the straight cut made on the license plate. Pry slowly, holding the handle of the screwdriver to avoid injuring your hand; 5. Use a Phillips-head screwdriver to unscrew the screws securing the license plate. Turn gently to avoid stripping the screws on the vehicle; 6. Dispose of the removed waste license plate fasteners promptly by placing them in the appropriate classified trash bin.
8
3
Share

What are the symptoms of a faulty steering gear in the Baojun 560?

The symptom of a faulty steering gear in the Baojun 560 is that the steering wheel does not respond properly. Causes of steering gear failure: Power steering pump failure, steering gear failure, lack of oil, air in the system, or clogged return oil filter in the reservoir. Power steering pump failure: If testing shows that the pump pressure of the power steering pump does not meet the standard value, it is clear that the heavy steering is related to this. First, check whether the flow control valve and valve seat mating surface are tightly sealed, and whether the safety valve steel ball is properly closed. If there is leakage in the flow valve or safety valve, it can be repaired by grinding. Steering gear failure: If testing reveals low hydraulic pressure in the steering gear, the heavy steering is caused by the steering gear. In this case, professional repair services should be sought. Generally, steering gear failures are caused by piston or cylinder barrel damage, or a damaged piston seal ring, which allows the two chambers of the piston to communicate, preventing effective hydraulic pressure buildup. Additionally, damaged sealing rings on the piston circumference or steering screw can also lead to pressure loss and reduced hydraulic pressure. Lack of oil or air in the system: If the power steering system lacks oil, air can enter the system, resulting not only in heavy steering but also noise during steering. In this case, follow the oil refill and air bleeding procedure to remove the air.
20
1
Share

What Causes the Lack of Power When Accelerating from a Stop in a Mazda6?

Consider the following possible reasons: 1. Dead Battery: Most modern cars use maintenance-free batteries. Generally, green indicates normal battery charge, white indicates the need for charging or maintenance, and red means the battery is dead (some batteries use green for good condition, black for low charge, and white for battery damage requiring replacement). The typical lifespan of a battery is around two years. If the battery charge is found to be low, it should be replaced promptly. 2. Throttle Body Carbon Buildup: Carbon deposits in the throttle body or idle control valve can cause difficulty starting. For vehicles with an idle control valve, lightly pressing the accelerator while starting may help, but the engine may stall immediately after releasing the pedal. Therefore, it's best to have the throttle body cleaned and inspected at a repair shop. Additionally, during regular maintenance, ensure frequent replacement of the air filter. In northern regions with more dust, the air filter should be replaced every 10,000 km, or even sooner if driving on sandy or dusty roads. 3. Fuel Pressure: For proper engine startup, residual fuel pressure in the system after shutdown should not drop below 2.5–3.5 kg/cm². If pressure is too low, the fuel injectors won't deliver enough fuel for ignition. Repeatedly turning the ignition switch can temporarily restore fuel pressure, making startup easier. However, it's advisable to have a professional inspect the fuel system for faults. 4. Lubricant Quality: As winter approaches, it's essential to replace all lubricants, including engine oil, transmission fluid, and power steering fluid. Conventional lubricants thicken in cold weather, reducing flow and increasing friction, which makes cold starts difficult. Using slightly lower-viscosity oil can reduce mechanical wear and protect the engine.
10
5
Share

What Causes the Car Body to Shake When Accelerating?

There are several reasons why the car body shakes when accelerating: 1. Engine mechanical failure: such as uneven cylinder pressure in each cylinder. 2. Intake system failure: such as excessive dirt inside the intake pipe. 3. Engine management system failure: such as incorrect signals for coolant temperature or intake air temperature, or wiring faults. 4. Ignition system failure: such as excessive carbon buildup on spark plugs or incorrect gap, leakage in high-voltage wires or distributor cap, or damaged ignition coils. 5. Fuel supply system failure: such as injectors not sealing properly or clogging due to excessive carbon deposits inside the nozzle.
6
0
Share

What is the Huayra?

Huayra is a mid-engine supercar produced by Pagani. More details about the Huayra are as follows: 1. The Huayra is powered by a 6.0L twin-turbocharged V12 engine specially built by AMG for Pagani, with a maximum power output exceeding 700 horsepower and a peak torque of approximately 1000N·m. 2. The Huayra features gull-wing doors, a wedge-shaped front end, a teardrop-shaped glass cabin, alpaca-colored leather seats, and a full carbon fiber body. It integrates various multifunctional configurations such as an audio-visual system and a driving communication system, combining luxury with a strong sense of technology.
17
4
Share

How to Solve the Problem of Loud Engine Noise?

There are several solutions to the problem of loud engine noise: 1. Aging or loosening of engine mounts: Engine mounts are rubber blocks between the engine and the frame. Solution: Tighten or replace the engine mounts. 2. Improper use of engine oil: If the viscosity of the engine oil does not match the engine, it can easily cause carbon buildup, leading to increased engine noise. Solution: Use the engine oil grade specified in the vehicle manual and avoid mixing different brands of engine oil. 3. Engine misfire: An engine misfire means one or more cylinders are not functioning properly. Solution: Check the working condition of each ignition coil and cylinder spark plug.
5
1
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.