What is the Tesla Model C?

What Causes the Clicking Noise When Turning the Steering Wheel in the Buick Excelle?

The reasons for the clicking noise when turning the steering wheel in the Buick Excelle are: 1. Sound from the turn signal reset mechanism: If the turn signal is activated while turning, the noise might come from the reset clip of the automatic turn signal reset mechanism. The driver should verify this. If confirmed, it is a normal occurrence. Sometimes, multiple clicks may be heard because the steering column has three reset notches per full rotation. Turning the wheel one full circle may produce three clicks. 2. Noise from the steering column dust cover: If the noise comes from below the steering wheel, it might be due to the steering column dust cover. Lack of lubrication can cause friction sounds. Applying grease inside the dust cover should eliminate the noise. 3. Noise originating from the steering wheel: If the noise comes from within the steering wheel, it is likely caused by the clock spring (spiral cable) for the airbag. Removing the steering wheel and applying grease to the clock spring may help. If the noise persists, the clock spring may need replacement as it could be damaged. Be gentle when removing the steering wheel or disconnect the airbag fuse to prevent accidental deployment. 4. Noise from the strut mount bearing: If the noise comes from outside the car, it might be due to insufficient lubrication in the strut mount bearing. Open the hood and check if the noise originates from the top of the strut. If confirmed, applying grease to the bearing may help. If the noise continues, replacement is necessary. 5. Noise from the stabilizer bar: If the noise isn't from the strut, inspect the stabilizer bar bushings for looseness or damage. Loose or damaged bushings can cause noise when turning or driving on uneven roads. Loose bushings can be fixed with shims, but damaged ones must be replaced.

8

5

Share

What does the exclamation mark on Changan vehicles mean?

There are five possible scenarios when an exclamation mark appears on the car dashboard: general faults, automatic transmission faults, brake system faults, abnormal tire pressure, and lighting faults. Below is a detailed analysis of these five situations: General faults: A triangle with an exclamation mark inside indicates that the car's general performance or components and functions have malfunctioned. This mainly includes parking sensor failure, fuel cut-off system intervention or failure, external light failure, engine oil pressure sensor failure, etc. It is necessary to go to a 4S shop for inspection to identify the source of the fault. Automatic transmission faults: A yellow gear with an exclamation mark inside is the automatic transmission fault warning light, indicating that there is a fault in the transmission or the transmission lubricant is below the normal range. The transmission oil should be replaced in time. Brake system faults: An exclamation mark in the middle of a circle with parentheses represents a warning of the brake system, mainly including brake system failure and low brake fluid level. The brake system should be inspected immediately to avoid accidents. Abnormal tire pressure: An exclamation mark in the middle of a horizontal line under parentheses represents the tire pressure monitoring warning light. When the car's tire pressure is too low, this warning light will come on. It is necessary to check the car's tire pressure and restore it to the normal range. Lighting faults: A yellow bulb with an exclamation mark is the lighting fault indicator light, indicating that a car light has failed. Solution: Go to a 4S shop for inspection and treatment as soon as possible, or you can check it yourself, focusing on commonly used bulbs such as turn signals, fog lights, and interior lighting to see where the problem lies.

5

1

Share

Can I Make a U-Turn Before Entering the Highway?

Before entering the highway, you can make a U-turn if there is a U-turn sign; otherwise, it is not allowed. Scenarios where U-turns are permitted include: Presence of U-turn traffic lights or signs: When there is a U-turn traffic light at an intersection, you can make a U-turn when the U-turn light is green. If there is a U-turn sign or a U-turn marking on the lane, you can make a U-turn after ensuring the safety of yourself and others. No U-turn sign but left turns are allowed (no prohibition of U-turns): Vehicles can make a U-turn at intersections where left turns are permitted and there are no signs or markings prohibiting U-turns. It is important to note that vehicles should proceed according to the left-turn traffic signal without affecting the normal flow of other vehicles. If you need to make a U-turn at an intersection with a left-turn waiting area, you can first enter the left-turn waiting area when the straight-through light is green and wait until the left-turn light turns green before making the U-turn. U-turns are allowed at dashed lines: Whether it is a white or yellow dashed line, U-turns are permitted. For double yellow lines with one solid and one dashed, check if your side is the dashed line. If it is, you can make a U-turn safely; if it is solid, U-turns are not allowed.

18

1

Share

What are the precautions for driving through water?

Precautions for driving through water include assessing water depth, driving cautiously, and maintaining a safe distance from other vehicles. Specific precautions are as follows: Assessing water depth: Observe the water conditions to estimate the depth and determine if the vehicle's chassis will come into contact with the water. Compare the water depth with the vehicle's maximum wading depth to decide if it is safe to proceed. Then, maintain a steady throttle and drive at a constant speed in a low gear. Driving cautiously: Drive carefully when going through water. Avoid high speeds and maintain an appropriately slow speed, especially when turning, as hydroplaning can occur, leading to dangerous situations. Maintaining a safe distance from other vehicles: Keep a safe distance from the vehicle in front when driving through water. Due to the humid weather, the windshield is prone to fogging, and splashing water can also obstruct vision. Following too closely may result in a rear-end collision.

18

0

Share

What are the reasons for not being able to engage first gear?

1. Faulty positioning ball head: It may be that the positioning component of the gear lever's positioning ball head has failed, allowing the gear lever to rotate freely around its own axis and making it impossible to accurately control the gear position. Alternatively, the spherical working surface at the lower end of the gear lever may have worn off, preventing the gear lever from controlling the shift fork or the shift head's groove, making both gear engagement and disengagement impossible. 2. Clutch failure to disengage: It may be that the clutch cannot fully disengage, although the gearbox's shifting mechanism is functioning normally. This issue can be resolved by adjusting the clutch or replacing certain clutch components to achieve the appropriate free play and disengagement clearance. 3. Damaged shift fork: The shift fork may be loose, severely bent, deformed, or worn. In this case, the gear lever's movement reaches the correct position, but the shift fork's movement does not, resulting in severe impact and failure to engage the gear. The gearbox cover can be opened for inspection and repair, and the shift fork may need to be replaced if necessary.

5

3

Share

How Many Years Does a 6-Seater Vehicle Need to Undergo Annual Inspection?

A 6-seater vehicle requires its first on-site inspection in the 7th year. The scope of the 6-year exemption and the process for vehicle annual inspection are as follows: Scope of the 6-year exemption: According to the "Opinions on Strengthening and Improving Motor Vehicle Inspection Work" issued by the Ministry of Public Security and the General Administration of Quality Supervision, Inspection, and Quarantine, non-operational passenger cars and other small and micro passenger vehicles (excluding minivans and vehicles with 7 seats or more) within 6 years of initial registration are exempt from on-site inspection. This means that 6-seater vehicles can enjoy a 6-year exemption from on-site inspection. However, they still need to undergo periodic inspections every 2 years. Process for vehicle annual inspection: First, an exterior inspection is conducted to verify if the vehicle's appearance matches the details on the registration certificate. Next is the emission test to check if the exhaust meets standards, followed by chassis, brake, and lighting inspections. Finally, fees are paid at the counter, and the annual inspection sticker is issued after completing the necessary procedures.

4

3

Share

What is the Tesla Model C?

What Causes the Clicking Noise When Turning the Steering Wheel in the Buick Excelle?

What does the exclamation mark on Changan vehicles mean?

Can I Make a U-Turn Before Entering the Highway?

What are the precautions for driving through water?

What are the reasons for not being able to engage first gear?

How Many Years Does a 6-Seater Vehicle Need to Undergo Annual Inspection?

What documents are needed to deduct points at the DMV?

Can You Drive with Low Car Coolant Temperature?

How Long Does It Take to Repair a Damaged Car Front?

How Many More Years Can National IV Vehicles Be Driven?