What is the symbol for fog lights?

2 Answers
DiHope
09/03/25 6:04am
The symbol for fog lights is three diagonal lines with a vertical bar on the left. The details about fog lights are as follows: Automotive fog lights: They provide road illumination and safety warnings to other vehicles during rainy or foggy weather. The symbols for front and rear fog lights are quite similar, both featuring three lines with a vertical bar. Activating the rear fog light makes the vehicle more visible to other road users behind, as it is a red signal light installed at the rear of the vehicle with higher luminous intensity compared to the tail lights. Visibility range of fog lights: Approximately 100 meters. When visibility drops below 100 meters, fog lights should be turned on, and the vehicle speed should be reduced. The fog light switch is placed separately for easy access by the driver while driving.
Was this review help?
14
5
Share
KateFitz
09/15/25 7:33am
I've been driving for decades, and the fog light symbol is most commonly seen on the light control switch. That little icon looks like three downward-curving wavy lines, representing the front fog lights; or three horizontal curved lines, which indicate the rear fog lights. It's designed to be intuitive, with light penetrating thick fog without reflecting. When encountering severe weather like heavy fog or rainstorms, turning them on makes the road instantly much clearer. I remember last winter in the mountains, dense fog made it impossible to see anything, but the fog lights helped me safely navigate through the poor road conditions. The key is to use them appropriately—only turn them on when truly needed, otherwise, they can be too bright and interfere with other drivers' vision, and getting fined by the police is also a hassle. During regular maintenance, check the switch position to ensure the symbol is intact for peace of mind.
Was this review help?
18
1
Share
Expand All
More Forum Discussions

What does auxiliary lane mean?

Auxiliary lanes refer to the lanes on both sides of the main road that assist the main road traffic, while the main road lanes are the normal traffic lanes. The following is an introduction to the traffic rules of auxiliary and main roads: 1. Inverted triangle sign: When driving on the auxiliary road, you need to pay special attention to whether there is an inverted triangle sign on the auxiliary road. There will also be a red triangular sign on the side of the road with the word "yield" written in it, indicating that there are main road vehicles merging into the auxiliary road ahead, and you need to slow down. 2. Stop line and inverted triangle sign: There will be a stop line and an inverted triangle on the auxiliary road, which are yield signs. When you see red vehicles merging into the auxiliary road, yellow vehicles should slow down and yield before the stop line and must not cross the stop line, otherwise it may easily lead to a collision accident.
9
4
Share

What is the reason for the inexplicably high fuel consumption of the MG 6?

The reason for the inexplicably high fuel consumption of the MG 6 is that the actual comprehensive fuel consumption is related to multiple factors such as load, road conditions, driving habits, weather, wind speed, tire pressure, etc. The actual comprehensive fuel consumption should be based on the actual driving conditions. Factors affecting fuel consumption: There is a certain relationship between displacement and fuel consumption, but a higher fuel consumption does not necessarily mean a larger displacement. Relatively speaking, the size of a car's displacement does not directly correlate with its fuel consumption. In addition to displacement, factors such as the car's shape, weight, and engine technology are also important factors affecting fuel consumption. Solutions for high fuel consumption: Correct improper driving habits, maintain steady acceleration, avoid coasting in neutral, reduce the car's load, perform regular maintenance and inspections, and address any issues immediately when they are discovered.
19
4
Share

Where is the Geely Vision AC fuse located?

Geely Vision AC fuse is located under the dashboard (driver's side) and in the engine compartment (left side). Spare fuses and fuse clips are fixed inside the cabin fuse box cover. Steps to replace the fuse: Switch the power mode to ON, turn off the headlights and all accessories. Remove the fuse box cover. Use a cross screwdriver to remove the screws and replace with a new fuse. Check the small fuses in the engine compartment and inside the vehicle. If a fuse is blown, use a fuse puller to remove it and replace it with a new fuse. Precautions for replacing fuses: Replacing with a fuse of higher rated current will significantly increase the chance of damage to the electrical system. Replace with a spare fuse of the same rated current. Use the diagram to locate the problematic fuse and confirm the rated current on the fuse label.
12
1
Share

What Does Incorrect Use of Brake and Accelerator Pedals Mean?

Incorrect use of the accelerator pedal means failing to press the brake when deceleration is required or mistakenly pressing the accelerator instead, and failing to press the accelerator when acceleration is needed or mistakenly pressing the brake. Incorrect use of the brake and accelerator pedals results in an immediate deduction of 100 points, leading to a direct failure. Below is additional information: 1. Correct Procedure: Upon hearing the voice prompt "Please start," press the clutch, shift into first gear, activate the left turn signal (for more than 3 seconds), simultaneously (turn head left) check the left rearview mirror, confirm safety, honk the horn, release the parking brake, and start smoothly, then turn off the turn signal. On a slope, rolling backward during startup is prohibited. 2. Exam Failure: According to Article 44 of the "Regulations on the Application and Use of Motor Vehicle Driver's Licenses," each subject is tested once. If the test is failed, one retake is allowed. If the retake is not attended or is still failed, the current test is terminated, and the applicant must reschedule the test. However, the rescheduling for Subject 2 and Subject 3 must be done after ten days. If the Subject 3 safe driving knowledge test is failed, the passed road driving skill test scores remain valid.
20
1
Share

What is the solution for the brake caliper not returning to position?

Brake caliper not returning to position can be solved by thinning it with a steel file. Below are some relevant introductions about brakes: 1. Description: Brake pads are important components in a car's braking system, and they are also wear parts that need to be replaced regularly. 2. Function: When the driver presses the brake pedal, the vacuum booster provides assistance, helping the driver to press the brake pedal. After pressing the brake pedal, the master cylinder pushes the brake caliper through brake fluid, allowing the brake caliper to push the brake pads to clamp the brake disc. 3. Precautions: Brake pads, brake discs, and brake fluid need to be replaced regularly. Many car owners overlook the brake fluid during maintenance. Brake fluid is a liquid that easily absorbs water. If the water content in the brake fluid is too high, it can lead to reduced braking force and longer braking distances.
2
5
Share

What are the reasons for the loud fan noise in BMW e90 engine?

BMW e90 engine fan noise may be caused by the following reasons: Possible excessive bearing wear: Inspect the radiator and surrounding components to check for excessive bearing wear. If damaged, simply replace the bearing. Examine whether the cooling fan blades are rubbing against anything. If not, the fan is likely damaged, and replacing the fan bearing or coupler should resolve the issue. Poor fan cooling performance: This may be related to the fan belt or blade balance issues, or possibly due to a dirty radiator causing poor heat dissipation, which affects air intake volume. This leads to increased electronic fan speed and consequently louder wind noise. This problem does not affect daily usage. Clean the radiator and fan blades, and check for loose fan mounting screws. If the issue persists, directly replace the car's cooling fan.
2
2
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.