What is the symbol for coolant?

1 Answers
ColtonAnn
07/30/25 9:21am
The coolant symbol is highly recognizable. Below the coolant symbol are two wavy lines representing water, with a thermometer inserted between them. Modern vehicles use water-cooled engines, which rely on the continuous circulation of coolant to dissipate excess heat. Relevant information about antifreeze is as follows: 1. Introduction: The full name of antifreeze should be antifreeze coolant, meaning a coolant with antifreeze properties. Antifreeze prevents the coolant from freezing and expanding in cold winter conditions, which could otherwise crack the radiator or damage the engine cylinder block or cylinder head. 2. Function: It provides anti-corrosion protection for components of the cooling system; prevents scale formation, avoiding reduced radiator efficiency; ensures the engine operates within the normal temperature range.
Was this review help?
13
5
Share
More Forum Discussions

What does the fault code P150200 of GAC Trumpchi mean?

The fault code P150200 in the GAC Trumpchi GS4 indicates a malfunction of the vehicle's crankshaft position sensor. Replacing the crankshaft position sensor will resolve the issue. The function of the crankshaft position sensor is to determine the position of the crankshaft, specifically the crankshaft's angle and the engine's rotational speed. The crankshaft position sensor is typically installed at the front end of the crankshaft (near the pulley), the rear end near the flywheel, or the middle of the crankshaft. In older models, it may also be located inside the distributor. It is one of the most critical sensors in the control system. The functions of the crankshaft position sensor include: detecting the engine speed, hence it is also known as the speed sensor; detecting the top dead center position of the pistons, thus referred to as the top dead center sensor. This includes detecting the top dead center signals for each cylinder used in ignition control and the top dead center signal for the first cylinder used in sequential fuel injection control. Specific steps for replacing the crankshaft position sensor: Locate the crankshaft position sensor in the GAC Trumpchi GS4, use tools to loosen the fixing screws of the sensor, and manually unscrew them. Remove the old crankshaft position sensor from the vehicle. Install the new sensor in the GAC Trumpchi GS4 to complete the process.
10
1
Share

What type of engine oil is suitable for the Honda XR-V 1.5T?

Honda XR-V 1.5T uses engine oil with the specification 5W30 (4L), and the replacement interval is 5,000 kilometers. The Honda XR-V 1.5T is equipped with a 1.5T L4 engine, delivering a maximum power of 177 horsepower and a peak torque of 220 N·m. It is paired with a CVT transmission, achieving a top speed of 200 km/h. 5W30 oil, as a winter-grade oil, offers excellent lubrication due to its high viscosity and strong high-temperature resistance. Engine oil is often referred to as the lifeblood of the engine. Without it, the engine cannot operate. The oil specification carries specific meanings, and different specifications yield varying performance effects. The meaning of engine oil specifications: The "W" stands for winter. The smaller the number before the "W," the better the oil's low-temperature fluidity, indicating suitability for lower ambient temperatures and better engine protection during cold starts. The number after the "W" represents the oil's kinematic viscosity at 100°C. A higher number indicates higher viscosity, better high-temperature protection, and improved stability under high temperatures. Larger numbers are suitable for turbocharged engines, as turbochargers operate under high temperatures and speeds. In such cases, fully synthetic oil is essential, and a higher number after the "W" is preferable. The functions of engine oil: Engine oil not only lubricates but also cleans, seals, cushions, prevents rust, and dissipates heat. When the engine is running, the oil forms a protective film on the surfaces of engine components, preventing direct contact and friction. Direct friction between components would accelerate wear and generate excessive heat, causing severe damage to the engine. Over time, engine oil loses its performance, necessitating regular replacement. Prolonged use without replacement can accelerate engine wear. During each oil change, the oil filter should also be replaced. The oil filter ensures the cleanliness of the oil during use, which is crucial for proper engine lubrication. Considerations when selecting engine oil: Choose oil based on the engine's requirements. Avoid using overly advanced oil for engines with lower requirements or lower-grade oil for high-performance engines. Multi-grade oil is recommended due to its cost-effectiveness, longevity, and superior engine protection. Multi-grade oil may darken prematurely and exhibit lower oil pressure compared to conventional oils, which is normal. The type of engine oil may vary depending on the vehicle's usage cycle and condition. For specific recommendations, consult the staff at your local 4S dealership.
14
0
Share

How to Clean Car Windows Thoroughly?

Car windows can be cleaned thoroughly by following these steps: 1. First, wet the car windows with clean water, which helps remove dust from the surface. 2. Most portable car washers come with a small container specifically for cleaning solution. Fill this container with the cleaning fluid, spray it onto the car window surface using the washer’s nozzle, and wipe with a cloth. Then, rinse with high-pressure water. 3. After the windows are clean, evenly spray some anti-fog cleaning solution on them and wipe dry with a clean cloth. This method leaves a shiny film on the glass, preventing streaks, watermarks, and offering anti-fog and de-frosting effects.
10
3
Share

What are the methods for car maintenance?

Car maintenance methods include turning on the ignition before starting the vehicle and avoiding lugging the engine while driving. The car maintenance methods are as follows: Turn on the ignition before starting the vehicle: Turning on the ignition before starting the car helps maintain normal technical conditions, eliminates potential car issues, prevents accidents and faults, slows down the deterioration process, and extends the usage cycle. Avoid lugging the engine while driving: Lugging the engine while driving can easily cause tire damage, shorten tire lifespan, pose driving hazards, and also reduce the car's lifespan. Reducing lugging while driving helps extend the car's lifespan.
16
2
Share

Is it a pity to repaint the bumper over the original paint?

Repainting the bumper is for aesthetic purposes. Although it covers the original paint, it is not a pity. Here are the relevant details: 1. Repainting: Nowadays, car bumpers are made of plastic. In case of bumper damage, whether to repair it or repaint it is entirely up to personal choice, as it will not cause rust or corrosion issues to the vehicle itself. However, most drivers choose to repair it for aesthetic reasons. 2. Bumper: The car bumper is a safety device designed to absorb and mitigate external impacts, protecting the front and rear of the vehicle body. Many years ago, car bumpers were made of steel plates pressed into channel steel, riveted or welded to the frame longitudinal beams, with a significant gap from the body, which looked very unattractive.
10
0
Share

What is the difference between Sport Mode and S Gear?

There are two main differences between Sport Mode and S Gear: 1. Sport Mode is a combination of chassis and transmission programming: In high-end models abroad, Sport Mode includes heavier steering, stiffer suspension, and the transmission logic switching to S Gear. However, domestic vehicles lack dynamic chassis systems, so Sport Mode only involves heavier steering and the transmission logic switching to S Gear. 2. Simply engaging S Gear only involves changes in transmission logic, specifically not actively upshifting, not reaching the highest gear, shorter shift times, and reduced throttle lag, etc. Therefore, S Gear is only a part of Sport Mode.
17
5
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.