What is the suitable tire pressure for frequent highway driving?

Is it necessary to clean the air conditioning evaporator?

It is necessary to clean the air conditioning evaporator, otherwise bacteria will grow inside and a lot of dirt will accumulate. The functions of the car air conditioning are: 1. Drawing in fresh air from outside for ventilation and air exchange, preventing window fogging; 2. Removing dust, odors, smoke, and toxic gases from the air inside the car, making the air fresher, and humidifying the air inside the car to increase its relative humidity. The maintenance methods for car air conditioning are: 1. Do not set the temperature too low when using it; 2. Control the direction of the air outlet; 3. Do not use it for too long; 4. Appropriately turn on high air volume; 5. Turn off the air conditioning when driving at low speeds.

4

5

Share

Shift Gear First or Release Handbrake First?

Shift into gear first and then release the handbrake. This prevents the vehicle from rolling and avoids sudden acceleration due to operational errors, which could lead to traffic accidents. Therefore, when starting the vehicle, always check the handbrake's status first. If the handbrake has already been released prematurely, press the foot brake. The correct method for applying the handbrake is: 1. Press the handbrake button before pulling it; 2. Apply gentle force when pulling the handbrake; 3. Pull the handbrake up to about 70%—pulling it all the way to the top will shorten the lifespan of the handbrake cable. The dangers of forgetting to engage the handbrake while driving include: 1. The brake pump cannot provide sufficient braking force, causing the engine to stall; 2. Accelerated wear on the brake discs and hardening of the brake pads due to friction heat; 3. Stretching of the handbrake cable; 4. Leakage of brake cylinder fluid, leading to brake failure.

5

1

Share

Where is Changan Mazda cars produced?

Changan Mazda cars are produced at the Nanjing production base, while FAW Mazda's production base is located in Changchun. Taking the 2020 Changan Mazda 3 Axela as an example, it belongs to the compact car category with body dimensions of: length 4662mm, width 1797mm, height 1445mm, a wheelbase of 2726mm, and a fuel tank capacity of 50 liters. The 2020 Changan Mazda 3 Axela features a MacPherson strut front suspension and a torsion beam rear suspension. It is equipped with a 1.5L naturally aspirated engine, delivering a maximum horsepower of 117PS, maximum power of 86kW, maximum torque of 148Nm, and is paired with a 6-speed manual transmission.

20

0

Share

Does Leaving the Car in P Gear Without Turning Off the Engine Have Any Impact?

Leaving the car in P gear without turning off the engine does have an impact, including: Increased fuel consumption When the engine speed is very low, the intake vortex weakens, leading to poor fuel atomization, incomplete combustion, and increased leakage from valves and piston rings. The prolonged contact time between combustion gases and the cylinder walls increases heat loss, thereby raising fuel consumption. For gasoline engines, the weaker intake airflow at idle makes it harder for the carburetor to disperse fuel mist, requiring a richer air-fuel mixture, which may also increase fuel consumption. Increased component wear At idle, the engine oil pressure is relatively low, worsening lubrication conditions for moving parts. Unburned fuel washes the cylinder walls, and the weak intake vortex and incomplete combustion can easily lead to carbon deposits. When shifting gears, the following precautions should be noted: Looking down at the gear lever while shifting: Especially when driving in urban areas or at high speeds, looking down while shifting can cause the car to veer off course, potentially leading to accidents. Single-clutch shifting: Most modern cars are equipped with synchronizers, making gear shifts easier, but improper operation can be harmful. Using the double-clutch shifting method is beneficial for prolonging component lifespan. Downshifting without revving: When downshifting, gears with synchronizers can be shifted without revving and using a single clutch, but this can accelerate component wear and early failure. Therefore, whether the car has synchronizers or not, the double-clutch and revving method should be used for downshifting. Prolonged driving in low gear: Driving at low speeds for extended periods results in high engine RPM but low vehicle speed, reducing mileage per unit time and relatively increasing fuel consumption. After starting the car, unless it is a cold start, the gear should be shifted to an appropriate higher level as soon as possible. Generally, higher gears are more fuel-efficient than lower gears. Not fully depressing the clutch when shifting: If the clutch is not fully depressed, the engine and the transmission's input shaft cannot completely disengage, causing intermittent engagement during shifting, which can lead to gear grinding and damage. Veering off course while shifting: Many people shift gears with their right hand while pulling the steering wheel downward with their left hand, causing the car to drift toward the center of the road. This can lead to crossing lanes or occupying the wrong lane, which is very dangerous. Avoiding incomplete gear engagement: Forcing the gear lever into position when shifting can damage gears, not only harming components but also potentially causing accidents. Rocking the gear lever in neutral: After shifting to neutral, the gear lever often becomes unstable and may rock back and forth, accelerating component wear. Skipping gears when upshifting: Upshifting should be done sequentially, as skipping gears can cause discontinuous power delivery and stalling. Downshifting, however, can and should often be done by skipping gears. Shifting into reverse before the car stops: If the car is still moving forward when shifted into reverse, the gears can be damaged.

12

2

Share

Does the Captiva have a ladder frame chassis?

The Captiva does have a ladder frame chassis, as it belongs to the body-on-frame construction type. The Captiva is a mid-size SUV under the SAIC-GM Chevrolet brand. Taking the 2017 Captiva as an example, its body dimensions are: length 4690mm, width 1849mm, height 1753mm, with a wheelbase of 2707mm, a fuel tank capacity of 65 liters, and a curb weight of 1750kg. The 2017 Captiva features a MacPherson strut front suspension and a four-link independent rear suspension. It is equipped with a 2.4L naturally aspirated engine, delivering a maximum horsepower of 167PS, maximum power of 123kW, and maximum torque of 230Nm, paired with a 6-speed automatic transmission.

13

3

Share

How to Check the Wear Level of Teana Brake Pads?

To check the wear level of Teana brake pads: 1. Observe the raised indicators at both ends of the brake pads, which are 2 to 3 mm thick—this is the minimum replacement limit for the brake pads; 2. Listen for a sharp, screeching sound, which indicates that the thickness of the brake pads has fallen below the limit markers on both sides. Taking the 2021 Teana as an example, its body dimensions are: length 4901mm, width 1850mm, height 1450mm, with a wheelbase of 2825mm. The 2021 Teana is equipped with a 2.0L naturally aspirated engine, delivering a maximum power of 115kW and a maximum torque of 197Nm, paired with a CVT continuously variable transmission.

3

4

Share

What is the suitable tire pressure for frequent highway driving?

Is it necessary to clean the air conditioning evaporator?

Shift Gear First or Release Handbrake First?

Where is Changan Mazda cars produced?

Does Leaving the Car in P Gear Without Turning Off the Engine Have Any Impact?

Does the Captiva have a ladder frame chassis?

How to Check the Wear Level of Teana Brake Pads?

How to Turn Off the Auto Start-Stop Function in the Verano?

Where is the VIN number located on the Roewe RX5?

What does a bulb with an exclamation mark on the car dashboard mean?

How to Turn on the Heater in a Mercedes-Benz?