What is the structure of a gasoline engine?

1 Answers
RoseAnn
07/25/25 12:42am
Gasoline engines vary greatly depending on their application, manufacturer, and production era. However, they all consist of the engine block group, crankshaft and connecting rod mechanism, valve train, intake and exhaust systems, fuel system, cooling system, lubrication system, starting system, and harmful emission control devices. Introduction: A gasoline engine is an internal combustion engine that converts internal energy into kinetic energy using gasoline as fuel. Due to gasoline's low viscosity and rapid evaporation, a fuel injection system can spray gasoline into the cylinders. After compression reaches a certain temperature and pressure, a spark plug ignites the mixture, causing the gas to expand and perform work. Characteristics: Gasoline engines are characterized by high rotational speed, simple structure, light weight, low cost, smooth operation, and ease of maintenance and repair. They are widely used in automobiles, especially in small cars.
Was this review help?
5
0
Share
More Forum Discussions

How to Unclog the Sunroof Drain Holes of Baojun 730?

Use an air pump gun, aim it at the drain holes of the two front drainage pipes inside the sunroof, and blow through the pipes with high-pressure air. Remember to block with a rag. Flushing the drainage pipe with a syringe should be able to clear the pipe. Practical experience has proven this method to be very effective and simple to perform.
3
3
Share

How to Connect a BMW Mini Dash Cam to a Phone?

Insert the memory card into the side of the dash cam. Open the BMW-Advanced-Car-Eye app as indicated in the manual. Before launching the app, go to the WiFi settings on your phone and select the dash cam's WiFi network, then enter the password to connect. You can change the WiFi password, but be cautious as forgetting the new password may cause issues. It's recommended not to modify it unless necessary. Follow the on-screen instructions to proceed.
4
5
Share

How to Set Up the BMW Mirror Tilt Function?

You must adjust the mirror control to the R position. When shifting into reverse gear, the right-side mirror will tilt down to a certain angle. When the vehicle's forward speed reaches above 15 km/h, the mirror will automatically return to its original position. After removing the key, since the relevant settings have been saved, the mirrors will automatically return to their positions.
13
5
Share

How to Remove the Rear Seats of an Audi A8?

First, pull the strap located in the middle of the rear seat of the SAIC-GM Buick Regal to lift the rear seat cushion. There are four clips securing the rear seat underneath. After lifting the rear seat cushion, you need to remove the four fixing clips on both sides one by one. Once the seat is removed, there is a release handle for the rear seat backrest near the door. Pull the handle to fold down the backrest, then remove the backrest.
20
0
Share

How to Deal with Fogging on a BMW Car?

In winter, using the warm air to raise the temperature of the front windshield can reduce the temperature difference between the inner and outer surfaces of the glass, thereby preventing excessive fogging on the front windshield in time. Utilizing the air conditioning's dehumidification function to lower air humidity is another method to remove fog. Of course, remember to press the front windshield defogging button. Spraying defogger on the windows is also an effective method. Spray the defogger on the inner side of the front windshield and windows, then wipe evenly with a cloth and let it dry in the sun.
18
0
Share

How to reset the brake pad warning on BMW X1?

Before resetting, ensure that the brake pads or brake fluid and the sensor wire have been replaced. After meeting the above conditions, turn off the vehicle and the ignition switch, then turn the ignition switch back on. There is a small button at the lower left corner of the speedometer; press and hold it to display the maintenance information. Press once to switch between different maintenance items. After switching to the rear brake pads, press and hold again. When prompted to reset, press and hold once more to complete the process.
14
0
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.