What is the standard size of reflective stickers?

1 Answers
SanZoey
07/29/25 4:06pm
3M vehicle reflective stickers generally come in the size of: 5cmX45.72m, 5cm in width and approximately 45.72 meters in length. Relevant regulations: Domestic regulations only require trucks to have reflective strips to enhance safety during nighttime driving. There are no explicit regulations for private cars, so it's optional. However, if applied, they must be installed according to the requirements; otherwise, penalties may be imposed by traffic police if discovered. Requirements for applying reflective film: The visible light transmittance of the front windshield in the driver's viewing area and the areas used for observing external rearview mirrors while driving should be greater than or equal to 70%. No mirrored reflective sunshade film should be applied to any window glass.
Was this review help?
7
4
Share
More Forum Discussions

What are the reasons for a car not starting at all?

The reasons for a car not starting are as follows: 1. Dead battery: This could be due to a drained battery from leaving the headlights on for a long time or the battery reaching the end of its lifespan. It is generally recommended to replace the battery every 2 years. Additionally, installing xenon headlights, high-power audio systems, or DVD players can also cause electrical circuit failures in the vehicle. Checking for a dead battery is simple—just press the horn to find out. 2. Incorrect gear position: For automatic transmission vehicles, the gear must be in P (Park) or N (Neutral) to start the car. Placing it in R (Reverse) or D (Drive) will prevent the car from starting and may pose safety risks. Most modern cars have gear position reminders, so this issue is less likely to occur. 3. Out of fuel: If the car doesn't start, check the fuel gauge first to see if the tank is empty. Avoid waiting until the fuel gauge is completely empty to refuel, as this can also harm the engine.
12
4
Share

What is the fuel consumption of the Geely Emgrand GL?

The official combined fuel consumption of the Geely Emgrand GL is 5.9L/100km. Relevant information about car fuel consumption is as follows: Constant-speed fuel consumption: refers to the fuel economy indicator when a car is driving at a constant speed on a good road surface. Since constant-speed driving is a basic operating condition for cars on highways, and this type of fuel consumption is easy to measure, it is widely adopted. For example, France and Germany use the constant-speed fuel consumption at 90Km/h and 120Km/h as the main evaluation indicators for fuel economy. Road cycle fuel consumption: is the fuel economy indicator measured when a car drives in repeated cycles according to specified speeds and time norms on the road, also known as multi-condition road cycle fuel consumption. In the speed and time norms, each cycle includes various driving conditions, and specifies the gear shifting moments, braking and stopping times, as well as the values of driving speed, acceleration, and braking deceleration for each cycle.
9
4
Share

What does Subject 2 test?

Subject 2 test items include reverse parking, parallel parking, hill start and stop, right-angle turn, and curve driving. The following is a detailed introduction to the preparation before the Subject 2 test: 1. Preparation before the test: (1) Get the check-in number: Bring your ID card and admission ticket. After the driving school organizes you to arrive at the test site, arrive at the waiting hall 30 minutes in advance according to the scheduled test session to swipe your ID card and get the check-in number. (2) Wait for the call: Wait in the test hall. Please pay attention to the broadcast in the hall and the information displayed on the screen. After your name is called, go to the corresponding test lane to wait according to the instructions. 2. Preparation before getting in the car: Fasten your seat belt, first adjust the seat to the position you usually practice driving, then adjust the rearview mirror for easy viewing; after confirming with the examiner to start the test, you can start the test according to the voice prompts.
1
0
Share

What is the solution for the P0016 trouble code?

First, check whether the timing belt is broken or has skipped teeth. Then, inspect the solenoid valve that adjusts the valve timing for any damage, and verify that the oil pressure is normal. Finally, realign the timing. Below is more information about the P0016 trouble code: 1. The P0016 trouble code applies to all automobile manufacturers and indicates a crankshaft position/camshaft position correlation (Bank 1, Sensor A) issue. 2. The crankshaft converts the up-and-down motion of the pistons into rotational motion. The camshaft controls the opening and closing of the valves. The electronic control unit continuously monitors the variable camshaft's timing position to check the relative position between the camshaft and the crankshaft. If the misalignment exceeds one tooth, this trouble code will appear. Possible causes include a faulty camshaft position sensor or its circuit, a faulty crankshaft position sensor or its circuit, a faulty engine speed sensor, contaminated engine oil, or a stuck variable camshaft solenoid valve.
17
0
Share

What are the C-IASI Peugeot 5008 crash test results?

C-IASI Peugeot 5008 crash test results show that its safety rating has achieved five stars. Relevant information about C-IASI crash tests is as follows: C-IASI crash test: It is China's most authoritative automotive crash test, similar to the U.S. IIHS, which is recognized as the world's most authoritative automotive crash testing organization. Main tests include: the vehicle's driver-side impact, side impact, roof strength, seat headrests, pedestrian protection, auxiliary safety, and repair costs, among others. Relevant information about the Peugeot 5008 is as follows: Peugeot 5008: It is another compact MPV following the 3008, featuring a seven-seat or five-seat layout, with a length of 4.53 meters and a height of 1.64 meters. Powertrain: Peugeot offers the new 5008 with two 1.6L VTi turbocharged gasoline engines and two 1.6L and two 2.0L HDi diesel engines. The two VTi gasoline engines produce 120bhp and 156bhp, with fuel consumption of 7.3L/100km and 7.1L/100km, respectively.
13
4
Share

What is the fuel consumption of the Hyundai Mistra?

The fuel consumption of the Hyundai Mistra is as follows: 1. The 1.6T model has a fuel consumption of 8.0 liters per 100 kilometers. 2. The manual transmission 1.8L model has a fuel consumption of 7.9 liters per 100 kilometers. 3. The automatic transmission 1.8L model has a fuel consumption of 8.4 liters per 100 kilometers. Related details are as follows: 1. 1.6L engine: The Mistra's 1.6L turbocharged engine delivers 175 horsepower and a maximum torque of 265 Nm. This engine can output maximum power at 5500 rpm and maximum torque between 1500 to 4500 rpm. It is paired with a 7-speed dual-clutch transmission. 2. 1.8L engine: The Mistra's 1.8L naturally aspirated engine produces 143 horsepower and a maximum torque of 176 Nm. This engine can output maximum power at 6200 rpm and maximum torque at 4500 rpm. It is matched with either a 6-speed manual transmission or a 6-speed automatic transmission.
13
5
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.