What is the speed limit for domestic locomotives?

1 Answers
DeLyla
07/29/25 10:05pm
Domestic locomotives must not travel below 60 kilometers per hour, and the maximum speed must not exceed 80 kilometers per hour. Legal provisions: According to Article 45 of the "Regulations for the Implementation of the Road Traffic Safety Law of the People's Republic of China," motor vehicles driving on the road must not exceed the speed indicated by speed limit signs or markings. On roads without speed limit signs or markings, motor vehicles must not exceed the following maximum speeds: roads without a centerline, urban roads at 30 kilometers per hour, highways at 40 kilometers per hour; roads with only one motor vehicle lane in the same direction, urban roads at 50 kilometers per hour, highways at 70 kilometers per hour. Reasons for speed limits: They are established based on ensuring driving safety while making full use of road resources. Reducing the possibility of longitudinal collisions. Speeding vehicles often follow other vehicles closely, and when the leading vehicle applies emergency braking, the following vehicle is prone to rear-end collisions due to insufficient distance. Reducing the possibility of rollovers. Excessive speed increases centrifugal force when turning, making the vehicle more likely to roll over.
Was this review help?
12
4
Share
More Forum Discussions

What is the ground clearance of a sports car?

The ground clearance of supercars is never less than 7cm. The LP640 has a minimum ground clearance of 14cm, which reduces to around 10cm when fully loaded. The standard ground clearance for an F1 car is 8cm, and when fully loaded (full fuel + driver), it can be as low as 5-7cm, depending on the specific model and suspension stiffness. Vehicles driven on public roads cannot go below these standards. The chassis serves to support and mount the car's engine and its various components and assemblies, forming the overall shape of the vehicle. It also receives power from the engine to enable motion and ensure normal operation. Additionally, a well-designed chassis can safeguard the driver's life.
17
4
Share

What is the normal tire pressure for a Geely Boyue?

The normal tire pressure for a Geely Boyue is between 2.4-2.5 bar. Due to seasonal factors, the tire pressure can be appropriately increased by 0.2 bar in winter and decreased by 0.1 bar in summer. The tire pressure monitoring system in the Geely Boyue can be viewed on the dashboard, specifically under the special function prompts (tire pressure monitoring, active safety information, including distance alerts, ACC cruise mode, lane departure warning, collision warning, PEPS, etc.). The tire pressure monitoring reset method for the Boyue is relatively simple; just driving for a while will restore it to normal data without any additional settings. If the tire pressure monitoring indicator light comes on (a yellow symbol with an irregular circle, no stamp on top, four small spikes at the bottom, and an exclamation mark inside), there are generally three possible reasons: Abnormal tire pressure. Typically, the system will alert if the pressure is below 1.8 bar or above 3.0 bar. In this case, the tires need to be checked and the pressure adjusted. Tire pressure monitoring not reset. After inflating the tires, if the tire pressure reset is not performed promptly, the system will still record the previous data, causing the tire pressure monitoring light to stay on. Simply performing a tire pressure reset will resolve this issue. Damaged tire pressure sensor. The tire pressure sensor, which monitors tire pressure, is installed inside the tire and connected to the tire inflation valve. If the sensor is damaged during driving (e.g., by hitting a curb), it can trigger the tire pressure warning light. In case of sensor damage, the only solution is to replace it with a new part.
18
1
Share

What are the reasons for the SITRAK turn signal not working?

Open circuit, flasher relay failure, excessive contact gap. The following is the relevant content: 1. Turn signal: The turn signal is an important indicator light that is turned on when a motor vehicle turns to alert vehicles and pedestrians in front, behind, left, and right. The turn signal bulb uses a xenon bulb, controlled by a single-chip microcomputer circuit, working continuously with alternating left and right flashes. The turn signal uses a flasher to achieve light blinking. It can be mainly divided into three types: resistance wire type, capacitor type, and electronic type. 2. Introduction to SINOTRUK SITRAK: SINOTRUK SITRAK was established in 1958 and is a provincial key state-owned sole proprietorship enterprise.
6
4
Share

Why Does the Car Stall During Driving Practice?

During the learning process, stalling is mostly caused by poor coordination between the throttle and clutch. Here are some precautions for beginners: 1. Don't forget to engage the handbrake when parking: Failing to do so may lead to the risk of the car rolling, which can not only damage your own vehicle but also potentially harm others' property or even lives. 2. Don't forget to release the handbrake when starting: When first learning to drive, always follow the correct sequence when starting the car. Regardless of whether the handbrake was engaged when parking, always check and release it before starting. 3. Don't forget to shift to neutral when exiting the car: Forgetting to shift back to neutral or P after parking can easily cause the car to stall.
12
4
Share

How to Distinguish Between Good and Bad Car Air Filters?

Here are the methods to distinguish between good and bad air filters: 1. Water test - this is the most crucial and simplest method, especially for those without experience. Water is the best way to test the quality of an air filter. Place the air filter flat on the ground or a table and sprinkle some water on the filter paper: (1) If the water seeps into the filter paper within 5 minutes, it is made of cotton pulp paper and must not be used. (2) If the water seeps in within 2-5 hours, the filter is made of low-grade wood pulp paper. It can be used but will affect the air compressor's efficiency (higher electricity consumption, less air output). Due to their relatively lower price, such filters are commonly used in the air compressor industry despite their drawbacks. (3) If the water takes 12-15 hours to seep in, it is a mid-grade filter paper. Typically, better-quality domestic machine manufacturers use such filters as original equipment consumables. (4) If the water does not seep in even after 24 hours, it is definitely a high-grade filter paper, usually chosen by high-end machine manufacturers as original equipment consumables. 2. Check the filter paper's uniformity, light transmittance, and surface smoothness by holding it up to a light source. Uniform and fine texture, good light transmittance, and smooth surface indicate high filtration precision and good air permeability. 3. Examine the depth and number of pleats in the filter paper. A deeper and more pleated filter paper indicates a larger filtration area, which generally results in better air permeability.
15
5
Share

What Do the Numbers on Car Windows Represent?

The 17-digit number on a car's windshield is the vehicle identification number (VIN). Below is a detailed introduction to the VIN: Purpose of the VIN: The VIN, also known as the vehicle identification number, is a unique 17-character alphanumeric code that serves as the car's identity card. Each vehicle has its own unique VIN, where the letters and numbers represent information such as the vehicle's production region, manufacturer, production year, model, and more. Location of the VIN: The VIN is typically located on the driver's side of the windshield, some can be found on the front partition of the engine compartment, and others may be on the vehicle's central pillar or the vehicle's nameplate.
14
3
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.