What is the spark plug model for the Baojun 630?

1 Answers
HavenLynn
07/29/25 11:01pm
The NGK DCP7REGP is the spark plug model for the Baojun 680. Main types of spark plugs include: standard spark plugs, extended insulator spark plugs, electrode spark plugs, seat-type spark plugs, pole-type spark plugs, and surface gap spark plugs. Spark plug replacement cycle: Under normal maintenance conditions, replacement is recommended after driving 40,000 to 60,000 kilometers. However, this may vary depending on the brand and engine, so it is advisable to follow the user manual. You can refer to the following standards for maintenance replacement: platinum spark plugs should be replaced at 40,000 kilometers, ordinary nickel alloy spark plugs at 20,000 kilometers, and iridium spark plugs at 60,000 to 80,000 kilometers. How spark plugs work: Under high voltage, the air between the center electrode and the side electrode of the spark plug rapidly ionizes, forming positively charged ions and negatively charged free electrons. When the voltage between the electrodes reaches a certain level, the number of ions and electrons in the gas increases like an avalanche, causing the air to lose its insulating properties and forming a discharge channel, resulting in a "breakdown" phenomenon. At this point, the gas forms a luminous body, known as a "spark." Along with the heat expansion, a "crackling" sound is also produced. The temperature of this electric spark can reach as high as 2,000-3,000°C, which is sufficient to ignite the air-fuel mixture in the engine's combustion chamber.
Was this review help?
19
3
Share
More Forum Discussions

What Type of Oil is Best for the Buick Excelle?

The original oil for the Buick Excelle 1.4T is Mobil 1 5W-30 fully synthetic oil, while the Buick Excelle 1.5L uses the factory-recommended 5W-30 semi-synthetic oil, with a refill volume of approximately 3.7L. For later maintenance and oil changes, you can choose from brands such as Shell or Castrol. The viscosity of oil changes with temperature, so it's important to pay attention to its performance under both low and high temperatures. For example, in 5W-30, the first number indicates low-temperature fluidity. 5W means it can withstand temperatures as low as -30°C. The smaller this number, the better the low-temperature fluidity, ensuring smoother cold starts for the car. The second number represents the oil's kinematic viscosity at 100°C. A higher number means the oil can maintain its viscosity better at high temperatures, which can be understood as better lubrication performance under high-temperature conditions. The method for changing the oil in a Buick Excelle is as follows: Wait for the engine temperature to cool down, allowing the oil to flow back into the oil pan. Use a wrench to loosen the oil drain plug and place an oil pan underneath to catch the old oil until it stops flowing. Start the engine and let it run for 30 seconds to allow the oil in the main oil passage to drain out. Use a specialized wrench to remove the oil filter. Apply oil to the oil seal of the new oil filter and tighten it clockwise by hand. Add the new oil through the oil filler cap on the engine valve cover. Typically, fill about three-quarters of a standard oil container. Start the engine and let it run for 5 minutes, checking for any leaks around the oil drain plug and oil filter. If leaks are found, perform necessary repairs. After stopping the engine, pull out the oil dipstick to ensure the oil level is within the standard range.
5
0
Share

How to Reset the Maintenance Light on Changan Alsvin?

To reset the maintenance light on the Changan Alsvin: 1. On the trip mileage display interface, press the right-hand stalk for more than 5 seconds until "oil" appears in the lower right area of the display; 2. Quickly press the right-hand stalk 5 times within 2 seconds; 3. The "oil" indicator will blink 3 times and then turn off, indicating the reset is complete. The Changan Alsvin is a compact 4-door, 5-seater sedan with body dimensions of 4545mm in length, 1730mm in width, 1475mm in height, and a wheelbase of 2650mm. It is equipped with a 1.6L naturally aspirated engine and a 6-speed automatic transmission, delivering a maximum power of 90 kW and a maximum torque of 158 Nm.
14
2
Share

How to Reset the Maintenance Light on a Volkswagen?

Volkswagen maintenance light reset method is: 1. Insert the key and wait; 2. Press and hold the set button on the instrument panel; 3. Turn on the power switch (do not start the engine), wait for 10-15 seconds; 4. Press and hold the button to the left of the set key, then start the engine to complete the reset. Volkswagen models include: Lavida, Magotan, Sagitar, Golf, Bora, etc. Taking Lavida as an example, it belongs to the compact car category with body dimensions of: length 4670mm, width 1806mm, height 1474mm, wheelbase 2688mm, fuel tank capacity 51L, and trunk capacity 510L.
19
0
Share

What is the function of the exhaust gas valve?

Automobile exhaust gas valve is used to allow the exhaust gas to re-enter the cylinder for combustion again. The following is the relevant information about the automobile exhaust gas valve: 1. The automobile exhaust gas valve, also known as the oil-gas separator or oil-water separator, is designed to handle the gases that escape from the combustion chamber into the crankcase during ignition. As these gases accumulate, they need to be managed to prevent excessive pressure and avoid releasing them into the atmosphere, which would cause pollution. Therefore, these gases are redirected back into the intake system for reuse. In some vehicles, the intake port is located before the throttle valve, while in others, it is situated on the intake manifold after the throttle valve. 2. A small portion of the exhaust gas helps to lower the temperature inside the cylinder during combustion. Since NOX is generated under high-temperature and oxygen-rich conditions, this process inhibits the formation of NOX, thereby reducing its content in the exhaust gas. The engine control unit (ECU) regulates the opening of the electromagnetic valve based on factors such as engine speed, load (throttle opening), temperature, intake airflow, and exhaust temperature. The vacuum from the intake pipe passes through the electromagnetic valve into the vacuum chamber of the EGR valve, causing the membrane rod to open the EGR valve. A small portion of the exhaust gas then enters the intake system through the EGR valve, mixes with the air-fuel mixture, and enters the cylinder for combustion. 3. When the engine is idling, running at low speed, under light load, or during cold starts, the ECU prevents exhaust gas from participating in the recirculation to avoid affecting engine performance. However, when the engine exceeds a certain speed, load, or reaches a specific temperature, the ECU allows a small portion of the exhaust gas to participate in recirculation. The amount of exhaust gas involved in recirculation varies depending on the engine speed, load, temperature, and exhaust gas temperature to minimize the NOX content in the exhaust gas.
8
3
Share

How to Reset the Tire Pressure Light on an Audi A3?

Audi A3 tire pressure light reset steps: First, enter the main menu and locate the tire pressure monitoring system. Then, reset the tire pressure data. Once the data is successfully set, save it, and finally exit the system and turn off the vehicle to complete the process. Tire pressure monitoring light on: The tire pressure monitoring indicator is a yellow symbol—an irregular circle with no stamp on top and four small spikes at the bottom, containing an exclamation mark inside. The tire pressure monitoring light indicates abnormal tire pressure. Abnormal tire pressure is generally caused by one of the following three reasons: Abnormal tire pressure: Typically, an alert is triggered if the pressure is below 1.8 bar or above 3.0 bar. In this case, inspect the tires and adjust the pressure. Tire pressure monitoring not reset: After inflating the tires, if the tire pressure is not reset promptly, the system will still record the previous data, causing the tire pressure monitoring light to illuminate. Simply perform a tire pressure reset to resolve this. Damaged tire pressure sensor: The tire pressure sensor, installed inside the tire and connected to the inflation valve, monitors tire pressure. If the sensor is damaged due to impact while driving, the tire pressure warning light will turn on. For sensor damage issues, the only solution is to replace it with a new component.
14
2
Share

What is the difference between AT transmission and AMT transmission?

The differences between AT transmission and AMT transmission are: 1. Different forms of transmission: AT transmission represents automatic transmission; AMT transmission represents automated manual transmission. 2. Different functions: AT transmission does not require the use of a clutch for shifting; AMT transmission achieves shifting through an added microcomputer control system that automatically operates the mechanism. Both AT transmission and AMT transmission belong to automatic transmissions, which are gear-shifting devices that can automatically shift gears based on the vehicle's speed and engine RPM, as opposed to manual transmissions.
2
3
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.