What is the solution when the one-key start of Trumpchi GS8 does not respond?

1 Answers
AnastasiaAnn
07/24/25 7:18am
Instructions for using the one-key start of Trumpchi GS8: Carry the smart remote key with you and enter the vehicle. Press the brake pedal all the way down and keep it in that position, ensuring the start switch indicator light is green. Shift the gear lever to the "P" or "N" position. Press the start switch to start the engine. Additional information: After the engine starts successfully, release the start switch immediately. The engine start time should not exceed 10 seconds. If the engine fails to start successfully, wait about 30 seconds before trying again. After starting, do not press the accelerator pedal sharply to make the engine run at high speed or overload. Otherwise, it is very easy to damage the engine.
Was this review help?
18
1
Share
More Forum Discussions

What is the tire size of the Audi A4?

Audi A4's tire specifications vary depending on the configuration: 1. The base model's tire size is 225/55r16; 2. The premium model's tire size is 225/50r17. More information about the Audi A4 is as follows: 1. The body dimensions of the Audi A4 are: length 4587mm, width 1772mm, height 1427mm, with a wheelbase of 2642mm, a fuel tank capacity of 70 liters, and a trunk capacity of 460 liters. 2. The Audi A4 is equipped with a 2.0T turbocharged engine, with a maximum power of 147kW and a maximum torque of 280Nm, paired with a continuously variable transmission. It features a four-link independent front suspension and a trapezoidal guide arm-type rear independent suspension.
15
4
Share

What is the solution for diesel vehicle DPF regeneration failure?

Diesel vehicle DPF regeneration failure has two solutions: one is regeneration, and the other is direct replacement. Causes of DPF regeneration failure: Excessive particulate matter adsorbed by DPF, high signal voltage feedback from differential pressure sensor to ECU, circuit issues, DPF blockage, differential pressure sensor failure, ECU malfunction. Reasons for frequent DPF regeneration: Use of low-quality gasoline containing excessive impurities and carbon compounds that easily clog the DPF, failure to use low-ash engine oil (which contains fewer impurities and reduces DPF clogging probability), and prolonged low-speed driving which decreases fuel combustion efficiency.
2
3
Share

What are the symptoms of a dirty motorcycle carburetor?

Reduces the engine's service life. Unstable idling, prone to stalling in neutral gear. Low-speed operation may cause "cylinder misfire" phenomenon. The exhaust pipe tends to emit black smoke. Here is relevant information: 1. Cylinder: There are 2-stroke and 4-stroke cylinders, with 2-stroke cylinders commonly used in machines like motorcycles, chainsaws, and lawn mowers. 2. Precautions: Before departure, always ensure the motorcycle's fluid levels are correct. Typically, the status of engine oil and coolant can be easily checked by viewing the instrument panel indicators, while brake and clutch fluid levels require observation from specific positions. Special attention should be paid to the coolant level in the radiator during summer.
1
1
Share

How Much is 5 Newton Meters of Torque?

This is related to the magnitude of torque and there is no separate conversion formula. Below is relevant information about automotive torque: 1. Definition: Automotive torque is the moment of force output from the crankshaft end of the engine. Under fixed power conditions, it has an inverse relationship with engine speed—the faster the speed, the smaller the torque, and vice versa. It reflects the vehicle's load capacity within a certain range. The reciprocating motion of the piston in the cylinder does a certain amount of work per cycle, measured in Newton meters. The work done per unit distance is torque; 2. Calculation: Torque × transmission gear ratio × final drive ratio × mechanical efficiency.
8
1
Share

How to Use the Warning Triangle?

According to the 'Road Traffic Safety Law of the People's Republic of China', on regular roads, when a vehicle breaks down or is involved in a traffic accident, the warning triangle should be placed 50 to 100 meters behind the vehicle. Below are the standards for placing the warning triangle: Highways: On highways, the warning sign should be placed at least 150 meters behind the vehicle. In case of rain or fog, the distance should be increased to 200 meters. Urban Roads: On urban roads, the warning triangle should be placed 50 meters behind the vehicle. At night, the distance should be extended to 150 meters.
11
5
Share

What are the reasons for a sudden increase in fuel consumption in diesel vehicles?

Diesel vehicles may experience a sudden increase in fuel consumption due to the following reasons: 1. Maintenance issues: Excessive or insufficient engine oil, poor quality, high viscosity, or failure to change it on time are all critical factors affecting engine operation; a dirty air filter can block the intake, increasing intake resistance, reducing power, and increasing fuel consumption. 2. Oxygen sensor failure: The oxygen sensor, located in the vehicle's exhaust pipe, is a ceramic component that detects and controls the oxygen-to-fuel ratio. It monitors exhaust gases to regulate the fuel injection system. If the oxygen sensor fails, it can affect the fuel supply, leading to a significant direct increase in fuel consumption.
13
5
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.