What is the solution for diesel vehicle DPF regeneration failure?

1 Answers
VanJosiah
07/30/25 9:36am
Diesel vehicle DPF regeneration failure has two solutions: one is regeneration, and the other is direct replacement. Causes of DPF regeneration failure: Excessive particulate matter adsorbed by DPF, high signal voltage feedback from differential pressure sensor to ECU, circuit issues, DPF blockage, differential pressure sensor failure, ECU malfunction. Reasons for frequent DPF regeneration: Use of low-quality gasoline containing excessive impurities and carbon compounds that easily clog the DPF, failure to use low-ash engine oil (which contains fewer impurities and reduces DPF clogging probability), and prolonged low-speed driving which decreases fuel combustion efficiency.
Was this review help?
2
3
Share
More Forum Discussions

What phenomenon does the movement of the steering wheel belong to?

The movement of a car's steering wheel involves both translation and rotation. Detailed analysis: When driving straight, the car's steering wheel undergoes translation. When turning the steering wheel, it rotates—meaning it rotates when being turned and translates when not being turned. Introduction to the steering wheel: A wheel-shaped device used to control the direction of vehicles such as cars, ships, and airplanes. The earliest cars used a tiller for steering control. Function of the steering wheel: The steering wheel is typically connected to the steering shaft via splines. Its function is to convert the force applied by the driver to the edge of the steering wheel into torque, which is then transmitted to the steering shaft. The steering intermediate shaft, as a connecting component between the steering gear and the steering shaft, facilitates the standardization of the steering gear, compensates for errors during manufacturing and installation, and optimizes the placement of the steering gear and steering wheel in the vehicle.
8
1
Share

What Causes the Strange Noise and Failure to Start When Igniting the Car?

The reason for the strange noise and failure to start when igniting the car is insufficient battery power or low voltage. Specific details are as follows: Insufficient Power: Forgetting to turn off the headlights or some electrical equipment before turning off the car may drain the battery, leading to insufficient power and causing the car to fail to start. Battery Usage Duration: If the battery has been used for too long and is severely aged, the voltage may be insufficient, requiring replacement. Car Battery: A car battery, also known as a storage battery, is a type of battery that works by converting chemical energy into electrical energy. Typically, the battery refers to a lead-acid battery, which is mainly made of lead and its oxides, with a sulfuric acid solution as the electrolyte.
6
2
Share

What are the reasons for a car's 12V socket not having power?

The reason for a car's 12V power socket not having power is a blown fuse in the power supply. Below is an introduction to the relevant content: 1. Replacement: If a car fuse is blown, the faulty fuse needs to be replaced. Besides going to a repair shop for replacement, you can also replace the fuse yourself. Locate the fuse position based on the specific car model. Generally, the fuse box is near the battery. The fuse box is usually secured with clips. 2. Current: When the current exceeds a certain limit for a period, the fuse will blow. If you replace it with a wire that is not easy to melt, it will fail to prevent hazards normally, with the worst-case scenario being spontaneous combustion. Car fuses are inexpensive and easy to replace, and you can store spare fuses in the car's fuse tray.
9
1
Share

Can You Release the Clutch After Starting on a Slope?

When starting on an uphill slope, you cannot fully release the clutch. Specific precautions are as follows: Driving Posture: Maintain the correct driving posture, pay attention to various traffic conditions on the road ahead, and do not look down. Clutch Pedal: Do not immediately release the clutch pedal; instead, first apply the throttle and then release the clutch. This is because the resistance of the car on an uphill slope is greater, requiring more power to start. Braking Timing: The key point is to master the timing of releasing the handbrake. If released too early, the vehicle may roll backward; if released too late, it may cause the engine to stall. The optimal timing is when the clutch pedal is lifted to the semi-engaged position and the engine sound changes, then release immediately.
16
2
Share

What Kind of Wax is Good for Car Polishing?

Different types of wax should be used for cars under varying climate conditions. Here is an introduction to car waxing: 1. For newly painted cars or those with dull body gloss, polishing wax can be used to maintain the body's shine and color; 2. In seasons and regions with heavy rainfall, waterproof wax is recommended; during summer when sunlight is intense, wax with strong resistance to high temperatures and UV rays should be chosen to prevent paint discoloration; 3. For cars operating in harsh environments, silicone resin wax with stronger protective properties is advisable; 4. High-end cars with superior paint quality can opt for premium imported wax; 5. For ordinary cars, dark-colored paint should use black, red, or green series wax, while light-colored paint should use silver, white, or pearl series wax; 6. It is not recommended to wax new cars as they come with original wax, to avoid wastage.
4
2
Share

How to Reset the Tire Pressure Monitoring Indicator After a Pressure Check?

Tire pressure monitoring alerts can be cleared by resetting the tire pressure monitoring system and restarting it. Below are the reasons why the dashboard displays the tire pressure monitoring indicator after a pressure check and needs a restart: 1. It indicates that one of the four tires has insufficient pressure, likely due to a puncture or air leak. It's best to visit a tire repair shop to check if the tire pressure is normal. 2. You can inflate both sides to the same pressure or perform a tire pressure reset on the dashboard. As long as the tire pressure is confirmed to be normal, there's no issue. You can visit a 4S shop for a reset when convenient or refer to the owner's manual to do it yourself. 3. If the tire pressure is normal, there's no need to worry too much. Some larger car washes or repair shops with diagnostic computers can also clear the alert.
4
1
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.