What is the Skoda Kamiq?

Where is the cabin air filter located on the Changan Yuexiang V5?

The cabin air filter of the new Changan Yuexiang V5 is located beneath the glove compartment on the passenger side. You can access it by removing the glove compartment. Below is relevant information about the cabin air filter: 1. The recommended replacement interval for the cabin air filter is approximately 10,000 kilometers. There are two types of cabin air filters: one without activated carbon and another with activated carbon. 2. A high-quality cabin air filter can capture dust particles, alleviate respiratory discomfort, reduce irritation for allergy sufferers, enhance driving comfort, and protect the air conditioning cooling system. Cleaning instructions for the cabin air filter are as follows: 1. If the filter is dirty, clean it by blowing compressed air from the reverse side. 2. Hold the air gun about 5 cm away from the filter and blow at a pressure of 500 kPa (5.0 kgf/cm²) for approximately 2 minutes. 3. The cabin air filter tends to accumulate a significant amount of dust. Use tools like a blower or high-pressure air to remove loose dust, but never wash it with water.

16

2

Share

What Causes Car Body Shaking During Acceleration?

The reasons for car body shaking during acceleration include the following: 1. The most common cause of car shaking is a dirty throttle body or excessive carbon buildup in the fuel injectors. When there is too much carbon buildup inside the engine, the gasoline sprayed by the cold-start injectors is largely absorbed by the carbon deposits, resulting in an overly lean air-fuel mixture during cold starts. This causes the combustible mixture to fluctuate between lean and rich, leading to idle shaking after a cold start. 2. Check the condition of the spark plugs, high-voltage wires, and ignition coils. Poor performance in the ignition system or weak spark plug firing can also cause such issues. 3. Abnormal fuel pump pressure or incorrect readings and poor performance of the intake pressure sensor can also lead to car body shaking. 4. Car shaking can be related to the aging of engine mounts (also known as engine mounts or rubber mounts). Engine mounts act as the shock absorption system for the engine, absorbing minor vibrations during operation. If the engine mounts fail, these vibrations can transfer to the steering wheel and the cabin, causing shaking during idle.

5

2

Share

How Much Windshield Washer Fluid Should Be Added to a Fit?

Approximately 2.5 liters of windshield washer fluid should be added to a Fit. To add the fluid, first open the engine compartment hood, locate the inlet for the wiper fluid (usually marked with a corresponding label), and then add the fluid after finding the designated area. Below is a detailed introduction to windshield washer fluid: 1. The market offers three main types of windshield washer fluid: summer-specific, winter-specific, and special anti-freeze types. 2. Summer windshield washer fluid: This type includes an insect-removing adhesive component that helps quickly clean insect residues from the windshield. It also effectively removes insect traces from the front of the car. 3. Winter windshield washer fluid: This type ensures that the fluid does not freeze or damage car components even when temperatures drop below -20°C. In cold winter weather, when cleaning the windshield is necessary, this fluid not only cleans effectively but also absorbs static electricity, making it highly convenient. 4. Special anti-freeze windshield washer fluid: This type remains unfrozen even at -40°C, making it suitable for extremely cold regions.

3

0

Share

How Long Does a Cylinder Head Gasket Last?

Cylinder head gaskets typically have a service life of about two years. Types of Cylinder Head Gaskets: Metal-asbestos gaskets use asbestos as the base material, wrapped in copper or steel sheathing. Some have woven steel wire or perforated steel plates as reinforcement, while others feature metal rings around the cylinder holes to enhance strength. The advantage is their lower cost, but they have relatively poor strength. Due to the carcinogenic effects of asbestos on humans, developed countries have discontinued their use. Metal gaskets are made from a single piece of smooth steel plate, with elastic ridges at the sealing points that rely on the elasticity of the ridges and the effect of heat-resistant sealant for sealing. These are widely used abroad. The advantages are high strength and effective sealing, but the cost is higher. Features of Cylinder Head Gaskets: This sealing gasket has a composite structure, with embossed galvanized steel strips on both sides serving as the core plate. The surface is rolled with soft material, and the sealing gasket usually has a layer of anti-stick coating on the surface.

14

5

Share

What parts should be checked for overhead crane swaying?

Check if the screws on the central shaft are loose. Overhead crane structure: A typical bridge crane generally consists of a lifting trolley, bridge traveling mechanism, and bridge metal structure. The lifting trolley is further composed of three parts: the hoisting mechanism, trolley traveling mechanism, and trolley frame. The hoisting mechanism includes an electric motor, brake, reducer, drum, and pulley block. The electric motor drives the drum to rotate through the reducer, causing the wire rope to wind onto or unwind from the drum, thereby lifting or lowering loads. The trolley frame is the support structure that holds and installs components such as the hoisting mechanism and trolley traveling mechanism, typically constructed through welding. Overhead crane operation: Metallurgical specialized bridge cranes can participate in specific process operations during steel production. Their basic structure is similar to ordinary bridge cranes, but special working mechanisms or devices are additionally installed on the lifting trolley. The operational characteristics of this type of crane include frequent usage, harsh working conditions, and a relatively high working grade.

4

Share

What are the dress code requirements for premium ride-hailing drivers?

Premium ride-hailing drivers are required to wear clean and appropriate attire. Characteristics of premium ride-hailing services: Once a passenger and driver reach an agreement, they can track each other's real-time location changes through the platform, providing passengers with a "visual" waiting experience. These services offer a wide selection of vehicle models, generally of higher quality, allowing passengers to choose according to their preferences for a satisfactory and comfortable journey. Driver income is linked to user ratings, which helps improve service quality. Multiple online payment options are available, making it more convenient for passengers to exit the vehicle immediately after arrival. Premium ride-hailing operation model: The premium ride-hailing operation model consists of four aspects: vehicle source, driver source, production factor combination method, and order acceptance mechanism. Since vehicles serve as the connection point between supply and demand in transportation, the vehicle source in the premium ride-hailing operation model is the prerequisite for driver source, production factor combination method, and order acceptance mechanism. These elements combine to form different operation models for premium ride-hailing services.

6

1

Share

What is the Skoda Kamiq?

Where is the cabin air filter located on the Changan Yuexiang V5?

What Causes Car Body Shaking During Acceleration?

How Much Windshield Washer Fluid Should Be Added to a Fit?

How Long Does a Cylinder Head Gasket Last?

What parts should be checked for overhead crane swaying?

What are the dress code requirements for premium ride-hailing drivers?

What are the charging methods for the BYD Tang?

Can a 4.2-meter vehicle be registered with a yellow license plate?

How Many Times Can You Take the Safe and Civilized Driving Knowledge Test?

What does the GP version of a motorcycle mean?