What is the situation when the engine fault light is on and the throttle is weak?

How Often Should the First Oil Change Be Done?

First oil change should be done every 5,000 or 7,500 kilometers. You can refer to the detailed requirements in the manual. Routine maintenance typically involves changing the oil and filter, which are relatively simple tasks. Engine oil, also known as motor oil or engine lubricant, is a substance enhanced with additives in a base oil. It mainly contains anti-wear additives, detergents, dispersants, and multi-grade viscosity index improvers. Engine oil is used for lubricating internal combustion engines. Its primary functions are to reduce friction and wear on moving parts, and to remove sludge (one of the functions of dispersants) and varnish (function of detergents) from the engine.

12

4

Share

Why does the car's brake squeak?

The causes and solutions for abnormal brake noises in cars are as follows: 1. Use of inferior or overly hard brake pads. Solution: Replace with high-quality brake pads. 2. Presence of foreign objects between the brake pads and brake discs. Solution: When driving at about 5 km/h, quickly press the brake several times; in most cases, this can remove the foreign objects. 3. Severe wear of the brake discs. Solution: Replace with new brake discs. 4. The brake pads have worn down to the warning line, triggering the brake pad alarm. Solution: It is recommended to send the car to a 4S shop as soon as possible for professional inspection and repair.

1

2

Share

What are the main reasons for slowing down when driving a motor vehicle in rainy weather?

The main reasons for slowing down when driving a motor vehicle in rainy weather are: the braking distance of the car will increase, rainy weather will affect the driver's vision, and emergency braking is prone to skidding. When driving a motor vehicle in rainy weather, you need to be more careful and attentive than usual because a layer of fog will form on the car windows, obstructing your view. Additionally, when it rains heavily, the windshield wipers may not be able to clear the rainwater in time. Therefore, when driving in the rain, you must be cautious and keep your eyes on the road conditions. Moreover, when driving in rainy weather, you should also pay attention to your speed, as the roads outside are very slippery, and you need to prevent the wheels from skidding.

15

1

Share

How to Read the Tire Pressure Limit on Tires?

The tire pressure limit can be found on the tire pressure markings. These markings are usually located on the sidewall of the tire, indicating the maximum load capacity of a single tire and the maximum safe inflation pressure under normal conditions. For example, if the sidewall reads MAX.PRESS.350kPa, it means the maximum safe inflation pressure for the tire under normal conditions is 350kPa; MAX.Load615KG indicates the maximum load capacity of a single tire is 615KG. According to the international standard GBT2978-2008, the recommended tire pressures for different types of tires are as follows: Standard tires: 2.4-2.5bar; Reinforced tires: 2.8-2.9bar; Maximum pressure: should not exceed 3.5bar. In winter, the tire pressure should be slightly increased by about 0.2bar based on the standard tire pressure. Generally, the lower limit of the standard tire pressure is sufficient. For example, the lower limit for standard tires is 2.4bar. If the car is often parked outdoors, the tire pressure can be about 0.1bar lower than the standard to prevent blowouts due to high temperatures or damage to the tire pressure sensor.

14

0

Share

Can You Drive When the ABS Warning Light Is On?

When the ABS warning light is on, it is recommended not to continue driving, as the illuminated ABS light indicates a malfunction in the vehicle's anti-lock braking system. During emergency braking, if the wheels lock up, the vehicle may lose control and skid, making it difficult for the driver to decelerate or adjust the vehicle's trajectory, posing significant safety risks. There are various states in which the ABS light may illuminate, each with different causes and solutions, as detailed below: State 1: ABS warning light remains constantly on (most common). Cause 1: The ABS wheel speed sensor's sensing area is covered by dirt, mud, or other contaminants, affecting the sensor's ability to detect the corresponding speed signal. This prevents the ABS control unit from determining the vehicle speed and calculating the wheel slip rate, thus failing to issue appropriate commands to regulate braking. Solution: Clean the dirt from the wheel speed sensor and adjust the gap between the sensor and the signal ring to restore normal function. Cause 2: Poor signal transmission due to loose connections in the system wiring or poor contact in the ABS relay, leading to system failure. Solution: Inspect the wiring connections and reconnect any loose parts. State 2: ABS warning light intermittently illuminates but turns off when accelerating. Cause: When multiple electrical components are in use, the battery voltage drops below 10.5V. As the engine speed increases, the voltage rises, causing the ABS warning light to turn off. This may also occur if the ABS system's power supply voltage is too low due to poor contact in the wiring or grounding. Solution: Check the battery's specific gravity; inspect the charging system; examine the power supply (e.g., voltage relay or poor power contact). State 3: ABS warning light remains on after engine start and only turns off when the engine is turned off (IGFF). Cause: Poor grounding contact in the ABS hydraulic valve body; loose wiring connections in the ABS hydraulic valve body; ABS control unit malfunction. Solution: Loosen and then retighten the grounding screw on the hydraulic valve body, cleaning the contact surface if necessary; check for enlarged gaps in the connectors; replace the ABS or ABS/ASR control unit if needed. State 4: ABS warning light illuminates during high-speed driving. Cause: At high speeds, the ABS control unit detects a significant discrepancy between the rear and front wheel speed signals; incorrect tire or wheel rim specifications. Solution: Refer to the vehicle's tire and wheel rim specifications, as indicated on the label near the fuel tank cap. State 5: ABS warning light intermittently illuminates. Cause: Improper adjustment of the brake light switch; poor internal contact in the brake light. Solution: With the engine running, press the brake pedal and use your finger to push the brake switch linkage all the way down, then release the brake pedal to complete the self-setting position; replace the brake light switch if necessary.

10

5

Share

What are the reasons for the Changan CS35 not starting when hot?

The reasons why the Changan CS35 does not start when hot are as follows: 1. Fuel injector leakage. 2. Damaged carbon canister solenoid valve. 3. Insufficient fuel pressure. 4. Damaged fuel pressure regulator. 5. Poor fuel quality.

6

2

Share

What is the situation when the engine fault light is on and the throttle is weak?

How Often Should the First Oil Change Be Done?

Why does the car's brake squeak?

What are the main reasons for slowing down when driving a motor vehicle in rainy weather?

How to Read the Tire Pressure Limit on Tires?

Can You Drive When the ABS Warning Light Is On?

What are the reasons for the Changan CS35 not starting when hot?

How to Use the Remote Start Feature on the Accord?

How to Adjust the Suspension Stiffness of the Mercedes-Benz S-Class?

What Causes a Vehicle's Idle Speed to Decrease?

What are the safety warning signs?