What is the significance of promoting new energy vehicles?

1 Answers
Menezes
07/25/25 3:09am
Promoting new energy vehicles plays an important role in national economic and social development. The following introduces the characteristics of new energy vehicles: 1. Hybrid vehicles: Equipped with batteries that can conveniently recover kinetic energy during downhill driving. In busy urban areas, the internal combustion engine can be shut down, and the vehicle can be driven solely by the battery, achieving 'zero' emissions. 2. Pure electric vehicles: The technology is relatively simple and mature, and they can be charged wherever there is a power supply. 3. Fuel cell vehicles: They achieve zero or near-zero emissions, reduce water pollution caused by oil leaks, lower greenhouse gas emissions, and operate smoothly with no noise.
Was this review help?
19
3
Share
More Forum Discussions

How Many Points Are Deducted for Running a Red Light?

If there are cameras, they will take photos. Whether a motor vehicle runs a red light while turning left or going straight, it is considered a violation. According to the relevant provisions of the "Road Traffic Safety Law," vehicles must obey traffic signals, including traffic lights, traffic signs, road markings, and the directions of traffic police. If both the left-turn light and the straight light are green, going straight from a left-turn lane does not comply with the designated lane rules. When the left-turn lane has a red light, running it will be penalized as running a red light. The definition of running a red light while turning left: Running a red light is determined by the vehicle's stop line. When the red light is on, crossing the line is a violation. The camera mainly records the vehicle's movement during the red light, focusing on significant positional changes. If the front wheels have just crossed the stop line when the red light turns on and the vehicle stops immediately, the traffic police will not penalize it. However, if the vehicle continues to move completely after crossing the line, it is a violation and will be penalized. That is, the vehicle completes running the red light by crossing (pressing) the line, continuing to move during the red light, fully crossing the line, and entering the intersection during the red light. Here are some ways to avoid running a red light: First look at the arrow light, then the circular light: Currently, there are two types of traffic lights: arrow lights and circular lights. When arrow lights are present, first observe the arrow light and then the circular light to avoid running a red light. Note: When encountering a circular red light, you can turn right; when encountering an arrow signal light where the right-turn arrow is red, you cannot turn right, otherwise, it will be penalized as running a red light. Brake in time: When the red light turns on, do not let the front of the vehicle cross the stop line. If the front wheels accidentally cross, and the rear wheels follow, the electronic camera will capture it, and it will be penalized as running a red light. If the front wheels have just crossed the stop line when the light turns red, do not proceed through the intersection; wait for the green light. Check the green light countdown before proceeding: When the green light is flashing, if there is a countdown, use it to judge; if there is no countdown and the vehicle is close to the intersection with high speed, you may proceed to avoid running a red light due to untimely braking. If the speed is slow and the vehicle is far from the intersection, brake immediately to avoid running a red light. Article 38 of the "Regulations for the Implementation of the Road Traffic Safety Law of the People's Republic of China" states: When the green light is on, vehicles are allowed to proceed, but turning vehicles must not obstruct the passage of straight-moving vehicles or pedestrians. When the yellow light is on, vehicles that have already crossed the stop line may continue to proceed. When the red light is on, vehicles are prohibited from proceeding. At intersections without non-motor vehicle or pedestrian crossing signals, non-motor vehicles and pedestrians should follow the motor vehicle signals. When the red light is on, right-turning vehicles may proceed if they do not obstruct the passage of other vehicles or pedestrians. Running a red light is not considered a violation under the following circumstances: Yielding to special vehicles: Yielding to ambulances, fire trucks, or other special vehicles. If caught by surveillance cameras while yielding, manual review will not record it as running a red light. Even if recorded, you can apply for reconsideration at the traffic police department. Extreme weather: When visibility is very low, and even electronic police cannot clearly see the traffic lights. Photos of violations may be blurry, and mistakenly running a red light will not be penalized. Emergency situations: When rushing a critically ill patient to the hospital, you may run many red lights, and 12 points may not be enough. After delivering the patient, provide proof from the hospital or the rescued person to the traffic police for verification. If confirmed, the violation record can be cleared. If possible, call an ambulance to avoid accidents caused by running red lights. Traffic police direction: During peak hours, traffic police may temporarily direct traffic at important intersections. Drivers should follow the traffic police's hand signals. The traffic police department states that according to the "Regulations for the Implementation of the Road Traffic Safety Law of the People's Republic of China," when the yellow light flashes at an intersection, vehicles that have already crossed the stop line may continue to proceed. If the yellow light is already on and you still rush through, it will be considered running a red light if caught by cameras.
5
3
Share

What is the solution when the car engine emission fault light comes on?

When the car engine emission fault light comes on, the solutions are: 1. Start and turn off the vehicle three times in a row, or disconnect the negative terminal of the engine battery, wait for 30 seconds, and then reconnect it. After completing the above steps, check if the engine fault light on the dashboard is still on; 2. If the fault light remains on and the vehicle cannot be started after turning it off, call for a tow truck; 3. The engine exhaust system fault light usually comes on due to damage to the oxygen sensor in the three-way catalytic system or poisoning of the three-way catalytic converter caused by poor fuel quality. If the light comes on while driving, immediately reduce speed and drive to the nearest service station for inspection and repair.
14
0
Share

Where is the VIN located on the imported Ford Edge?

The VIN (Vehicle Identification Number) of the imported Ford Edge is located on the inner side of the frame under the front passenger seat. The VIN serves as the vehicle's unique identifier, helping owners promptly recognize their vehicle and check if their vehicle falls under any manufacturer recalls by batch. The Ford Edge is a mid-to-large-sized crossover SUV. It comes equipped with the Ford Co-Pilot360™ driver-assist technology, which includes features such as full-speed adaptive cruise control, pre-collision assist with automatic emergency braking, evasive steering assist, lane-keeping system, post-collision braking, navigation-assisted driving, blind-spot monitoring, and active park assist.
16
0
Share

Should the ETC card chip face inward or outward?

ECT card chip faces outward. ETC installation process is as follows: Upon receiving the device, first check whether the ETC card and electronic tag (OBU) are damaged. Press the anti-tamper button on the back of the OBU, the red light will briefly light up, and the OLED screen will display "Tag Invalid" or "Please Insert Card", indicating the device is functioning normally. Clean the front windshield to ensure the glass surface is smooth, clean, and dry. Then peel off the adhesive backing film of the OBU and stick it to the installation position. Press firmly with your hand for 2-3 minutes to remove any air bubbles. Insert the ETC card with the front side facing the driver and the back side facing the front glass. The chip should be inserted into the OBU device. ETC activation method: Insert and remove the ETC card twice in succession until the electronic tag screen displays "Bluetooth On". If "Tag Invalid" appears when inserting and removing twice without the electronic tag attached, this is normal and does not affect activation. Alternatively, you can directly press the button on the top of the electronic tag to enable Bluetooth. Turn on your phone's Bluetooth, open the corresponding mobile APP (usually there is a download QR code on the electronic tag), and enter the device activation interface. Click on device connection and wait patiently for the "Connection Successful" prompt. After successful connection, upload a photo of the vehicle's front to complete activation.
18
2
Share

What does 2.0t mean in cars?

2.0t in cars refers to a turbocharged engine with a displacement of 2.0 liters. Displacement is the total volume swept by all the pistons from top dead center to bottom dead center multiplied by the number of cylinders. Turbocharging is a technology that uses exhaust gases from the internal combustion engine to drive an air compressor. The main function of turbocharging is to increase the engine's air intake, thereby enhancing its power and torque, making the car more powerful. When a turbocharger is installed, the engine's maximum power can increase by 40% or more compared to when it is not equipped with one.
18
5
Share

Is it necessary to replace spark plugs at a 4S shop?

Spark plugs can be replaced either at a 4S shop or by yourself. The specific replacement steps are as follows: Open the hood, lift the plastic cover of the engine, remove the high-voltage distributor wires, and mark the position of each cylinder to avoid confusion. Use a spark plug socket to remove the spark plugs one by one. While removing them, check for any leaves, dust, or debris on the exterior and ensure they are thoroughly cleaned. Place the new spark plug into the spark plug hole, hand-tighten it a few turns, and then use the socket to tighten it further. Reinstall the removed high-voltage distributor wires according to the firing order, and then secure the cover. Spark plug replacement intervals: Under normal maintenance conditions, spark plugs should be replaced every 40,000 to 60,000 kilometers. However, this may vary depending on the brand and engine type, so it is recommended to follow the owner's manual. The following standards can be used as a reference for maintenance and replacement: Platinum spark plugs should be replaced every 40,000 kilometers, standard nickel alloy spark plugs every 20,000 kilometers, and iridium spark plugs every 60,000 to 80,000 kilometers.
15
3
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.