What is the RPM of the Bin Yue?

1 Answers
DiElliott
07/30/25 8:10am
Bin Yue's maximum power RPM is 5200 revolutions per minute, and the maximum torque RPM ranges from 1600 to 4000 revolutions per minute. The following is an introduction to RPM and the ideal state of RPM: Introduction to driving RPM: The higher the engine RPM, the more work is done per unit time, so the power is greater. However, the higher the RPM, the faster the entire cycle speed. Fuel is expelled before it has enough time to burn completely. Therefore, fuel consumption will increase exponentially. So higher RPM is not necessarily better. RPM mainly depends on speed and gear. The ideal state of car RPM: Try to minimize the engine operation below 2000 RPM while driving. If the RPM is too low, you will feel that the engine lacks power. When the engine operates at low RPM with a heavy load, it can cause damage to the engine and easily lead to carbon deposits.
Was this review help?
14
5
Share
More Forum Discussions

Can a sedan pass the annual inspection after changing the rims?

If the modification of the rims has not been approved by the traffic management department in advance, the vehicle cannot pass the annual inspection normally. The following are the time regulations for vehicle annual inspections: 1. Passenger vehicles for commercial use: annual inspection once a year within 5 years, and twice a year after 5 years. 2. Trucks and large and medium-sized non-commercial passenger vehicles: annual inspection once a year within 10 years, and twice a year after 10 years. 3. Small and micro non-commercial passenger vehicles: biennial inspection within 6 years, annual inspection once a year from 6 to 15 years, and twice a year within 15 to 20 years. 4. Motorcycles: biennial inspection within 4 years, and annual inspection once a year after 4 years. 5. Other motor vehicles: annual inspection once a year throughout the entire usage period.
3
3
Share

How to Replace Car Rearview Mirror Glass?

Car rearview mirror glass replacement method is: 1. Press the head of the mirror glass with your hand to make the tail tilt up; 2. Grab the tail with your hand and pull it outward forcefully to remove the old mirror glass; 3. Replace it with a new one. Be sure to distinguish between left and right. On the black plastic clip holder on the back of the mirror glass, the driver's side mirror glass is marked with the letter L, and the passenger side mirror glass is marked with the letter R. Car rearview mirrors are located on the left and right sides of the car's front and inside the car. The car rearview mirror reflects the situation behind, beside, and below the car, allowing the driver to indirectly see these positions clearly. It acts as a second pair of eyes, expanding the driver's field of vision.
2
1
Share

What does C1D mean on a driver's license?

C1 and D driver's licenses refer to a combined license that permits driving both C1 and D vehicle categories. The C1 license allows driving small cars, while the D license permits operating ordinary three-wheeled motorcycles. C1: Small cars, small automatic transmission vehicles, low-speed cargo vehicles, and three-wheeled vehicles. Small and micro passenger vehicles, as well as light and micro cargo vehicles; light, small, and micro special-purpose vehicles; small passenger vehicles with a seating capacity of 9 or fewer people. D: Three-wheeled motorcycles, ordinary two-wheeled motorcycles, and mopeds with an engine displacement exceeding 50ml or a maximum design speed exceeding 50km/h. Application age: The minimum age requirement for a C1 driver's license is 18 years old, with no upper age limit. The application age for a D driver's license is between 18 and 60 years old.
4
0
Share

What should beginners pay attention to after getting a driver's license?

Beginners who have just obtained a driver's license should pay attention to the following points: 1. Probationary driver: The first year is the probationary period, during which the driver must not accumulate 12 penalty points. If 12 points are accumulated, the driver's license will be revoked. After revocation, the driver must reapply for learning, take the test again, and obtain a new driver's license. 2. Driving on highways: If driving on highways during the probationary period, there must be a driver with more than 3 years of driving experience accompanying in the front passenger seat. 3. After the probationary period: After the first year's probationary period ends, there is no need to replace the license, and it can continue to be used. 4. Annual review and license renewal: When the driver's license reaches 6 years, an annual review and license renewal must be processed.
11
3
Share

What is speed matching for gear shifting?

At 15 km/h, shift to 2nd gear; when speed increases to 25 km/h, shift to 3rd gear; at 35 km/h, shift to 4th gear; and at 45 km/h, shift to 5th gear. Below are the speed ranges matched with each gear: 1. 1st gear: Used for normal starting or climbing very steep slopes. The speed is generally around 10 km/h when using this gear. 2. 2nd gear: A transitional gear for acceleration after starting, or used for low-speed driving or climbing steep slopes. The speed is generally around 20 km/h. 3. 3rd gear: Generally used at speeds between 20 km/h and 40 km/h, commonly used for city driving. 4. 4th gear: Can be used at speeds between 40 km/h and 60 km/h. 5. 5th gear: Can be used at speeds above 60 km/h, typically for high-speed driving.
1
2
Share

Why Does a Motorcycle's Idle Speed Drop and Stall Easily When Warm?

Clogged fuel lines are the cause. Below is an introduction to car idling: 1. The function of car idling: Idling is an operational state of a car, where the engine runs in neutral. The engine speed during idling is called the idle speed. The idle speed can be adjusted by modifying the throttle opening size, among other methods. Idling means the engine is "producing power without doing work." When the engine is running, if the accelerator pedal is completely released, the engine enters the idling state. 2. Causes of unstable idling: Direct causes refer to mechanical parts being dirty, worn, or incorrectly installed, leading to changes in cylinder power output, resulting in an imbalance of power among cylinders, which causes unstable idling. Indirect causes refer to abnormalities in the engine's electronic control system, leading to poor combustion of the air-fuel mixture, making it difficult to balance the power among cylinders, thereby causing unstable idling.
16
0
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.