What is the RPM of Emgrand GL at 120 km/h?

1 Answers
Furtado
07/29/25 3:46pm
When the Emgrand GL reaches a speed of 120 km/h, the engine RPM is 2200. The engine speed is related to the number of work cycles per unit time or the effective power of the engine, meaning the effective power of the engine varies with different speeds. Below is relevant information about engine speed: 1. The effective power specified on the engine product nameplate and its corresponding speed are referred to as the rated power and rated speed, respectively. 2. The operating condition of the engine at rated power and rated speed is called the rated condition. The rated power is not the maximum power the engine can produce but the maximum usable limit of effective power determined based on the engine's purpose. 3. For the same model of engine, the rated power value may differ depending on its intended use. Effective torque also varies with the engine's operating condition. Therefore, the maximum torque a car engine can output and its corresponding speed are used as indicators to evaluate the engine's dynamic performance. Typically, a speed sensor is used in conjunction with the signal teeth on the flywheel to measure the engine's speed.
Was this review help?
19
5
Share
More Forum Discussions

What are the differences between rear-wheel drive and front-wheel drive vehicles?

Here are the main differences between rear-wheel drive and front-wheel drive vehicles: 1. Different characteristics: Front-wheel drive is commonly found in economical models, featuring low cost, high transmission efficiency, and low fuel consumption; while rear-wheel drive is usually seen in sporty mid-to-high-end models, known for superior handling, excellent acceleration performance, and relatively higher fuel consumption. 2. Different engine placement methods: Rear-wheel drive vehicles mostly adopt a longitudinal engine layout, which occupies more space and significantly reduces rear passenger space; front-wheel drive vehicles use a transverse engine layout, freeing up more space, and the absence of a protruding driveshaft in the cabin noticeably improves rear passenger comfort. 3. Different handling: Front-wheel drive vehicles require the front wheels to handle both steering and driving, placing a greater burden on them, which can lead to understeer during sharp turns or even difficulty in turning; whereas rear-wheel drive vehicles, due to the heavier rear axle and greater inertia, are more prone to oversteer.
11
4
Share

Where is the engine number located on the old Audi A6 V6?

Old A6 engine numbers are generally located on the lower left side of the engine, and sometimes on the side of the cylinder block near the flywheel. It usually consists of a combination of 7 to 8 digits and letters. In addition to the above method, the engine number can also be checked through the following 4 ways: The vehicle license shows the engine number, usually located on the second last line; The motor vehicle registration certificate will indicate the engine number; The car purchase invoice will indicate the engine number; The vehicle purchase tax payment certificate will indicate the engine number. Note that the engine number is not the same as the engine model. The engine model refers to the specification and size of the engine within the manufacturer, and engine models can be the same. The engine number refers to the production number of the engine, each engine can only use one engine number and each engine's number is different.
1
1
Share

What to Do When the EPB System Fails?

Solutions for EPB system failure are as follows: 1. Turn on the ignition switch. 2. Press and hold the foot brake, then push down the electronic parking brake for 5 seconds. 3. Pull up the electronic parking brake for 5 seconds to complete the initialization reset. More information about the EPB system: 1. EPB stands for Electrical-Park-Brake in English, which refers to the electronic parking brake system, commonly known as the handbrake installed in motor vehicles. The typical handbrake is usually positioned within easy reach of the driver's right hand for convenient operation. 2. The parking brake is used to stabilize the vehicle after it has come to a stop, preventing accidents caused by rolling on sloped surfaces.
11
1
Share

Difference Between Load Capacity and Deadweight Tonnage

The differences between load capacity and deadweight tonnage are as follows: 1. Different Definitions: Deadweight tonnage is a standard for measuring a ship's load-carrying capacity. Deadweight tonnage, also known as total deadweight, is an indicator of a ship's load-carrying capability. It is calculated as the difference between the full-load displacement and the light ship displacement, expressed in tons. The formula for deadweight tonnage is: Deadweight Tonnage = Full-load Displacement - Light Ship Displacement; Load capacity refers to the difference between a vehicle's gross vehicle mass and its curb weight, representing the vehicle's effective loading capability. 2. Different Objects: Deadweight tonnage refers to the total permissible load of passengers, cargo, fuel, fresh water, and consumable supplies on a ship; Load capacity indicates the total mass that a vehicle can carry, including both passengers and cargo.
17
5
Share

What brand of tires does the Fista use?

The Fista uses Nexen brand tires. More details about the Fista are as follows: 1. The Fista features a black large-mouth style front grille, sporty side lines, a Fastback-style sloping roof design, elongated hood lines, segmented dual waistlines, and 18-inch large wheels. 2. Inside the car, you can see a driver-oriented layout design, a 10.25-inch floating central control screen, a 7-inch LCD instrument panel, and seats that are highly sporty and comfortable, exuding understated luxury and taste, belonging to the mid-to-high-end car segment.
8
3
Share

Which tire does not rotate when the car turns right?

When the car turns right, all tires rotate, but the right wheel turns slower than the left wheel. Here are specific details about tires: 1. Tire functions: Tires support the entire weight of the vehicle, bear the load of the car, transmit traction and braking torque, ensure the adhesion between the wheels and the road surface, reduce and absorb vibrations and impacts during driving, prevent severe vibrations and early damage to car components, adapt to the high-speed performance of the vehicle and reduce driving noise, ensuring safety, handling stability, comfort, and energy efficiency. 2. Tire maintenance methods: Tire maintenance includes regularly cleaning stones from tire treads, minimizing exposure to sunlight, frequently checking tire pressure, paying attention to suspension maintenance, periodically inspecting front wheel alignment, and being mindful of driving habits.
15
2
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.