What is the reason why the sunroof of the Jaguar XEL cannot be closed with one touch?

1 Answers
Albuquerque
07/30/25 12:37am
The reasons why the sunroof of the Jaguar XEL cannot be closed with one touch are: 1. Lack of lubrication in the sunroof track, and the sunroof seal being stuck to the body; 2. Foreign objects in the sunroof slot; 3. Damage to the sunroof motor. The functions of the sunroof are: 1. To replace the air inside the car; 2. To remove fog inside the car. Taking the 2020 Youth Sport Edition Jaguar XEL as an example, its body dimensions are: length 4778mm, width 1850mm, height 1429mm, wheelbase 2935mm, fuel tank capacity 62l, and trunk capacity 455l. The 2020 Youth Sport Edition Jaguar XEL is equipped with a 2.0l turbocharged engine, with a maximum horsepower of 200ps, maximum power of 147kw, and maximum torque of 320nm.
Was this review help?
18
1
Share
More Forum Discussions

What is the sound of a motorcycle passing by?

The sound of a motorcycle passing by is the noise emitted by the engine, as it lacks a muffler. Disc brake noise: When a motorcycle goes over bumps or experiences vibrations, the brake pads hitting the metal produce a clanging sound, which is definitely an issue with the disc brake. Rear brake noise: Such sounds are often caused by water or dust inside the brake drum, which does not affect braking performance. However, please note that excessive wear of the asbestos layer on the brake pads can also lead to this phenomenon. If this persists for a long time, it is recommended to replace the brake pads. Engine noise: The causes of this issue are relatively complex, and it is advisable to visit a specialized repair shop for inspection and maintenance. Knocking sound caused by detonation: When the engine suddenly accelerates or the motorcycle is climbing a slope, a continuous sharp "tapping" sound from inside the cylinder indicates knocking caused by detonation. Common causes include an overheated engine, excessive carbon buildup in the combustion chamber, low heat range spark plugs, use of low-octane gasoline, or advanced ignition timing.
2
2
Share

Why is the RVM malfunction indicator light on in the Ant?

The RVM malfunction indicator light in the Ant is caused by a fault in the vehicle's remote system module. Yellow symbol light: Indicates there is an engine fault, but this fault does not affect the normal operation of the engine. However, inspection and repair are necessary. Red symbol light: Indicates there is a serious engine fault. Normally, immediate repair is required. Under special road conditions, emergency driving is possible, but the engine's working condition must be constantly monitored. Once lit, in most cases it will not disappear automatically, and in a few cases it may disappear automatically. This is what is referred to as the engine malfunction indicator light being on.
1
1
Share

What is the height of the Tayron?

The Tayron has a length of 4589mm, a width of 1860mm, a height of 1660mm, and a wheelbase of 2731mm. Comfortable Driving Experience: The Tayron offers technology and comfort features that surpass its class, leading the segment in equipment standards and creating a delightful driving experience for users. Cutting-Edge Technology: The adoption of multiple advanced driving assistance systems, such as the TJA Traffic Jam Assist, ACC3.0 Adaptive Cruise Control, and PLA3.0 Intelligent Parking Assist, provides users with a safe driving experience. Safety Protection: The Tayron comes standard with ESP across all models. With over 60 active and passive safety features, it not only offers the highest standard of safety protection in its segment but also sets a new benchmark for safety in the premium midsize SUV category.
12
2
Share

How to Handle Oncoming Traffic When Driving in Mountainous Areas?

When encountering oncoming traffic in mountainous areas, try to choose a section of the road that is relatively wide, proactively reduce speed, and select a safe spot to slow down or stop for passing. Do not accelerate or drive close to the center of the road to prevent scraping or collision accidents. Preventing Stalling on Uphill Slopes: When driving uphill, shift to a lower gear in advance to ensure the vehicle has sufficient power to climb. If the engine stalls suddenly during the ascent, immediately press the brake pedal, engage the handbrake, place rocks behind the wheels for stability, and then restart the vehicle. Preventing Loss of Control on Downhill Slopes: When driving downhill, use a mid-range gear with gentle throttle application, leveraging the engine's idle drag and intermittent braking to control speed. However, avoid relying solely on foot braking for the entire descent, as the brake pads may overheat and quickly lose effectiveness. Do not shift gears while descending, and never coast in neutral with the engine off.
6
1
Share

Are There Retreaded Tires for Small Cars?

Generally, small car tires are not retreaded; they are directly replaced with new ones after reaching a certain service life. The replacement cycle for tires is 5 years or 80,000 kilometers, and it is recommended to rotate the tires at 40,000 kilometers. If the road conditions are poor, the replacement cycle should be appropriately shortened, with the degree of tire wear being the main criterion for judgment. Causes of Accidents: Worn-out tires can lead to accidents, as the tread may become smooth from prolonged use, so old tires should be replaced as soon as possible. Tread Wear: . Excessive tire pressure can cause wear on the central tread of the tire. Tire Blowout: Overloading may cause excessive friction and lead to a tire blowout, so please pay attention to the maximum load capacity of the tires.
17
4
Share

Does the Passat B5 automatic transmission have shifting shock when warmed up?

Passat B5 automatic transmission has a shock when shifting to D gear after warming up. Valve body blockage: When the transmission experiences jerking, hesitation, shock, slipping, or abnormal noises, in many cases, it is not due to damage to the internal valve body but rather the presence of stubborn dirt and impurities inside. Especially when dirt and impurities accumulate inside the valve body, forming blockages, it becomes impossible to effectively regulate the oil pressure, leading to issues like hesitation, shock, and slipping. To resolve this, the valve body is removed and tested on an oil circuit test bench. Based on the test report, the worn plungers are identified, and the valve body is repaired using imported American equipment. The plungers are replaced and upgraded, and the pressure is recalibrated, which can eliminate the fault. This process typically takes about 5-8 hours. Transmission overheating: At the same time, the issue of transmission overheating cannot be ignored. According to data from the Automatic Transmission Repair Association, over 90% of faulty automatic transmissions are caused by overheating.
18
3
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.